Search Documents

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By F. W. Wellmer

"This paper discusses the changing nature of reserve/consumption ratios, using data from Canadian operations and focussing particularly on copper.IntroductionStudies in world metal consumption and world metal reserves are done regularly by the U.S. Bureau of Mines, the German Federal Institute of Geosciences and Raw Materials, and other institutions. Formerly, on the basis of these data, the following figures were calculated:• a static lifetime of reserves-reserves at year end divided by the consumption of the previous year;• a semidynamic lifetime of reserves-reserves at year assumed constant growth rate.These figures were severely criticized because they were purely theoretical and did not consider the availability of the raw materials.Recent practice is to calculate reserve/consumption ratios (R/C ratios) for periods(1) or for different years(2,3) and to interpret the trend. For base metals, these R/C ratios are increasing (Table 1). This had led to the conclusion that today the relative availability of base metal reserves has increased as compared to 10 or 15 years ago(4,5) As there are normally numerous deposits for each commodity, the anticipated production rates of deposits are irrelevant to this conclusion as long as the statistical distribution of possible production rates does not change significantly.The above conclusion is only justified if the quality and the nature of the data base remain the same. This is certainly the case for the consumption data. It is also assumed for the quality of the reserve figures, which usually take into account only proven and probable reserves. For the nature of the reserve figures, however, this does not seem to be true.Undoubtedly, the reserves increased in absolute terms between 1966 and 1978. To put the absolute reserve figures into perspective, it is common, as said above, to compare them with the mine production, which increased in the free world between 1966 and 1978; e.g. for copper by 40%, for Pb by 17% and for zinc by 36%. However, the reserves are also influenced by other factors, such as average size of the mines, changes in the grade of the mined ore, price-to-cost relationships and the like.The purpose of this paper is to examine the nature of the reserve figures in more detail. Because the completeness of mining data published in Canada is rather exceptional, Canadian .data serve as an example and it is assumed that the conclusions can be extrapolated to other mining countries or at least to those with free market systems."

Jan 1, 1981

By Carl A. Zapffe, George A. Moore

IN a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal sub- structures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the "disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, un- affected by chemical attack and undistorted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. MATERIALS STUDIED In commercial steels, defects caused by hydrogen take various external forms ac- cording to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement-"pickling brittleness"-in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free- machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This , choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group I: Prepared from Armco Ingot Iron As shown in Table I, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

More than 400 academic, Government, and industry representatives attended the third symposium on ash utilization and technology held in Pittsburgh, Pa., March 13-14, 1973. Sponsored by the American Public Power Association, Edison Electric Institute, National Coal Association, National Ash Association, and Bureau of Mines, the symposium Featured 26 formal presentations by leading experts from Europe and the United States on all major phases of ash production, utilization, and research. Abstracts of all the papers are grouped right after this introduction, and the full symposium proceedings follow. Sponsoring organizations and their chief representatives were the National Coal Association, James R. Garvey, Bituminous Coal Research, Inc.; Edison Electric Institute, C. E. Brackett, Southern Electric Generating Co.; American Public Power Association, Herbert Blinder, Columbus (Ohio) Electricity Division; National Ash Association, Inc., James N. Covey, Rochester Gas and Electric Corp.; and the United States Department of the Interior, Bureau of Mines, William L. Crentz.

Jan 1, 1974

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

By M. Frenzel, K. Bachmann, M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmann, L. Pereiraa, K. G. van den Boogaart, N. Kupka

Geometallurgy - the science of predicting the behaviour of ores along the value chain based on their geological and mineralogical characteristics - has barely moved beyond process minerology studies. These studies typically link process behaviour to the mineralogical and microstructural characteristics of pristine or processed ores in a qualitative or semi-quantitative manner. Eventually, a trial-and-error optimisation of the operation is achieved. However, to deliver on its promise, geometallurgy should progress beyond this current approach to a fully quantitative understanding of process behaviour, including the various uncertainties involved, namely predictive geometallurgy. One of the barriers currently hindering this development is the neglect of most ore characterisation data obtained in geometallurgical studies. This is mostly due to the large extent of this information exceeding the capacity of conventional software. To address this challenge, we developed a data mining platform consisting of an SQL database, an R front-end in-house package, and back-ends to interpret data from several analytical instruments. This platform enables the use of the statistical and data mining power of the R open-source environment for any geometallurgical study. Potential applications range from ore characterisation to process understanding and forecasting, and from geostatistical prediction to operational control and optimisation. The scripting abilities of R allow for the: 1) processing of many streams in loops, thus freeing the user from repeating tedious click-and-drop tasks; 2) computation of virtually any derivate or aggregate quantity from the data; 3) distribution of the work among several processor clusters; and 4) keeping of a log file for the calculations done. This contribution presents the building blocks of this platform, and illustrates with several examples its potential to enable predictive geometallurgy. Keywords: Data mining, entropy, kernel methods, LASSO regression, predictive geometallurgy

Jan 1, 2020

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By Carl A Zapffe, George A. Moore

In a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal substructures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the L'disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, unaffected by chemical attack and undis-torted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. Materials Studied In commercial steels, defects caused by hydrogen take various external forms according to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement—-"pickling brittleness "—in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free-machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group 1: Prepared from Armco Ingot Iron As shown in Table 1, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By Carl A. Zapffe, George A. Moore

In a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal substructures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the L'disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, unaffected by chemical attack and undis-torted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. Materials Studied In commercial steels, defects caused by hydrogen take various external forms according to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement—-"pickling brittleness "—in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free-machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group 1: Prepared from Armco Ingot Iron As shown in Table 1, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By R. Hildebrandt, K. Cybulski, G. V. Goodman, Z. Dyduch, M. L. Harris, M. J. Sapko

Past research showed that bituminous coal dust remains dry and dispersible in the presence of moisture. Rock dust must disperse with the coal dust to effectively inert a propagating coal dust explosion. Non-treated rock dust readily absorbs moisture, limiting its dispersibility, while anti-caking treated rock dusts can remain dry. The National Institute for Occupational Safety and Health contracted the Central Mining Institute in Poland to conduct large-scale testing in their Experimental Mine Barbara to determine if a treated rock dust can be as effective as non-treated rock dust in attenuating or quenching coal dust explosions under the same experimental conditions. INTRODUCTION One of the goals of the National Institute for Occupational Safety and Health (NIOSH) is to conduct research to reduce the risk of mine disasters and provide workplace solutions to reduce the risks associated with accumulations of combustible and explosible materials; the most common form of which is the generation of coal dust during the mining process and its subsequent distribution downwind. Dispersible rock dust is a primary defense for preventing coal dust explosion propagation in underground coal mines, and its properties are defined in 30 CFR 75.2. “Pulverized limestone, dolomite, gypsum, anhydrite, shale, adobe, or other inert material, preferably light colored, 100 percent of which will pass through a sieve having 20 meshes per linear inch and 70 percent or more of which will pass through a sieve having 200 meshes per linear inch; the particles of which when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air; and which does not contain more than 5 percent combustible matter or more than a total of 4 percent free and combined silica (SiO2), or, where the Secretary finds that such silica concentrations are not available, which does not contain more than 5 percent of free and combined silica.” An earlier NIOSH investigation of rock dust revealed two significant concerns with the supply of rock dust to U.S. coal mines: 1) insufficient particles <200 mesh (75 μm) and 2) all rock dusts when wetted and dried formed cakes and were not easily dispersed with a light blast of air (1). Past research by the U.S. Bureau of Mines and others showed that bituminous coal dust remains dry and dispersible in the presence of moisture (2). Rock dust must also be dispersible in concert with the coal dust to effectively inert a propagating coal dust explosion (3, 4, 5, 6). Non-treated rock dust, however, readily absorbs moisture, limiting its dispersibility, while a rock dust treated with long-chain fatty acids (such as stearic acid) can remain dry and dispersible. Stearin-treated rock dust has been used in British coal mines (7) and is commonly used in Polish coal mines.

Jan 1, 2019

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia&apos;s measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia&apos;s measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980

By R. C. Rowe

DR. W. F. GRAY (Contributed discussion, presented at meeting by Mr. S. C. Mifilen): Mr. Rowe&apos;s suggestion that the Institute should organize itself to interpret the needs of the mining industry to federal and provincial mines departments should commend itself to our membership as sensible and practical, and as one which these public administrative bodies may welcome. One has to start with the premise that those who head the departments of mines in question have the welfare of the industry at heart. Also, it must be postulated that the technical viewpoint of our membership is necessarily free of political considerations. With these reservations, one ventures to state that both Mr. Rowe in his communication to the present session of the Institute, and Professor M. Y. Williams in his earlier communication to the Western Meeting, on The Geological Survey and Mining Development (1), voice the regret general among our membership at the abandonment of the honoured name, and to some extent of the status, of the Geological Survey of Canada. The writer, in 1932, devoted his Presidential Address to the Institute to an appreciation of the value to Canadian mining of the Geological Survey of Canada (2), affirming the desire of the Institute "that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country will permit, because, to scrimp expenses on the Survey, is &apos;to save at the spigot and lose at the bunghole&apos;." He believes that is still the opinion of the Institute, and, if contraction of the usefulness of the Survey is feared by our members at this time, it is incumbent upon the Institute, in fairness to those who direct our government, to say so in precise and explicit terms. Mr. Rowe puts the situation pithily when he writes: "We have reached a stage in our development where a stock-taking and co-ordination of existing knowledge and data is essential. This is a part of that basic function of Dominion mineral technical services which is national and not provincial in its scope".

Jan 1, 1939

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By George S. Rice

The major purpose of this bulletin, as indicated in the preface by Dr. John W. Finch, Director of the Bureau of Mines, is to give a critical review of the coal-mining methods used in the principal producing countries of Europe, to describe the reasons underlying the adoption of these methods, and to contrast them with coal-mining methods employed in the United States. The report includes discussions of various subjects intimately related to coal mining, such as geology of the principal coal fields; production and resources of the several countries; mine safety and health research; Government mining regulations; mine inspection and rescue procedure; safety lamps; fixed lighting methods under-ground; testing electric motors, mining machines, and mining explosives for permissibility; and special mining hazards, such as explosions of gas and coal dust, mine fires, instantaneous gas outbursts, ground movement and surface subsidence, and bumps. Commercial, economic, and labor problems of European coal mining, including miners&apos; output, wages, and social-insurance schemes, as well as cost of mining, prices of coal, etc., are briefly described. It will be noted that data on most subjects are not given for Russia, which has become an important coal-producing country, owing to the lack of reliable published information concerning Russian coal mining.

Jan 1, 1939

By J. Koster

[In lQ jG thc E&apos;lcct,ro:~(: L7.l :~u..-ic:ll S;%cti ?n of t?c :I. tcIl~tr,-;lcal 3:vi cioa, ?U~CE~U of lv!irtos, bc,~m an 9.ct iv.t In-:?*t ik7;5i GI of r.:ct.l-;c?;is for rccovcrin,; niclrel, cop?ir, an2 ?? cciou:; ~ot-1 c 1;-on or; :; of tile 3unl~crvi~.l~~ tiistrict in C1ni.k Coult:r, !Icl.r. ]

Jan 1, 1939

By J. Koster

[In 1178 thn S-00n of thr !~Viluralcal Divicion, pur--&apos;11 cf Mines, bcran an o. &apos;t iv in&apos;: n-t!Y_Vnn of vothod; for recoverin&apos;-1, Achol, copp~r, nK precioun notnin Zycn o;. -z of tic Bunkcrvillo KOH& in Clark County, Tcv. Tho Bunkcrvillo ran arc of t,-j)(,e of -iincrilization similar to that of 02 SWbury, Ontario, CannO, nichvl dc-?o?-:.t,. At prcoont, only n anall tonnes? p of ore has loan cxDr)scd in t*ic&apos; :hui:er7ilIp rc: inn, ann. there is decided nce! for orjn: izod OrospectiAg ina drvclo-nnnt "crk there. It wann believod, howevar, t4it the dc,cuits varo 3ilficUntly siSnIficant to warrant an investigation iito their]

Jan 1, 1939

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945