Search Documents

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By M. V. Sowmya

Batch biosorption experiments were carried out for the bio-remediation of Cr (VI) ions from aqueous solutions using Serratia marcescens, a Gram negative, heterotroph and Gram positive bacterial isolates from a chromite mine. The influence of various experimental parameters such as contact time, pH, concentration of Cr (VI) ions and amount of biomass was evaluated with respect to the uptake of Cr (VI). The bio-sorption of Cr (VI) was found to be quite rapid and the percentage biosortion was found to increase with increase in the equilibrium chromium concentration. The free energy of biosorption of Cr (VI) was estimated to be in the range of -23 to -25 kJ/mol for the chosen bacteria. The uptake of chromium by the bacteria was confirmed by EDX and FTIR spectroscopy. As a follow up of this study, bacterial strains resistant to hexavalent chromium were isolated from a chromite mine in Karnataka, India and identified as Arthrobacter sp., Micrococcus sp. and Exiguobacterium sp. using 16s rRNA sequencing. The efficacy of the bacterial isolates for Cr (VI) uptake was assessed and over 90% bioremoval could be achieved for Serratia marcescens and Micrococcus sp. isolate. Possible mechanisms of chromium uptake by the microorganism are discussed. Keywords: bioremediation, hexavalent chromium, biosorption, bioreduction

Sep 1, 2012

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By HENRY M. HOWEL

1. Introduction.-The first part of this papers treats of the causes and the restraining of piping in steel ingots; the second& considers the causes and the restraining of -segregation; and the third proposes certain precautions in engineering specifications concerning these two defects. Into their causes I have looked carefully, with the purpose of arriving at rational methods of restraining them, and at efficient ways of detecting. and measuring the harm which they cause, so as to benefit the public by reducing this harm at once effectively and with the least expense to the manufacturer, and therefore in the end with the least expense to the consumer. In Part I., I infer that the pipe is chiefly due to what I, call the virtual expansion of the outer walls of the ingot in the early part of the freezing. I find that the upper and smooth-faced part of the pipe probably forms while the interior is still molten, but that the lower, steep, and crystal-faced part probably forms in metal which is already firm. Of the five causes which may co-operate to limit the depth of the pipe, I find that three-blow-holes, sagging, and the progress of freezing from below upwards-are usually effective. I find that the pipe may be lessened by casting (1) in wide ingots,; (2) in sand molds, especially if these are pre-heated (this is rarely expedient); (3) at the tops instead of at the bottom; (4) slowly; (5) and with the large end up; (6) by the use of a sinking-head or other means of retarding the cooling of the top; (7) by permitting blow-holes to form; and (8) by liquid compression.) Most of these I consider in some detail, and in particular I dwell on the advantages of casting with the large end up, and I propose certain administrative arrangements to permit this.

Mar 1, 1907

By M. K. McCarter

Surface mining applies to extraction of mineral resources from water and sediments of rivers, lakes, seas, and oceans; from solutions circulating through broken rock and soil; and from rock and soil excavated from the earth. Surface mining is responsible for the majority of mineral production in the United States and a substantial portion of the world?s total production. This section deals specifically with extraction methods which employ mechanical processes in a relatively dry environment to free minerals from the earth. The following section, Section 15, deals exclusively with aqueous methods. With recognition of the importance of reclamation in all activities which temporarily disturb the earth?s ecosystems, it is appropriate to classify mechanical extraction methods as either deferred reclamation or concurrent reclamation. Deferred reclamation is necessary when the shape and logistics of the excavation require that it remain open throughout the productive life of he project. Upon exhaustion of economic reserves, the opening is then reclaimed in a manner consistent with public safety, environmental acceptability, and land use policy. Methods employing deferred reclamation are commonly referred to as open pit or quarry mining. Metallic ores, industrial minerals, and coal are all extracted using open pit methods. Typical examples are provided in Chapter 14.1.

Jan 1, 2008

Editor?s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice-chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor. Rajesh Raitani, member SME, of Cytec Industries Inc., is chair of the Industrial Minerals and Aggregates Division?s Technical Committee. The technical Committee vice chairs include: ? Vishal Gupta, member SME, of FlSmidth, Agricultural Materials. ? Candace Trimble, member SME, of Oil- Dri Corporation of America, and Bradley Van Gosen, of the U.S. Geological Survey, ceramics and refractory materials. ? Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials. ? Russell Winn, member SME, of R.E. James Gravel Co., chemical raw materials. ? Justin Zdunczyk, member SME, of Plum Creek, construction materials. ? Jerry Gauntt, member SME, of Golder Associates, fillers and pigments. ? Michael Cheshire, member SME, of Los Alamos National Laboratory, sorbents, filters and process aids. ? Rajesh Raitani, member SME, of Cytec, Industries Inc., specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jul 1, 2013

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By C. E. Dobbin

The coal fields of Montana are widely distributed through the plains region in the eastern and northern parts of the State, and the mountain regions in the central, southern, and southwestern parts of the State. (See fig. 1.) SURFACE FEATURES The Fort Union region in eastern Montana is a broad plain of almost horizontal rocks, characterized by extensive "bad lands" along the larger streams and by red hills, benches, ridges, and buttes which represent shale and sandstone that have been fused by the burning of an underlying coal bed.

Jan 1, 1932

By Lloyd A. Morley

This seven-chapter document is the first volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. After a short introductory chapter, Chapter 2 discusses the history of electrical use in mining and introduces "typical" mine- power-system arrangements. Chapter 3, 4, and 5 supply basic information on electrical theory, circuit analysis, and motors. Next, the Grounding and Distribution Chapters detail unique aspects of mine power systems. Elements of surface and underground use are included in all these chapters. An index concludes Volume I and is cross-referenced to both report volumes.

Jan 1, 1982

By Samer Sadek, Brian Hagan

We are thrilled to welcome you to the 2025 Rapid Excavation and Tunneling Conference (RETC), which will be held in Dallas, TX. This year’s conference will showcase the continued trend of strong industry interest, as there will be a record setting 115 papers being presented over the course of three days. The set of papers compiled in this book captures the latest and greatest information on a broad array of topics within our fascinating tunneling industry. We hope that the compilation of selected papers in this book will provide a comprehensive recap of the conference while also providing a source of future reference for contractors, engineers, and anyone in general who is a student of our beloved and unique industry. Since its inception in 1972, RETC has been the preeminent tunneling forum to promote ideas, tell stories, share lessons learned, and promote new technologies. RETC prides itself on its focus towards highlighting real-world experiences and practical ideas, with the intent to help the entire industry learn from one another and grow. The need for us all to stay sharp and remain on the cutting edge of technology has never been stronger – the technology and ideas that have been applied in aerospace are now attempting to mix with tunneling, and the advancement of AI continues to permeate all industries. However, no amount of technology or AI can fully replace the human element, and in our tunneling industry, the human element is key and is what sets us apart. In tunneling, every project is different, because the ground is always different. We can only take what the ground will give us, and we must rely on our past experiences to get through present day challenges. Most importantly, we must rely on each other. This is the heart of what RETC is all about. For those of you attending this conference, we encourage you to attend as many sessions as possible and engage with your colleagues to discuss during the breaks in between sessions. This sharing of ideas is what keeps us connected and helps to expand our industry. Please also try to engage with the scholarship students and the newcomers who will be in attendance, as it is the new ideas and fresh energy from the next generation that will continue to make our industry thrive into the future. The program chairs thank and greatly appreciate the efforts made by our session chairs, co-chairs, authors, the members of the RETC Executive Committee, and most importantly the SME staff towards making this RETC possible.

Oct 1, 2025

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By X. K. Lan

The greater demand for high-quality large-diameter crystals has led to the robust idea of a free- flying solar-powered furnace satellite, whereby the buoyancy-driven convection effects are almost nonexistent, and diffusion-controlled crystal growth with minimal radial segregation is promoted. In the proposed solar furnace, a paraboloid of revolution imaging concentrator is used to focus the sun's radiation onto an-ampoule which holds the solid charge to be processed. The charge will start melting in the vicinity of the focal point, after which it is translated in order for the melt to resolidify as a single crystal. A ray-trace method has been developed to determine the incident concentrated solar heat flux on the ampoule surface for a perfectly-aligned configuration with an incoming columnated beam. A transient 2- dimensional conduction problem with phase change is formulated, which is solved using the commercial code FIDAP. Results highlighting the feasibility of growing GaAs, Ge and Si crystals with diameters of the order of 20 cm using the solar furnace satellite concept are presented. The transient temperature fields within various charge materials are quantified.

Jan 1, 1994

By Dale Zacherl, Andreas Buhr, Rainer Kockegey-Lorenz

"The microporous calcium hexaluminate insulating material SLA-92 has been introduced as an alternative to refractory ceramic fiber and other insulating refractory materials. Key properties associated with this product include: high chemical purity, long term high temperature stability up to 1500 °C, low thermal conductivity up to 1500 °C, and high thermal shock resistance. The properties of the new material and various applications in the steel and ceramic industries have been reported in previous papers. The current paper summarizes the industrial application experiences with innovative refractories based on SLA- 92 and discusses potential new applications in various manufacturing as well as energyrelated industries.IntroductionSLA-92 was introduced to the refractories industry in 1998 by van Garsel, et al. [1] as a new insulating raw material for high temperature applications, followed by investigations [2] of long term temperature stability for this new lightweight aggregate up to 1500°C.SLA-92 was developed as an innovative alternative to commonly used refractory ceramic fibers. It has unique properties regarding chemical purity and mineral composition and is a microporous, silica-free calcium hexaluminate (CA6 – mineral name: hibonite)."

Jan 1, 2010

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are establishes it can be ascertained with a degree of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and. built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town' whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well underdrained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive.Enviroment. The contiguous territory should afford no unwholesome sur¬roundings such as swamps Or accumulations of stagnant water.General Considerations. The water supply to be provided and the method of disposal of wastes influence to a certain extent the location of the camp or town-site. The means of supplying water, whether by gravity or by pupping, and the disposal of sewage, whether by outfall, system, sewage disposal system through septic tanks, broad irrigation or filter beds, or cesspools will govern the location of the site topographically in relation to source of water and point of disposal of sewage.* This article was prepared as part of the paper ""Use and Supply of Water for the Oil-Shale Industry"" by J. J. Jakowsky, to be published by the Department of Metallurgical Research, University of Utah, in cooperation with the United States Bureau of Mines."

Jul 1, 1921

By R. V. Ramani, R. L. Grayson, R. L. Frantz, V. A. Marple, W. R. Myers, K. L. Rubow, Mutmansky. J. M., T. J. Stobbe

"An investigation of protocols for research performed from 1953 to 1988 on pneumoconioses (with emphasis on diseases related to coal and silica) was conducted in the Generic Mineral Technology Center for Respirable Dust. In addition, interviews were conducted with prominent U.S. medical researchers, aerosol scientists and engineers in government, industry, and universities to determine dust sources, dust preparation methods, laboratory protocols, and determinant variables related to in vitro and in vivo research and assess the comparability of results.Since the original report on the protocol project, additional research regarding free radical existence in freshly produced dust particles and the shape and contamination of particles generated for research purposes has further heightened scientists' concerns. As indicated by current research, fresher dust particles and those with more angular shapes may have a different level of reactivity in biological systems than do older or more rounded particles. Therefore, research on dust preparation methods for biomedical studies was undertaken and will be outlined here.Results of protocol review and interviews are summarized. Research on size reduction methods and their particle characteristics plus some recommendations concerning dust preparation methods and reporting in biomedical publications are also presented. Recent evidence indicates that these recommendations may be of importance in comparing and interpreting research results."

Nov 1, 1995

By O. D. Khmelnitskaya

The research on selecting of an efficient technology of pyrite cinders complex treatment, sulfuric acid production wastes, have been made. The grades in the initial product were 2.04 g Au/t, 35.0 g Ag /t, 0.38%Cu, 1.1% Zn. Laboratory tests on cyanide technology, thiourea and sulphite leaching were carried out. Magnetic and flotation beneficiation and biohydrometallurgical technology were tested. After considering the results of the tests, the most economically efficient technology of pyrite cinders complex treatment with cyanide leaching of precious metals was determined. The technology involves water washing of soluble copper and zinc compounds, lime treatment and cyanide leaching of gold and silver, detoxification and utilization of mineral wastes. The precious metals are recovered from solutions by cementation onto zinc. Copper is recovered from rinse waters by SW/EW and then zinc is precipitated as hydroxide. All the solutions and organic agent are used in recirculation and therefore the technology is practically waste-free. Mineral wastes can be used as iron-containing materials for cement industry. The technology has been tested in pilot-plant scale under continuous operation with complete re-circulation of cyanide solutions. In this process recovery of 54% Au, 45% Ag, 30% Cu and 50% Zn has been achieved.

Jan 1, 2014

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012