Search Documents

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By M. D. Marshall

A survey showed that there were 24 bin-related fatalities in the 5 year period of 1975 to 1979 in the minerals industry. Only 4 victims wore safety belts and only 1 of these had a second person attending his lifeline, as mandated by Federal safety regulations. Not one victim observed the three main Federal safety regulations governing work in and around bins. A study was conducted on the force necessary to pull victims partially buried in sand and limestone. Recommendations are made on procedures and safety equipment that can minimize bin-related accidents. A Handbook, directed to the plant engineer responsible for bin design and safety, was also issued detailing bin designs and flow-aid accessories as a function of the flowability of the stored material to better maintain material flow from bins. A comprehensive table of the flowability of many materials produced in the minerals industry is presented and simple procedures given for determining the flowability of materials if not available.

Jan 1, 1984

By E. A. Loria

The Bureau of Mines analyzed the effects of oxygen, nitrogen, and carbon on the tensile properties of electrorefined vanadium in terms of the Petch equation. The effects of the different impurities and grain sizes on the yield and flow stress between 2730 and 770 K were studied. For specimens of like composition, the values of the Petch parameters 01 and ky obtained by two different methods, extrapolation and grain size, were nearly the same. For high-purity electrorefined vanadium, the 01 value at 2730 K was 10,300 psi (5,150 psi shear). The 01 values for this metal at 1950 and 2730 K were lower by factors of 3 to 4 than for three less pure samples of commercial vanadium metal of equivalent grain size. Nitrogen was more effective than oxygen in increasing 01' the increase being about twice as much for the same impurity level. Carbon produced a slight increase in 01 up to 0.024 percent and then a gradual decrease in 01 to 0.11 percent, the maximum carbon content studied. The corresponding ky values followed the same trend in regard to oxygen and nitrogen additions, whereas the addition of carbon produced no variations at either temperature. Dislocations in vanadium are anchored by carbon, oxygen, and nitrogen with increasing firmness in that order. The high purity of electrorefined vanadium was confirmed by low yield stress and high ductility throughout the low temperature range. The metal also exhibited profuse twinning with high ductility at 1230 and 770 K. The effective surface energy for fracture, y, was found to lie between 3.3 and 3.6 x 1()4 erg cm-2?

Jan 1, 1966

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper in which he presents his own A factor. Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blast hole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, e.g. in conjunction with image based fragmentation measurements or crusher modeling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function such as in the KCO model.

Jan 1, 2016

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J. E. Doo1ey

To process and use the heavy ends of petroleum effectively, the development of suitable separation and characterization procedures not currently available was required. A systematic procedure was developed by the Bureau of Mines using such techniques as isothermal and molecular distillation, chemical treatment, silica-alumina gel chromatography, gel permeation chromatography, and spectrometry. Using these techniques, the Bureau achieved a detailed separation and characterization of a 370° to 535° C distillate from Gach Saran, Iran, crude oil. Such a systematic procedure and the semiquantitative data resulting therefrom should be of value in selecting feedstocks and in optimizing petroleum processing operations.

Jan 1, 1973

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

By R. C. Tait

The gold at Giant Yellowknife is intimately associated with a complex mixture of sulphides, including pyrite, arsenopyrite, stibnite, and a wide variety of antimony sulpho-salts. Direct cyanidation has never been feasible. Recovery is almost entirely dependent upon flotation, roasting of flotation concentrate, and cyanidation of calcine. In November 1958, an Edwards-type roaster and an early prototype, two stage Fluosolids roaster, were replaced by a large two-stage Fluosolids roaster of improved design. The new roaster was started at "safe" medium temperatures, but early in 1959, temperatures in both stages were gradually and deliberately lowered to determine whether continuous autogenous roasting could be maintained under exacting low temperature conditions necessary for good extraction. Operation is smooth and continuous with first and second stage temperatures controlled at 925° and 875°F respectively. Plant cyanide ex-traction compares very favourably with extraction from low

Jan 1, 1961

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By H Arvidson, J Vann

When only wide-spaced drilling is available, for example at concept, prefeasibility and feasibility stages, properly implemented linear estimation (including ordinary kriging) predicts grade tonnage relationships that are over-smoothed compared to final production estimates (and production). Non-linear estimation and conditional simulation are alternative geostatistical approaches that can provide more reliable estimates of the recoverable tonnage and grade from wide-spaced drilling. Non-linear estimation and conditional simulation have been rarely used on iron ore deposits. However, these techniques have had wide application in other commodities such as gold and base metals. Conditional simulation has been used in the iron ore industry (eg Guibal et al, 1997); however, its use here is outlined as a means of generating non-linear estimates, not just its use for variability and drill spacing analysis. As a rule, regardless of commodity, the decision to use non-linear geostatistics will necessitate increased skills and require more time. This decision must therefore be justified in terms of cost-benefit. Such cost-benefit analysis is not straightforward, and to help an approach for determining when linear estimates are inadequate is presented. Recommend in this paper is a well-established non-linear geostatistical approach, the global ædiscrete Gaussian modelÆ (DGM) of change of support, as a tool to establish whether moving from linear to non-linear estimates will materially improve estimate results. Also discussed is the additional use of DGM as a block model validation tool. One specific factor contributing to the lack of application of non-linear geostatistical methods in iron is the added difficulties that arise when conditional simulation and non-linear estimates are required to reproduce the numerous and often important correlations between variables in iron ore deposits. Consequently, presented in the paper is a synoptic review of non-linear estimation and simulation methodologies applicable to correlated variables.

Jan 1, 2007

By J. P. Capp

The Federal Bureau of Mines and the Alabama Power Company conducted an experiment in underground gasification of coal at Gorgas, Ala. involving the use of hydraulic fracturing to increase the air acceptance of a coalbed for the introduction of combustion air and removal of product gases. Air acceptance is defined as the flow rate of air which can be injected into the coalbed at 65 p.s.i.g. This was the second time the hydraulic-fracturing technique was used at Gorgas. Sand suspended in a heavy oil served as the fracturing fluid in the first experiment; in the second the sand was two to six times larger and was suspended in a water-starch gel. In addition to providing further tests of the underground-gasification process, the purpose of the second experiment was to determine the effects of the larger sand and greater volumes of a water-base fluid on (1) the extent of the fractured area, (2) the air acceptance of the coal, and (3) the rate at which a gasification path could be carbonized (linked) through the coal, and to compare these results with those of the first experiment. The coal was fractured by injecting 11,000 lb. of sand and 33,580 gal. of water and water-gel at 200 to 600 g.p.m. and 900 to 1,000 p.s.i. The fluid fractured the coal and the sand served as a propping agent to hold the cracks and crevices open. Pressures during the fracturing operation at test boreholes indicated that the fracturing fluid extended only about 150 ft. from borehole H, the point of application of the fracture. Injection of air revealed that the air acceptance of the coalbed within this e t was materially increased. On the other hand, increased air acceptance also was noted at boreholes up to 280 ft. from borehole H and at the electrolinking area 300 to 400 ft. away, indicating that the fracture effects extended considerably farther than was evident from observation. Similar effects were noted at approximately the same distances after the first hydraulic fracture.

Jan 1, 1961

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By J. J. Hoeppner

Accurate determination of moisture in coals of various ranks has long been a subject of intensive investigation. Excellent reviews of methods developed over many years are given by Brown (9)4/ and, with experimental comparisons, by Goodman, Gomez, and Parry (11). As pointed out in these and other writings, one of the principal difficulties in assigning absolute merit to one or another procedure is the multiplicity of conditions under which water may exist in coal and the difficulties involved in obtaining sharp separation and distinction between these classes. Gauger (10) states: Water recoverable from coal is obtained from the following sources: (1) Decomposition of organic molecules (sometimes called combined water), (2) surface adsorbed water, (3) capillary condensed water, (4) dissolved water, and (5) water of hydration of inorganic constituents of the coal.

Jan 1, 1956

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998

By D. Harrington

The occurrence of dust in mines has always been a source of trouble, but for any years, and virtually up to the beginning of the present century, relatively little of a definite nature was known as to the numerous ill effects of dust in mining operations. Even today, with the west amount of time given and attention paid (for at least 40 years in various, countries) to research and observation en dust in mining, and in spite of the experience with it, much information remains to be obtained, before definite, well-authenticated statements can be made as to numerous features connected with the occurrence of dust in Dines an of its effect upon the health and safety of the worker. One statement that can be made with relatively good assurance of being uncontradicted in that dust is a real menace to the well-being of mine workers, and this includes both health and safety. In addition, dust in and around mines and mining plants is one cause of large financial losses to mine owners and operators. FORMATION OF DUST IN COAL MINES IN THE UNITED STATES One definition of mining is "the processes by which useful materials are obtained from the earth's crust; " since virtually all of the useful materials of or in the earth's crust either are solids or must be reached by penetrating through solids, the materials that are moved in mining must necessarily be broken or disrupted, so that almost every phase of the work of loosening the material and transporting it is likely to produce dust.

Jan 1, 1939

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By Erle C. Donaldson

Bureau of Mines engineers examined the chemical and biological treatment of sewage water designed in one case for reuse and in another for subsurface injection. In the first case discussed, approximately 6 million gallons per day of sewage are treated by the activated sludge process followed by tertiary treatment that includes ion exchange. The renovated water is used in the industrial complex. Liquid industrial waste is sent to a waste disposal facility where it is treated for injection into a deep subsurface formation. In the second case, a community of 3,000 people is using a lagoon sewage treatment system followed by subsurface injection of t- treated effluent. Subsurface disposal is used to avoid growth of algae and weeds in a nearby lake to which the treated effluent was originally discharged. The renovation of municipal water for reuse provides a source of water for industries in a semiarid region and may also provide a source for domestic use in densely populated regions where domestic water requirements have priority over industry needs. In addition both waste treatment systems provide examples of the use of subsurface waste disposal to avoid pollution of surface streams.

Jan 1, 1971

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969