Search Documents

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By R. Hogg, Y. Lee, D. E. Rannels

"Lee, Yu-Chen, Richard Hogg, and D. Eugene Rannels. Extracellular matrix synthesis by coal dust-exposed type II epithelial cells. Am. J. Physiol. 267 (Lung Cell. Mol. Physiol. 11): L365–L374, 1994.—Although integrity of the alveolar basement membrane may influence progression of lung injury induced by inhaled particulates, little is known about direct effects of coal dusts on the alveolar epithelium or its extracellu¬lar matrix (ECM). Effects of dust on synthesis of cell and ECM proteins by type II cells (T2P) was thus investigated. Three coal dusts (anthracite no. 867; bituminous no. 1451 and no. 1361) and mine dust MIT-3, of respirable size, were studied as a function of dose and time over 3 days of primary T2P culture. On day 1, 750 µg/ml of 867 were required to increase relative synthesis of ECM proteins (ECM/cell). MIT-3, 1451, and 1361 were without effect. By day 3, 867 or MIT-3 increased ECM/ cell 60-100% at 300 µg/ml; 1451 produced modest, dose-dependent stimulation, whereas 1361 remained without effect. None of the dusts caused significant cytotoxicity. The results show dose- and time-dependent effects of well-characterized coal and mine dusts to modify partitioning of newly synthesized proteins into the ECM and suggest that coal dust exposure may modulate structure or function of the subepithelial basement membrane.basement membrane; cell culture; inorganic dust; lung injury; extracellular matrix deposition; pulmonary epitheliumCHRONIC EXPOSURE to coal dust may be associated with development of pulmonary fibrosis and consequent loss of normal lung function (see Ref. 26 for review). Al¬though the pathways of inorganic dust-induced lung injury are recognized to involve an inflammatory re¬sponse, the underlying pathogenic mechanisms are not understood in detail. Acute and chronic responses to dust exposure involve a variety of interacting cells of the immune system, including macrophages, T cells, and B cells, along with pulmonary fibroblasts. These responses reflect direct effects of the dust particles, as well as indirect effects mediated by soluble factors, including cytokines and eicosanoids (see Ref. 41 for review).Studies of pulmonary macrophages and fibroblasts following silica exposure suggest that dust-induced damage at the airway surface may involve cellular injury through oxidant-mediated pathways. Coal dusts and related inorganic particulates can activate the alveolar macrophage (42) to produce fibronectin (15) and cytokines, such as interleukin-1 or tumor necrosis factor (4) and/or other soluble products which act locally (29) to cause acute cellular injury and to initiate the progression of fibrotic lung damage (16). Type I epithelial cells are typically more susceptible than type II cells to oxidant injury. Type I cell damage and subsequent death leads to denudation of the subepithelial basement membrane (2, 21) and can be associated with leakage of plasma constituents from the pulmonary vasculature into the alveolar compartment (13)."

Dec 1, 1995

By C. J. Wilhelm, John M. Devine, Ludwig Schmidt

"Steel tanks often corrode rapidly in oil fields where the Gas produced with crude contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion.Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no carious corrosive action. These uses indicated that aluminum tanks,be equally effective in counter- acting hydrogen sulphide corrosion. Consequently, in the spring of 1920, an all-aluminum stock tank of 500 barrels capacity and a ""composite"" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co, in Crane County, Tex. These tanks were under observation for one year, the toot being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Reel Co. The results of this preliminary test sustained the belief that aluminum is highly resistance to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the quantities o highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the aluminum Co. that additional tests be made to include production conditions in large quantities of brine would be handled, for pact experience had shown that aluminum often is susceptible to the corrosive action of brines."

Apr 1, 1931

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1976

By R. A. Young

Effective October 1, 1958, President Eisenhower imposed, by Presidential Order, fixed import quotas on lead metal and lead concentrates and also on zinc metal and zinc concentrates. He did this in response to an escape clause case under the Trade Agreements Act filed by many of the large and small lead and zinc mining companies in September 1957. It is the purpose of this paper to give the experience of the lead-zinc industry under this order during its first two years and some observations on what might have come about under different conditions of U.S.A. consumption. Before considering these various experiences and observations, it seems wise to first outline briefly the basic problem which prompted such an order. Under the Tariff Act of 1930, the duty on pig lead was fixed at 2-l/8¢ per pound and slab zinc at 1-3/4e; per pound. The ores, concentrates and closely related products of these metals carried closely related duty rates. The Trade Agreements Act of 1934 and succeeding similar acts had given the, President the power to lower these and other duties. As a result-of various negotiations with foreign nations, by 1951 these duties had been lowered to their present day rates of 1-1/16 per pound on' pig lead and 7/10o, per pound on slab zinc. Related ores, concentrates and semi-fabricated forms of the metals received commensurate treatment. Under these acts, the Tariff Commission has the right to recommend to the President duty increases, specific quotas or both if find that imports have injured the affected industry. He has the right to accept or reject such recommendations, in whole or in part, in the light of the national interest,

Jan 1, 1961

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By L. D. Tracy

"This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.IntroductionThe present report covers conditions and mining royalties in District VIII of the coal fields of Illinois, as designated by the Illinois Geological Survey. The various districts have been described in the reports on the Illinois coal-mining investigations, carried on cooperatively by the Illinois Geological Survey, the engineering experiment station of the University of Illinois, and the U. S. Bureau of Mines. This district includes Vermilion and Edgar Counties, but as the coal-mining operations in Edgar County amounted to only 827 tons in 1923, the data here given have been confined to Vermilion County.A similar report on District VI (Williamson and Franklin Counties) has been issued as Serial 2722 of the Bureau of Minos.A description of geological and mining conditions, and a discussion of market and transportation facilities, have been included because these have an important bearing on the royalties specified and the general conditions of the lease.Mining ConditionsDistrict VIII is better known as the Danville district and in 1923 produced 4,177,000 tons of coal, or approximately L per cent of the total output for the entire State for that year, which was 79,300,000 tons."

Apr 1, 1926

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By C. S. Allbright

This report gives the results of analyzing three groups of crude shale oils by the Bureau of Mines procedure:4/ (1) Oils produced by standard Fischer assay determinations on oil shales from Brazil (Paraiba Valley) and the United States (Colorado); (2) oils produced from Brazilian shale by different retorting methods; and (3) oils from high-temperature retorting of Colorado oil shale in the Entrained Solids retort. It is the second in a series presenting data obtained by analyzing crude shale oils from various sources. The series furnishes information on the general characteristics and compositions of a wide variety of shale oils. Use of a standard analytical method on all samples facilitates comparison of different oils. The 18 oil samples analyzed in this project comprised 3 from assays of Brazilian and Colorado oil shales in the Fischer retort, 9 obtained by processing Brazilian shale in various other units, and 6 from entrained solids retorting of Colorado shale at 1,000° to 1,500° F. The crude oils from Brazilian shale contained about half as much nitrogen as the Colorado oils. Properties of the Fischer assay oils from Colorado shales agreed with some data that relate grade of the oil shale with properties of the crude oil from the Fischer assay. Comparison of results from Fischer assays of oils from the foreign and domestic shales shows that the oil from Brazilian shale contains more low-boiling material and less residuum than either of the two from Colorado shale. This fact is reflected in lower specific gravity, viscosity, and carbon-residue values for the Brazilian oil. Retorting Brazilian shale in the Entrained Solids unit at 1,120° F. produced an oil whose boiling range was generally lower than the boiling ranges of oils obtained by processing in three other retorts at conventional temperatures. The quality of crude oils from high-temperature retorting of Colorado shale in the Entrained Solids process varies with retorting temperature. As the temperature is raised within the range 1,000° to 1,500° F., the amount of the naphtha fraction in the crude oil increases to about 35 percent and the aromaticity to 98 percent.

Jan 1, 1956

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By N. S. Raymon

As part of an interegency agreement with the Energy Research end Development Administration to develop unproved refractory materials for use in coal gasification processes, the Bureau of Mines reviewed the literature to determine the effect of steam, H2, CO, and CH4 as well as the alkali metal oxides K2O and Na2O on refractory materials. Emphasis was given to the performance of high-alumina castable and fired refractories to conditions expected in coal gasification processes. Approximately 85 references were reviewed with 40 cited in the text. The literature was found to contain little data directly applicable to the selection of refractory lining materials suitable for use under the conditions of temperature, pressure, and gas compositions expected in second generation coal gasification reactors.

Jan 1, 1976

By F. N. Bender

Percolation leaching of wad-type manganese ores was investigated, using a novel system of alternate upward passage of sulfur dioxide gas through moistened ore and downward percolation of wash solutions to extract solubilized manganese. Bench and large-scale tests designed to simulate vat and heap leaching were made on four wad ores from Arizona and Nevada and on a pailomelane ore from Arizona. Three of the wad ores required prebaking at 500° to 600° C. to produce a permeable agglomerate that would not slake during percolation washing. The hard-type ore and one of the wad ores that contained a large amount of granular gangue did not require prior roasting. The deportment of the different ores toward leaching and percolation was studied with particular reference to the influence of the sulfur dioxide - oxygen ratio and the effect of gas dilution on the rate of manganese dissolution, dithionate formation, and acid production. Crushed charges of the ores, as coarse as 1 inch and as fine as 1/4 inch, were treated for periods of 5 to 11 days. Percolation of the gas and leach solutions through the charges was achieved without difficulty. The manganese extractions varied between 78 and 97 percent and depended upon the size and type of ore leached. The average quantity of sulfur dioxide required in the larger scale tests was about 2.6 pounds per pound of manganese recovered. The dithionate formation varied from 0.35 to 0.9 pound per pound of manganese extracted depending upon the strength of leaching gas.

Jan 1, 1957

By J. H. Crocket, J. Andy Fyon

"All gold deposits within the Tisdale Group are spatially associated with carbonate alteration zones; however, not all carbonate alteration zones are host to gold mineralization.Within the komatiitic and magnesium tholeiitic volcanic rocks at the base of the Tisdale Group, discordant and stratabound carbonate alteration zones occur throughout. The alteration zones consist of a ferroan dolomite - quartz inner assemblage which is enveloped by calcite-quartz and an outer chlorite-rich subzone. Factors which control the distribution of carbonate alteration include joint systems, flow contacts, synvolcanic faults and bulk composition of the host rock.Two environments of carbonate alteration can be recognized: 1) The subsea-floor alteration zones developed within the volcanic rock succession where hydrothermal fluids did not discharge directly onto the sea floor. Insignificant gold production has come from this alteration environment. 2) Seafloor zones, which represent points of hydrothermal fluid discharge into the hydrosphere, are spatially associated with felsic volcanic rock complexes and are host to syngenetic, auriferous cherty dolomite.Carbonatized, magnesium tholeiitic basalts, which are host to the auriferous, cherty dolomite, are enriched in antimony (>0.35 ppm), boron (>30 ppm), gold (>5 ppb) and lithium (> 35 ppm), but are depleted in copper ( < 70 ppm), with respect to carbonatized basalts not associated with gold. Orerelated, altered komatiitic flows can be screened using gold (>5 ppb), lead(> 10 ppm), arsenic(> 70 ppm) and antimony (>1 ppm).The habit, petrographic characteristics and certain geochemical characteristics of the altered volcanic rocks suggest that the hydrothermal fluid was of sea-water origin."

Jan 1, 1982

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005