Search Documents

By M. Fafard, M. Dupuis, P. Goulet, J. Bédard

Start-up of a Hall-Heroult cell is a delicate task that can affect pot performance and pot life. Modem practices for high amperage cells involve preheating the lining before the molten electrolyte is poured in. Different preheating methods and heat-up schedules are used throughout the industry, and the optimum between a short start-up and damage minimization to the cell is elusive. Direct electrical coke-bed preheating is one of the most common techniques. This practice typically results in a non-uniform surface temperature distribution and can generate detrimental thermal gradients in the cathode blocks. Numerical modeling is an invaluable tool to study this complex problem and can help improve the preheating procedures. The modeling of the mechanical response of the lining is critical to detect risks of cathode block cracking or the development of gaps where liquids could leak into. Taking into account the baking of ramming paste, the quasi-brittle nature of carbon and the contact interfaces between different materials are examples of key elements to consider. A finite element slice model of a cell was built and simulations of different electrical preheating scenarios were performed using the inhouse code FESh++ to demonstrate what can be learned through thermo-chemomechanical modeling. The potential industrial application of the model is discussed.

Jan 1, 2006

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By Helfried Nafe

"For about a century thermodynamically absurd facts have been propagated in conjunction with the iron-carbon phase diagram. These facts concern fundamental relationships of chemical thermodynamics. Attention is turned here to the discussion of only one of the relevant aspects of the subject, i.e. the definition of the thermodynamic activity of the solute and its implications for the iron-carbon solution.IntroductionThe view on the iron-carbon solution is characterized by the assumption that the solute may appear in two different forms, i.e. graphite and cementite. Accordingly, two carbon solubilities are differentiated, on the one hand for graphite and, on the other hand, for cementite. As a consequence, two versions of the phase diagram exist simultaneously, the application of which depends on the prevailing conditions, (i) the so-called stable phase diagram with graphite as solute and (ii) the metastable one that is based on the cementite-in-iron solution. These diagrams are joined together in the double phase diagram that originates from Heyn [l ], with the first ideas mainly going back to Stansfield [2] and Charpy [3].Thermodynamically, the most inadequate implication of the Fe-C double phase diagram is that the carbon activity may take values larger than unity. With the standard state of the activity being that of the pure substance, i.e. the Raoultian one, such a value implies the nonsensical existence ofa state purer than pure. The explanation of this physical state, ifthere is any, vaguely refers to supersaturation and, in the wider sense, to the physico-chemical phenomenon of metastability. Other aspects of chemical thermodynamics are likewise involved. Therefore, the comprehensive investigation into the present subject requires more topics to be considered than only one separate issue. Not only should the criticism of the present view be in the focus but also the discussion of new ideas capable of reconciling the experimental facts, known about the F e-C system, with the fundaments of chemical thermodynamics. All this, however, cannot be provided here because of the limited space available. As a consequence, in what follows only a part of the whole problem is under scrutiny, i.e. the definition of the thermodynamic activity and its role for the interpretation ofrelevant experimental facts."

Jan 1, 2014

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectic Sn-Pb) and two types of nickel- based UBMs, electroless Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed. The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples of Sn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By Y. C. Guan

In an attempt to replace the traditional cyanide process of extracting gold, a new technology using ammoniacal solutions has been developed. In this study, the electrochemical behavior of gold in ammoniacal solutions at temperatures above 100°C has been investigated. An electrochemical cell in an autoclave has been introduced to carry out this study. The system consists of a gold working electrode, a platinum counter electrode, and an external saturated calomel electrode (SCE) which is connected to the autoclave system through a Birch wood plug. Techniques used in this study included potentiodynamic polarization, galvanostatic polarization, cyclic voltammetry, and Tafel polarization. The electrochemical reaction mechanisms governing the dissolution process are presented.

Jan 1, 1996

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By N. Can

Kinetics and mechanism of the chemical interactions between Si3N4 and TiC were investigated by isothermally reacting samples under nitrogen and argon atmospheres at temperatures between 1600°C and 1700°C? The initial composition of the powder compact contained 20, 30 and 40 volume per cent TiC? Kinetic analysis were performed by measuring mass losses and composition of the titanium carbonitride (TiC1-xNx) at predetermined time intervals? It was found that in the Si3N4-TiC system the degree and rate of the reactions increased with increasing temperature and content of TiC in both nitrogen and argon atmospheres? Si3N4 in the presence of TiC was stable in nitrogen atmosphere and the reactions were confined to Si3N4/TiC and TiC/N2 interfaces? At both interfaces interchange reaction occurs by simultaneous diffusion of nitrogen towards the centre of the particle and desoprtion of carbon in the opposite direction resulting in formation of titanium carbonitrides with various compositions? Reaction products under nitrogen atmosphere were B-SiC, TiCl1-xNx and N2? The maximum "x" value in TiC1-xNx was found to be 0?67 under nitrogen atmosphere? Si3N4 was found to be unstable in argon atmosphere in the presence of TiC and dissociated into liquid silicon and nitrogen gas within approximately four hours of reaction time, depending on temperature? The reaction mechanism in the initial stages of the interaction between Si3N4 and TiC under argon atmosphere proceeds similar to reactions under nitrogen atmosphere? However, considerable amount of Si3N4 dissociates within the first half hour? Liquid silicon aggressively attack both TiC1-xNx and unreacted or partially reacted TiC particles through cracks and pores and diffuses into interier part of the particle forming liquid solutions? After this stage, reactions under argon atmosphere proceeded according to Si-Ti-C ternary system?

Jan 1, 1999

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectie Sn-Pb) and two types of nickel- based UBMs, electro less Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case 'of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed, The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples ofSn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By Swati Mohanty

Spiral concentrator, which works on the principle of gravity separation, is widely used in the mineral industries for separation of solid particles based on the size and density. In the present study, CFD simulation of the flow profile on a laboratory scale spiral concentrator of height 2.29 m, pitch 0.435 m and width 0.17m was carried out. A single computational domain covering the entire spiral was considered. Volume-of-Fluid algorithm was used to track the interface and predict the flow profile. In the present study the Donor-Acceptor method was used for the calculation of volume fraction in the cell. Simulation results show that the velocity increases as the water flows down due to the convective force and gravitational force, but the viscous force acting in the opposite direction retards the flow. Thus the maximum velocity is attained at turn three at which the viscous force overpowers the other forces and further down the velocity decreases. Measured water depths along the radius of the spiral at various heights were compared with simulated depths, which were in good agreement. The simulated liquid phase velocity profile was used to carry out preliminary studies on the flow profile of solid particles of size 500 micron and densities 2600kg/m3 and 5100kg/m3, based on the Lagrangian model taking into consideration fluid-particle interaction.

Sep 1, 2012

By J. S. Kirkaldy

A theoretical procedure is demonstrated for calculating two-dimensional binary cellular single-valued interfaces and extended to triple-valued (remelt) shapes. The numerical calculations for the single-valued local equilibrium problem which yield unique shapes as functions of the supersaturation parameter a and the partition coefficient k are reviewed. The cell amplitude L and wavelength A scale identically as the inverse velocity to the 112 power and the aspect ratio r is a constant equal to 312, independently of a and k for a < 0.5.. For 0.5 < a < m, L, A and r decrease asymptotically to zero indicating the finite amplitude nature of the instability at a = 1 and the existence of sub-marginal states which converge to a flat interface at a- m (Glv- m). Scaling comparisons between equilibrium single-valued and triple-valued and deep-rooted non- equilibrium cells are made.

Jan 1, 1992

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By Jonathan D. Aubertin

The unique nature of rock salt blasting is compared to traditional hard rock practices. Rock salt geomechanical nature is discussed in the context of rock blasting events. A cratering mechanism prevalent in soft rocks is presented and exemplified through a series of single hole blast tests performed in salt deposits.

Feb 1, 2020

By Paul M. Tyler

MUCH has been said in print, and much more that was unprintable, about burdensome controls, taxation, and multiplying restrictive, regulatory, or taxing activities of the Federal Government, but not so much has been said about ways and means whereby the Government can and does render economic assistance. Economics has been defined as the study of men earning a living, and economic assistance to industry as well as to individuals properly should take the form of helping enterprisers to help themselves rather than charity. Proposals to have the Government play Santa Claus must be examined carefully if -only to avoid undue favoritism to politically important persons and downright venality by potentially crooked public officials. Thomas Jefferson is credited with the remark that the best government is the one which governs least. Paternalism is abhorrent to most Americans.

Jan 1, 1947

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot&apos;s reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.&apos;&apos; The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

By Daniel Maine

Swelling clay soils have been problematic to many types of infrastructure in the United States. However, their impact on underground construction is often misunderstood. The use of swell pressures in design of initial tunnel and shaft support lacks proper guidance and is often mis-interpreted. This paper provides insight and guidance on how to implement a geotechnical investigation program to determine if swelling soil exists at a site and how it impacts the design of temporary support systems for underground projects. An example is provided for how swell pressures were incorporated into the design of an initial support system for a rib and lagging tunnel system and problems that occurred.

Jun 23, 2024

By Peter Faust

"The south access road to San Francisco’s Golden Gate Bridge, known as Doyle Drive or Presidio Parkway, needs to be replaced. Built in 1936, it is the primary highway and transit linkage through San Francisco between counties to the north and south. The roadway is tucked into the natural contours of the Presidio and the Golden Gate National Recreation Area, one of the nation’s largest urban parks.The old steel truss structure will be replaced by a new concrete cast-in-place bridge. The foundation design of the new bridge is based on drilled mono shafts below each bridge column. Most shafts required large diameter permanent steel casing installed under strict vibration limitations since several historic landmarks are near the project alignment. Malcolm Drilling decided to use the largest oscillator in the world to install the piles.The area occupied by the Presidio is generally hilly, sloping down northwards to San Francisco Bay. In the western half of the project route, two bluffs rise steeply to about 80 ft (25 m). The bluffs are separated by a valley 60 ft (18 m) deep and 1,500 ft (457 m) wide, which is spanned by the old and new bridge. Overburden soils in this valley are made up of artificial fill, slope debris, ravine fill and Colma Formation, a fine to medium-grained sand unit with clay beds. The Bay Muds encountered in the project area are typically soft clayey silts, becoming medium stiff with depth.The basement rocks underlying the overburden belong to the Franciscan Formation, described as shale, sandstone, serpentine and greywacke, it is extremely variable in hardness, fracturing and weathering. The material can vary from very hard to very soft, can be slightly to very intensely fractured and almost not weathered, to totally decomposed within relatively short distances both laterally and vertically. Rock strength can vary from too weak to be tested to serpentine layers with unconfined compressive strength of 15,000 psi (103MPa) or higher. Groundwater levels in the area are typically no more than 10 to 20 ft (3 to 6 m) below the ground surface."

Jan 1, 2012

By Yashar Pourrahimian, Magreth S. Dotto

Fragmentation by blasting is a critical process in hard rock mining. The blasting process and outcomes are highly influenced by rock mass properties and their response to higher stresses and loading rates. Each rock mass is unique, but some features affect the blast energy similarly, leading to similar outcomes. Having analyzed these features and their influence on blast results, they can be incorporated into the blast design to achieve better outcomes. This paper presents a numerical model validated by a case study from the actual mine blasts that studied the effect of rock mass properties on explosive energy production, attenuations, and overall blast outcomes. The results show that when the model parameters are calibrated based on real data, they can be used to simulate the fragmentation process and therefore be used to aid blast design.

Jun 25, 2023