Search Documents

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz, Thiago Soares Lima, Rafael Kakitani

Materiais de interface térmica (Thermal Interface Materials - TIMs) são responsáveis pela troca térmica entre a fonte geradora de calor do processador integrado e o dissipador de calor. Devido ao seu baixo ponto de fusão, boa fluidez e cumprimento com as exigências de regulamentação (Restriction of Hazardous Substances - RoHS), ligas à base de bismuto têm sido investigadas para aplicação como TIMs de alta performance. Neste contexto, a análise das propriedades dessas ligas em função de parâmetros microestruturais torna-se, portanto, de elevado interesse científico e tecnológico para o setor eletrônico. Assim, este trabalho tem como objetivo desenvolver correlações entre propriedades de resistência à tração e a microestrutura da liga Bi-0,28%Ni solidificada sob um intervalo de taxas de resfriamento usualmente obtido em processos industriais. Por meio de microscopias óptica e eletrônica de varredura foi observada uma morfologia tipicamente eutética lamelar, composta por lamelas ricas em bismuto com o intermetálico Bi3Ni nos contornos. Os espaçamentos lamelares (λL) foram, então, correlacionados com os parâmetros térmicos de solidificação, sendo propostas leis experimentais de crescimento microestrutural. Ao fim, observou-se que, para λL < 101 μm, equações do tipo Hall-Petch caracterizam a variação do limite de resistência à tração e do limite de escoamento.

Oct 1, 2019

By V. B. Achanti

This paper deals with the effect of various bit geometric parameters on failure characteristics of rock material. Improvement of rock cutting efficiency of continuous mining machines has been an interesting research topic for the last few decades. In the current study, an automated rotary rock cutting simulator, duplicating a continuous miner, was utilized to study these parameters in the laboratory. Improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn wide spread attention over the years. Research shows that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was utilized in this study while bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Air borne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for the each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in static case to dynamic cutting process failure. The physical and mechanical properties of the rock were also determined in order to assess their influence on the wear characteristics of each bit.

Jan 1, 1998

By THOMAS G. FEAR

THE COAL DIVISION started its share of the annual meeting Monday morning with a study of coal classi fication. A. C. Fieldner was in the chair. The report of the tellers of the ballot for division chairman, stating that Thomas G. Fear had been elected to that office, was read by M. D. Cooper. Mr. Fear acknowledged the honor in a few words. In reviewing the history of the Coal Classification Committee the chairman pointed out that this was its third symposium, the last previous one having been held at the 1930 Annual Meeting. Throughout its work the com¬mittee has had the active cooperation of the Canadian workers who are interested in the subject which should result in a uniform scheme of classification in Canada and the United States. F. E. Lathe, of the National Research Council, Ottawa, abstracted the first two papers of the session entitled "Determination of the Alkali-Soluble Ulmins in Coal," by Edgar Stansfield and K. C. Gilbart, and "Moisture Determination for Coal Classification," by the same authors. The third paper "Condition of Water in Coals of Various Ranks"&apos; was presented by its author, A. W. Gauger. Written discussions of these papers were presented by H. C. Porter and Gilbert H. Cady. In the oral discussion which followed, W. T. Thom, Jr., brought out the advisability of considering age as a factor in classification. Mr. Fieldner favored retaining bed moisture as a partial classification basis, stating that a review of many coal analyses revealed a remarkable consistency in this item in samples from a given mine particularly where the moisture content was not high. Mr. Porter pointed out that the structure and porosity of coal often have much to do with its moisture content and that these vary in different parts of a seam, particularly in anthracite. Mr. Gauger expressed doubt as to whether the Stansfield method gives the true moisture content of coal, which is needed for classification purposes.

Jan 1, 1932

By X Hu, J Björkvall, L Sundqvist Ökvist

The metal production industry is a significant contributor to global CO2 emissions due to the use of fossil fuels such as coal and coke. To mitigate these emissions and meet climate goals, innovative and sustainable technologies are required. Molten salt electrolysis is a promising technology that directly produces metals from their precursor sulfides or oxides using electricity. When combined with renewable electricity and an inert anode, the electrolysis process can be carbon neutral. This paper presents the results of two pilot-scale studies on the electrolytic reduction of metal oxides and sulfides in molten salts. The first study focuses on the electrolytic reduction of chalcopyrite in molten NaCl-KCl salt. The results demonstrate that in situ separation of copper, iron, and sulfur is possible, enabling the extraction of all valuable elements without CO2 emissions. Furthermore, the findings underscore the capability to eliminate impurities like zinc, antimony, arsenic, and mercury from the electrolysis product. The second study investigates the electrolytic reduction of pure/synthetic chemicals of wüstite, hematite, and magnetite, as well as a magnetite-type iron ore in molten NaOH salt. The findings reveal a stepwise reduction of iron oxides from high valence to low valence, ultimately leading to the production of metallic iron electrolytically. Notably, this study underscores the challenges associated with the selection of an economically viable and durable inert anode material for efficient oxygen generation. These results indicate that molten salt electrolysis provides a sustainable and green route for base metal production. The use of this technology has the potential to significantly reduce CO2 emissions in the metal production industry, contributing to achieving climate goals.

Jun 19, 2024

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a &quot;wet&quot; dross is produced, which is subsequently &quot;sweated&quot; in a suitable type of furnace. When &quot;dry&quot; the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the &quot;dry&quot; dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

By William P. Blacutt

This paper describes the strategy, the struggles, and the obstacles encountered during the last two years in the ongoing process to capitalize Vinto. The effort involves the offering of a vertically integrated business package composed of the tin and antimony smelters along with the two principal tin mines of the country. Capitalization: Bolivia&apos;s Innovative Approach for Privatization, the Vinto Case provides a summary of hard-earned lessons. These experiences can be success- fully implemented in other nations committed to transforming their state natural resource sector.

Jan 1, 1998

By R. J. Wasilewski

Elastic constants have been determined on single crystals of maximum-melting-temperature NiAl compound (50.6 at. pct Al) at 25°C. Temperature variations of Young&apos;s modulus in the three principal crystal directions between -150°C and +800°C exhibit no anomalies similar to those repovted for the isomor-phous compounds brass and AuCd. It is concluded that the ordered CsCl structure is stable throughout the temperuture range investigated NICKEL aluminide is a congruently melting inter-metallic compound of CsCl (B2) structure, stable over a rather wide composition range (40 to 54 pct Al). It exhibits a lattice-parameter maximum of a. = 2.883A at 50.6 pct 1,&apos; at which composition the excess aluminum atoms are randomly distributed on the vacant nickel sites;&apos; at higher nickel compositions the excess nickel atoms replace substitutionally in aluminum sites, while at higher aluminum compositions vacancies are present in the nickel sublattice.&apos; For compositions close to NiAl no significant variation in order has been observed at temperatures up to 900°C.3 At high nickel (65 pct) compositions the existence of a martensitic structural transformation has been reported.4 NiAl is isomorphous with the ordered B-brass structure and with the high-temperature structures of AuCd and TiNi alloys close to equiatomic composition. All of these exhibit anomalous elastic behavior as the temperature of their diffusionless transformation to lower-symmetry structures is approached.&apos;-&apos; This behavior has been explained as indicative of low stability of the CsCl structure in these compounds.8 The present paper reports the experimental determination of the elastic compliances of single-crystal NiA1. EXPERIMENTAL METHOD 1) Specimens. Polycrystalline NiAl was prepared by induction melting of carbonyl nickel and high-purity aluminum and casting into solid copper molds in gettered helium atmosphere. The castings thus produced were canned in mild steel and impact-extruded at 1100 to 1200°C to 38-in.diam rod. After the steel sheath was pickled off, the rods were converted to single crystals by repeated high-frequency satisfactorily produced the desired orientations in the form of crystals 38 in. diam by 8-12 in. long. These were subsequently center less-ground to 7 to 8 mm diam by 12 cm long, electropolished (in 80 pct methanol, 20 pct HzSO, at 25°C and 15 v), and their axial orientation determined to 1 deg by the Laue back-reflection technique. The rod dimensions were determined to 0.01 mm and the densities determined from geometrical dimensions and the weight of every specimen. The average density was 5.905 0.005 g per cu cm. 2) Elastic Data Measurements. Room-temperature elastic compliances Sii were obtained by determining to 0.1 cps the fundameGtal resonance frequencies in the longitudinal and torsional vibration modes. At these frequencies the following relations hold: E =p(2lfif =pvl= Sn- 2r[Sll- S12- -£„«] g -P(2iftf = pvf = (s<« - fr(sii - sw - ±s»y where vl and vt are the velocities, and f andft the resonance frequencies of the longitudinal and torsional waves, respectively; 1 is the length of the specimen, and r is the direction cosine factor—{cos2 a • cos2 0 + cos2 a . cos2 y + cos2 0 ¦ cos2 Y}. Given three crystals of orientations (loo), (110), and (111)) i.e., F = 0, 14, and 13, we can obtain six equations for the three unknown compliances, thus providing adequate internal check. Mode mixing can readily occur in the relatively long wavelength resonance utilized here. This could cause a significant error in the torsion wave velocities calculated from the apparent resonance frequenies. Therefore, throughout the present work, a method, described previosl,&apos; was used to ensure that no significant mode mixing took place at resonance. The apparatus used was originally designed for the Elastomat, Magnaflux Corp.. Chicago, 111. determination of flexural vibration resonance frequencies. At room temperature torsional vibration mode could be established by suitable positioning of the thin wires from the input and pick-up transducers, and longitudinal mode by cementing thin magnetic foils at the ends of the specimen, and inducing the vibration by means of electromagnetic transducers. Only flex-ural resonance frequencies could, however, be obtained reproducibly over the temperature range of -150 to 800°C. These data are considerably less accurate, the error in the modulus being estimated at -0.6 pct from the specimen dimensions and the room-temperature Poisson&apos;s ratio. The reproducibility of the resonance frequencies in repeat runs was, however, to better than l in 15,000, hence the relative elastic modulus error less than 0.02 pct. Therefore, the temperature variation of the principal Young&apos;s moduli obtained by flexural resonance, relative to room-temperature values, is believed to be satisfactorily accurate.

Jan 1, 1967

By A. Kowalski

Telvis Limited, manufacturer of an emergency communication dispatcher&apos;s broadcasting system, now introduces the possibility of a remote software upgrade to its devices. The paper presents methods, features and ways to accomplish this task. It describes the mechanisms used and the opportunities that arise from the use of this type of functionality. The mechanism software update presented applies to devices on the surface and in underground areas of mines. The electronics used currently allow the use of remote software updates, but the mining equipment makes little use of these methods. This paper aims to start the discussion on this topic and tries to lay the path of development by showing one of the first examples of the application.

Aug 1, 2013

By R. J. Evans

The Combined Metals Reduction Co.&apos;s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. Pioche Ore The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericitc and graphite. The ore is an exeeptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent,. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent,. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and ire extrcmely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent . minus 150 nicsh shows pyrite, sphalerite and galena still attached. Early Attempts at Ore Dressing Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore sinee. 1913; in fact, a total of 35 commercial and plant laboratories expenmented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effeet a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-—that is, about minus. : 200 mesh—-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considertd practicable at this time.

Jan 1, 1928

By Knapp. Arthur

THE ORDINARY well log is subjected to a great deal of criticism, much of which is well founded. Sometimes, though, the difficulty in interpreting the log is due to the fact that the geologist or engineer using the logs does not know the limitations of the drilling method used. The rotary drill, especially, has inherent limitations that make it difficult, to secure .definite information at all times. The identification of well-defined key beds is about all that can be expected from the rotary log. The formation in a drilled hole, as reported by the driller; has a direct relation to the speed with which the drill makes the hole or to the reaction of the various strata on the bit, called the "feel of the bit." When this is not thoroughly understood by the geologist or engineer endeavoring to interpret the log, the result is an erroneous correlation with other wells or a discarding of the log as worthless. GENERAL TERMS Hard and Soft.-Hard and soft are relative terms. In the case of well logs, they are very misleading as they are used in connection with both resistance to abrasion and resistance to percussion. In technical rock classification, hardness is relative resistance to abrasion. The term brittleness is used in connection with resistance to blows. These terms are misleading to the geologist or engineer who is not familiar with both the cable-tool, or standard tool, method of drilling and the rotary method. In the case of the standard tools, the driller&apos;s report of the hardness of the formation is in terms of its resistance to blows. For instance, a cable-tool driller might be able to make from 30 to 50 ft. a tour in a brittle limestone, which he would call soft and at the same time he might call a relatively soft (from a purely mineralogical standpoint) gypsum hard, because it is somewhat elastic and is not readily broken by blows. The rotary driller would reverse the terms. The limestone is hard in that it resists the abrasive action of the bit, while the gypsum might be soft in that it is readily cut by the rotary bit. It is rare that wells drilled by the

Jan 2, 1920

By Ron Derrick

SX operators have conducted extensive shut-downs and repairs over the years to mitigate solution leaks from failed stainless steel false floors and walls in rectangular mixersettler mix boxes. Hydrodynamic modeling using first principles and constitutive equations of fluid mechanics can inform an efficient structural redesign sufficient to eliminate the plate failures. Updated mix boxes have been performing without failure for over a decade. Given the extensive construction of the original Holmes and Narver mixer-settler design throughout the world that includes stainless steel lined rectangular primary and auxiliary mix boxes, SX operators may benefit from the approach, eliminating costly shutdowns, leaks to containment, and hazardous repairs.

Feb 1, 2024

By P. Saunier, S. Fourmont, R. Stafford, A. Jung, J. Mlynarek

The safe and economical storage of tailings generated by modern day mining operations is possibly the single largest challenge faced by miners today. By nature, tailings are a waste product that have little to no economic value. Yet, their physical and chemical contents can pose incredible environmental hazards if not stored correctly. The variety of factors that are met when designing Tailing Storage Facilities (TSFs), means that in most cases, a low-cost solution is sought to accomplish storage, meet environmental regulations, and adhere to industry best practices. TSFs can be large dam face structures or smaller structures like retention/evaporation lined ponds. Water management is potentially the single largest factor that miners and designers must contend with when constructing a TSF. Water is a necessary component in the process of extracting ore but can be difficult and expensive to remove once it is mixed with solid tailings particles. As a result, the most common disposal of these water containing tailings, called a slurry, is to simply discharge into an embanked TSF (Vick, 1990). These structures, just like any other water retaining dam, can breach releasing contents downstream. Despite modern advancements in TSF design, there have been numerous dam failures that have resulted in tragic loss of life and ecological devastation. Most notably in the last decade, the Brumadinho and Mariana Dam disasters in Brazil killed 278 people in downstream communities when TSF dams failed in 2019 and 2015, respectively (Rotta at el., 2020). Similarly, in 2014, the Mount Polley tailings spill in British Columbia was the second largest tailings spill on record and caused extensive damage to adjacent watershed ecosystems when the TSF embankment was breached (Byrne at el., 2018). While there were indeed numerous unique and underlying factors present in each of these structural failures, a shared element in the devastation was the large-scale release of unstable liquefied tailings

Mar 2, 2022

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025

By Duncan Chalmers, Rob Nowell, Miguel Araos

Australian underground mines produce in excess of 60 mtpa of coal. Most of these use the longwall method, and they require the use permitted explosives (which are called “permissible” in other countries) for challenges that appear during the day-to-day activities. To obtain the approval for these explosives, they should pass Testing Memorandum #2 (TM-2), which sets out the test required for each category of permitted explosive. These categories are P1, P3, and P5. With P5 being unrestricted use and P3 and P1 have conditional use in underground mines. The TM-2 test was originally set up for NG-based permitted products around 1900. With the closing of NG plants around the world, ammonium nitrate explosives were the natural replacement, and therefore these explosives need to pass the TM2. Australia does have a P1-emulsion based explosive available. For high-risk scenarios (like blasting coal), no P5 explosives are available. The lack of P5 explosives has been prolonged for more than 25 years, since the phasing out of nitroglycerine-based permitted explosive products around the world. The main problem has been that when emulsion based permitted products are tested in the deflagration cannon, the results obtained were not considered in the TM2 criteria and therefore the tests were invalid. A research work on permitted explosives began in 2005 funded by the Australian Coal Association Research Program (ACARP). The aim of the project was to address the lack of P5-type permitted explosive (and, potentially develop them further, i.e., develop safer explosives) and understand the behaviour of emulsion explosive and the results they presented in the tests. Both bureaucratic and technical barriers appeared along the way. On the bureaucracy side, the facility was shut down, reopened, and shut down again. In view of these difficulties, assistance was sought overseas. On the technical side, from the very start the results of the tests when using emulsion-based permitted explosives were not established in the criteria, ignitions occurred for trial samples that were expected to be P5-type, etc. The aim of this document is to present the painful journey in the Australian industry to have a P5-type emulsion-based permitted explosive, for use in UG coal. Also, the technical learning acquired about emulsion explosives and the ignition path of mixtures methane / air will be shown.

Jan 21, 2025

By Racquel Nottingham, Marc Mastrantuono

Micropiles often provide a favourable solution for many deep foundation problems especially when significant site constraints such as confined construction sites or vibration limitations have been identified. Often the durability of buried steel elements are heavily scrutinized in order to effectively determine the rates of corrosion and methods to reduce this while still maintaining the structural integrity of the engineered solution. Practices such as sacrificial corrosion loss and the introduction of plastic sheaths have become the go-to methods of corrosion protection. Since the introduction of the micropile, other solutions have been developed, namely protection with an adequate grout encapsulation. This paper will explore corrosion protection of micropiles and the guidelines provided in the published codes and norms. Since few codes define the exact way to verify the durability of these micropiled structures, the existing data is presented and the analysis of grout encapsulation as an effective corrosion protection method is evaluated.

Oct 1, 2022

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Bradley Stoughton

AT THE meeting of the Board of Directors on May 20, the resignation of Bradley Stoughton as Secretary of the Institute was presented and regretfully accepted by the Board. The letter of resignation follows : Gentlemen: About two years ago, I indicated to the President and some members of the Board my belief that the office of Secretary of the Institute should not be a permanent one. It is my observation of events, not only in our own Institute, but also in several sister societies, that too long a tenure of office by the Secretary inevitably leads to a situation which is not good either for him or for the society. After submitting this in writing to the Directors on February 17, 1920, I was overpersuaded by members of the Board to defer resignation until a more convenient time for the

Jan 1, 1921