Search Documents

By R. L. Montgomery

The literature has been surveyed and values recalculated for the heats and free energies of formation of solid rare-earth compounds at 298° K. In most instances it was necessary to estimate the entropies. Thermodynamic properties of aqueous rare-earth ions have also been calculated. INTRODUCTION The accumulation of thermochemical data on rare-earth compounds in recent years makes it possible to review the subject and to obtain more consistent and more reliable information than was available previously.

Jan 1, 1959

Carrying Energy ?Energy ?Power, data, signal, hydraulics, pneumatics? ?Needs to be conveyed from a stationary point to a system in motion ?Cable Carriers (steel and plastic), Festoon Systems, Cable Reels and Bus Bars Polymer Cable Carriers ?Life Line for modern machinery ?Transmitting power, data, signal, hydraulics or pneumatic energy ?Constructed and designed to work in harsh environments, at high speeds and to do this continuously ?Meet a wide variety of cable (Media) requirements ?Virtually maintenance free ?High efficiency

Nov 1, 2011

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By Peter Kowalczyk

The acquisition of submarine gravity data using airborne gravity technology is a practical reality. Ocean Floor Geophysics plans to deploy a free-swimming ROV based submarine gravimeter on a commercial basis in early 2009. The submarine instrument is a variant of the well-used GT-1A airborne gravimeter. Airborne gravity surveys are now routine. The primary factor controlling the accuracy of airborne gravimeters is the precision of the GPS measurement of vertical movement of the sensor platform. The gravity measurements along a flight line are the differences between the output of the gravimeter vertical accelerometer and the estimate of the aircraft vertical acceleration using the differential GPS system. The principle difficulty of moving an airborne gravimeter to a free-swimming submarine platform is the necessity to have an accurate real time estimate of the changing elevation and hence changing vertical acceleration of the platform; GPS doesn't work underwater and an accurate estimate of depth fluctuations to the necessary precision is difficult to acquire. It is interesting that the airborne gravity gradiometer technology, which competes with the airborne gravity technology, was first developed as a classified military application for use by missile submarines during the cold war. Gradiometers were developed for this application specifically to avoid this problem. A gradiometer does not require as accurate an estimate of its vertical position to make a useful reading- it measures gravity gradients, not the gravity field itself.

Jan 1, 2008

By Kimberly Martin

The EFFC/DFI Carbon Calculator provides the deep foundations industry the opportunity to be a leader when it comes to carbon reduction. This tool was created 10 years ago in an extensive effort by the European Federation of Foundation Contractors (EFFC), DFI, member organizations and Carbone 4, a consultant with ex- perience in life cycle assessment. The tool was born out of the fact that governments and clients were asking for embodied carbon information for foundation systems, and that in- dividual companies were building their own calculators to meet these requests. To help all member organ- izations achieve compliance, and to have a sector-specific tool that is certified to the prevailing standards, EFFC and DFI agreed to partner to create the carbon calculator, which is: Excel based and, therefore, easy to learn and use Updated on a regular schedule Certified to ISO 14067, GHG Protocol and PAS 2050 Free and available for anyone to use Even though this tool is free and easy to use, most projects in the industry do not have a carbon calculation performed. The case to use the calculator is more obvious for members in places like Europe where there are stricter reporting standards and government work can be driven by sustainability over cost. In North America this is not the case, yet. Without directives from clients and governments, what can compel the industry to start regularly using this tool and care about the carbon emissions of projects during design and construction?

Nov 1, 2022

By J H. Kyle

Cyanide is a significant cost in gold processing, as well as an environmentally sensitive issue. It has been suggested that precipitation of cyanide from leach liquors as copper-iron-cyanide compounds such as Cu2Fe(CN)6 may account for part of the total cyanide consumption. This may be especially true for ores that are rich in both copper and iron minerals. Ammonia addition has been shown to decrease the cyanide consumption by copper. Cu2Fe(CN)6.xNH3 precipitates have also been postulated to form during conventional cyanide detoxification processes, using oxidants such as SO2/air, with ammonia arising as a breakdown product from the oxidation of free cyanide. The present work has examined the conditions under which such precipitates may form, particularly in gold plant process and detoxification liquors. Ammonia and pH were found to have a large effect on the extent of precipitation. The compounds that were formed were found to comprise mainly Cu2Fe(CN)6.7H2O, as well as a range of NH3-bearing variants. The stabilities of the various precipitates are important from an environmental perspective. The long-term stability of copper ferrocyanide precipitates in tailings dams may be a problem under alkaline conditions and when some free cyanide is present, elevating the measured total cyanide in solution significantly. Case studies including data from actual plants are also considered, and the importance of these effects is reaffirmed from these results.

Jan 1, 2000

By O Ostrovski

Iron ore reduction and iron cementation by CH4-H2-Ar gas was investigated in a laboratory isothermal fixed bed reactor. Iron ore was first reduced to metallic iron by hydrogen, then carburised to cementite by methane. Increasing temperature and hydrogen content accelerated the reduction process. Methane had almost no effect on the reduction process. Meanwhile, higher temperatures increased the rate of cementation and also the rate of free carbon deposition. The optimal temperature for cementite formation was found to be 750¦C. At this temperature, reduction of iron ore to cementite by gas containing 55 vol per cent hydrogen, 35 vol per cent methane and 10 vol per cent argon was completed in about 15 minutes. Addition of sulphur into the reducing/carburising gas strongly retarded the process of cementite formation and free carbon deposition. Cementite is an unstable phase which decomposes to iron and carbon. The rate of cementite decomposition increased with temperature up to 600¦C and above 750¦C . In the temperature range from 600¦C to 750¦C the rate of cementite decomposition decreased with temperature. Cementite was the most stable at 750¦C and least stable at 600¦C. The two-interface grain model was used to describe the process of iron ore reduction and the volume reaction model was employed to model the iron cementation process. The simulated results for both reduction and cementation are consistent with the experimental data.

Jan 1, 2000

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the recrystallization temperature of titanium has been investigated. All additions, except columbium and tungsten, raised the recrystallization temperature. A correlation is obtained between the logarithm of the absolute rate of change of recrystallization temperature with atomic percent solute and the number of uuter d shell electrons attributed to the free atom of the solute element in its ground state. The work of Abrahamson, et aL.1-6 on dilute binary solid solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and recrystallization temperature. It is shown in these studies that the number of outer s and d electrons in the solute are of prime importance in determining the absolute rate of change of recrystallization or transition temperature with composition. Furthermore, the limit of initial linearity (in the curve of recrystallization temperature vs at. pct solute) has been shown to be a function of the number of d shell electrons in the solute for dilute iron- and vanadium-base alloys. To date no complete systematic recrystallization study of dilute binary titanium base alloys has been made. This study together with that of zirconium base alloys 6 will provide the data for the comparison of the effect of the same solutes upon two solvents with the same number of outer d shell electrons.

Jan 1, 1962

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

HENRY M. HOWE, Bedford Hills, N. T. (communication to the Secretary?).-The authors valuable results as to the effects of the air-hardening temperature on high-speed steel may be summed up thus: Influence of Rising Air-Hardening Temperature on. High-Speed Steel Air-hardening microstructure Cutting Properties temperature S Austenite Grain Free Carbide Grains Boundaries Too low Small or Narrow Maximum Too soft undeveloped Intermediate, Well-developed Intermediate Little or even Best correct none Too high Coarse hide, even with Minimum . Weak, brittle, three-rayed crumbling stars Here the suggestion is that as the air-hardening temperature rises it causes two prominent effects, one helpful and the other harmful, the increase of the former exceeding that; of the latter up to a certain point, at which the steel is most useful, and then in turn being outrun by it. The first is the progressive dissolving of the free carbide in the austenite, increasing the stability of the red-hard state. The second is the progressive coarsening of the grains, and thickening of the intergranular cement, developing at last into spandril-like three-rayed stars of the 1,288° specimen. (2,350° F.) of Plate D, thus giving clear proof of incipient fusion, that is of crossing the solidus. This causes intergranular weakness. The individual grains may have great red-hardness, but they do not cohere. They approach the condition of a bag of emery grains.

Jan 6, 1917

By Leo Brewer, Gerd M. Rosenblatt

Thermodynamic calculations predict the species vaporizing from metal-oxide mixtures when reliable free energy functions, enthalpies of formation, and dissociation energies are available for the possible gaseous and condensed oxide components. Calculations of the oxygen to metal ratio in the vapor phase compared with the oxygen to metal ratio in a liquid metal saturated with oxide impurity are presented The possibility of purifying metals contaminated with oxide by vacuum melting or by distillation is discussed. Kinetic considerations affecting rates are neglected. IN recent years extensive information has been obtained on the thermodynamic stability of gaseous oxides of metals due to a variety of new types of measurement. Perhaps the greatest amount of information has come from the application of mass spec-trometry to the study of high-temperature vapors.' In many instances oxides of quite unusual oxidation states are found to be important in the high-temperature vapors. At low temperatures the standard free energy change for a reaction as given by the equation ?F° = ?H° - T?S° is determined primarily by the AH" value. However, at higher temperatures where the value of T in the T?S° term is large, the entropy term becomes equal to or greater than the AH term. At low temperatures only reactions for which AH is negative or only slightly endothermic are of importance. This restricts the main equilibrium species largely to those with completed octets or those with the principle oxidation number of the element. At

Jan 1, 1962

By K. L. Ludeke, A. D. Day

For many reasons, it appears that deep rooted, perennial shrubs offer potential for improved stabilization and provide maintenance free vegetative cover to harsh sites where perennial grasses have not been successful. The major objective was to select various shrub species of arid plants for initial soil stabilization of disturbed mining areas. The very fact that a drought-adapted shrub has a massive root system that can use moisture from a greater volume of mineral waste soil materials suggests that arid environment disturbed soils may be vegetatively stabilized using desirable forage shrubs. A secondary effort is underway to assemble information and plant materials of promising species from many arid regions of the world for reclamation of mined lands. Surprisingly, many of the better plants for arid sites are quite high in protein content. With proper management, breeding, and selection, they may prove to be very desirable livestock feed when mined lands are used in range land areas. Advancements in arid land solid waste stabilization hold favorable promise for many industries that mine and mill in arid regions for effective reclamation of disturbed areas. Particularly exciting is the possibility of establishment of high density maintenance free vegetative cover of climax vegetation that reclaims the disturbed area back to its original land use. Due to high shrub productivity, stabilization potential, nutritional quality, and reclamation success, greater use should be made of shrubs in disturbed land reclamation associated with mining and milling operations in harsh aril environments.

Jan 1, 1986

By Charles L. Morgan

In a commercial effort to characterize deep seabed manganese deposits in the Clarion-Clipperton region of the northeastern tropical Pacific, Ocean Mineral s Company carried out 16 expeditions to the region between -1978 and 1981. During these cruises OMCO collected substantial data. Activities included acoustic profiling, video and photographic imaging of the seabed, and sampling of the deposits with dredges, box cores and free-fall grab samplers. In 1990 the samples, photographs, technical reports and computer data bases which resulted from this work were archived at the Marine Minerals Technology Center at the University of Hawaii. This preliminary examination of the collection focuses on the biological observations made from almost 10,000 photographs of the seabed and the manganese nodule size distributions and compositional data from the free-fall grab recoveries. Regional trends are evident in all three data types. The biological examinations of the seabed photographs show significant geographical trends, with greater abundances of organisms being noted in the northeastern extreme of the region, decreasing toward the southwest (11.4 to 2.7 observations per 100 m2; 460 to 190 g per 100 m2). The nodule size distributions suggest that the ratio of the nodule burial rates to growth rates systematically decreases over the same range (0.65 to 0.36 nodules buried per 1 cm of growth). Preliminary geostatistical analysis of the ore grade data show that, in addition to high local variability, some deposit

Jan 1, 1991

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012

By Thomas C. Palangio

Since the advent of explosives, people have been trying to mechanize the process of loading it into long, narrow holes. Automated loading frees manpower from the arduous task of charging granular, cartridged and slurry explosives. An unexpected bonus of the automation process has been the realization of some valuable side effects such as high throughputs which speed up the loading process and higher loading densities which enhance explosive performance and permit hole patterns to be expanded.

Jan 1, 1990

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

By K. K. Kelley, L. B. Pankratz, W. W. Weller

The heat capacity of columbium (niobium) carbide (CbC ) was measured over the temperature range from 51 ° to 298 ° K, and the entropy at 298.15° K was evaluated . Also , the heat content above 298.15 ° K of columbium carbide was measured to 1,800 ° K. The results were combined with the known heat of formation at 298.15 ° K to obtain values of the heat and free energy of formation over the temperature range from 298.15 ° K to 2,000 ° K.

Jan 1, 1964

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user's manual, including a program listing, is presented in the appendices.

Jan 1, 1974