Search Documents

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer's estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By David V. Lewin

Heavy structures in central Cleveland, Ohio, are supported on raft foundations, driven piles, or caissons. Settlements can be predicted and structures are designed to accommodate such settlements. On one project the settlements were not provided for in the design of the structure. Soils are sands, silts, and varved clays to shale. A rift in a central area is 600 feet deep. Solutions to problems, and results, are detailed.

Jan 1, 1985

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By J Williamson, M Griessmann

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Watershed tungsten deposit is located in the Hodgkinson Province of north Queensland, Australia. The deposit is hosted by Siluro-Devonian flysch-type meta-sediments of the Hodgkinson Formation, which were subjected to four major deformation events. Mineralisation has occurred syn- to post-D4 and is related to the intrusion of S-type granitoids of the Permian Whypalla Supersuite.Watershed is located within a regional NW–SE-striking melange zone composed of brecciated and intermixed arenites and shales. The major NW–SE-striking Tullah fault zone is situated in close proximity to the east of the deposit.The Watershed deposit occurs within a tightly folded upright anticline with NW-plunging fold axis. The anticline contains a major package of coarse-grained to conglomeratic arenite, which harbours the Watershed mineralisation. Several alteration styles occur within the arenites, of which Fe-poor calc-silicate alteration dominated by clinozoisite/epidote is the most significant. Less widespread but locally important alteration styles comprise garnet-dominated calc-silicate alteration, albitisation and sericitisation. The arenites are enveloped by unmineralised carbonaceous shales and shale breccias.Tungsten mineralisation occurs solely as molybdenum-poor scheelite and can be found as three styles: disseminated mineralisation in calc-silicate altered arenites, vein-style mineralisation with quartz-albite-scheelite veins and minor but high-grade mineralisation in albitised felsic dykes.Contact metamorphic rocks and geophysical data indicate the proximity of an underlying granitic body. It is believed that this granitic body was the main driver of the hydrothermal system generating the Watershed deposit. An early mineralisation stage caused the selective calc-silicate alteration of the arenites, while a second stage caused the vein-style high-grade mineralisation. The folded shales enveloping the arenites worked as an effective barrier that kept the mineralising fluids in a confined rock volume.The scheelite mineralisation at Watershed is open to depth, with a granite-hosted porphyry or greisen-style mineralisation anticipated below the current resource.CITATION:Griessmann, M and Williamson, J, 2015. The calc-silicate-hosted Watershed tungsten deposit, far north Queensland, Australia , in Proceedings PACRIM 2015 Congress, pp 545–550 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Fredrick D. Palmer

The World is Turning to Coal Peabody?s View ?We believe the world is increasingly energy-short, led by unprecedented demand from population centers and economic hubs in Asia, the Middle East and South America ?This occurs as:?Traditional energy sources are clearly constrained, requiring coal-based alternatives?Energy-rich nations leverage political gain from their assets, and nations urgently look to improve energy security ?In this environment:?Oil, coal and gas face a greater long-term convergence, ?Coal?s traditional regionalized nature becomes global, and ?Coal?s compact energy form becomes an attractive source for liquids and substitute natural gas ?The world is blessed with an abundance of coal to help meet all human energy needs

Jan 1, 2008

By Kevin Andrews, Terry Hamric, Scott Nelson

"Mining conditions in underground coal mines are dictated by the environment in which the coal seams were geologically deposited. Depositional features can change rapidly, significantly affecting mining conditions. Mine geologists understand factors affecting mining conditions, predict future conditions, and provide guidance to mine management. A case study demonstrates how a mine in Appalachia merged an understanding of depositional environments with mining conditions and drilling data to make informed decisions as the mine encountered geologic anomalies. The assessment included drilling, mapping of geologic hazards and mine productivity, and creation of a conceptual depositional model. Metallurgical coal quality and clean tons per foot served as incentives for continued advance. Mining in the south was historically favorable, with good production and advance rates. As mining advanced north, changing geologic conditions caused the upper seam split to abruptly disappear. The mine ramped down into the lower seam split. Mining in the north area encountered unfavorable conditions, including transition roof, “horsebacks,” sandstone intrusions, roof rolls, and bony floor, resulting in low rates of mining advance. The mine geologist characterized the features and created a predictive model for future mining. Most of the adverse conditions were attributed to the coal in the north being part of an incised, transgressive valley fill environment, as compared to the favorable conditions in the south resulting from a floodplain depositional environment. Geologic conditions, low productivity, and unfavorable future predicted conditions in the north ultimately resulted in mine closure and reallocation of resources to a new mine with better forecasted conditions.INTRODUCTIONThe role of a geologist in assisting coal mining operations to understand and predict the impact of varying geological factors on mining productivity is a critical one, especially when management decisions must be made about the future prospects of a mine operating in difficult conditions. Chase, Newman, and Rusnak (2006) provide a very thorough discussion of the evolution of the role of the coal mine geologist and emphasizes the importance of understanding geology with regard to mine management decisions. Using actual mining performance data to determine which geologic factors are the most critical for mining is a powerful tool for making informed mine management decisions. For example, Nelson, Mullennex, and Miller (1988) provide a case study of analyzing the geologic factors impacting productivity of a Kentucky longwall mine to predict future mining conditions for the operation. In that case, the difficult geologic factors for longwall mining were prevalent across much of the remaining permit area and, in response, mine management converted the operation from a longwall operation to a continuous miner (CM) operation to better adapt to the geology. In another example, Keim and Miller (1999) evaluated geologic conditions impacting a West Virginia longwall mine. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed. Numerous examples of advanced Geologic Hazard Mapping (GHM) methodologies have come from government agencies and academia. For example, development of the Coal Mine Roof Rating (CMRR) system (Molinda and Mark, 1994) provided a standard means for geologists and engineers to communicate quantitatively with regard to mine roof conditions, and the introduction of the Stability Mapping System (SMS) provided an efficient means for analyzing numerous factors affecting coal mine stability (Wang and Heasley, 2005)."

Jan 1, 2019

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

Currently in Canada there are 15 major mining companies with a minimum of $1 billion in market capitalization or net private value. This group forms the core of an important sector for Canada. The mining sector had gross revenues of about $35 billion in 1988. This compares to a Canadian GDP of $410 billion in 1988. There are at least three different sub-groups within the mining group, each facing the future with very different prospects for the coming years.

Jan 1, 1989

By Leonard Obert

[Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillars, arches, and other structures. Tin r Loa required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E V2d .....(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.]

Jan 1, 1940

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By Leonard Obert

Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillar, arches, and other structures. The method required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E = V2d ...(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.

Jan 1, 1940

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

This study explores two evolving 3D surveying technologies, photogrammetry and laser scanning, and applies them to deformation monitoring of rock faces and mine highwalls. A quantitative analysis focused on 3D coordinate determination is performed. Furthermore, a qualitative assessment directed at the practicality and viability of each system operating near a rock face or in a mining operation is undertaken to reveal one systemÆs deficiencies over the other. Two photogrammetric and four laser scanning surveys aimed at optimising accuracy and precision within a short period of data acquisition are conducted on the rock face at Organ Pipes National Park, Keilor, Victoria. The accuracy and repeatability of each survey is determined using a combination of iWitness photogrammetric, and Cyclone laser scanning software. The 3D coordinates of targets placed on the rock face are determined by triangulation and resection principles within a bundle adjustment. The coordinates determined by each system are then compared in a 3D transformation. Controlled deformation conditions are established to determine the precision to which each system can detect movement in the rock face. An object of known dimensions is placed on the rock face to simulate deformation. The relative orientation of images taken for the pre- and post-deformation photogrammetric surveys provide an overall 3D point accuracy of 1.255 mm and 1.804 mm respectively. A 3D transformation shows discrepancies of less than ¦22 mm (RMS) between the geometry of the photogrammetric and laser scanning models. Both systems are able to detect the simulated deformation to a precision of 50 mm. This work also identifies how to obtain millimetre accuracy for 3D coordinate determination of rock faces, thereby providing a quality data set for surveyors, geotechnical engineers and mine geologists. Photogrammetry is shown to be a mobile, time and cost-effective technique that is more amenable to mining operations than terrestrial laser scanning. However, both systems demonstrate that they are capable of detecting movements that may lead to failures in the rock face, and possibly endangering human life. The implications are significant for surveyors, geotechnical engineers and mine geologists working in mining operations where enhanced safety conditions, increased productivity and lower operational costs are important considerations.

Jan 1, 2009

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.' Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By H. Tomlinson

"INTR0DUCTIONThis publication is a third of a series devoted to falls of roof and coal in coal mines of the Western States. It gives the results of examinations of the mines of the Rock Springs coal District of Sweetwater County, Wyo., which represent the principal coal beds therein and approximately 75 percent of total production of the State.A study was made of safety conditions at all the producing mines of the district and suggestions were offered the operators regarding methods and practices which would, in the opinion of the writer, provide additional safeguards to prevent accidents from falls of roof and coal.In presenting the subject, consideration must be given to such features as character of the coal beds, depth of cover. methods of mining, timbering practice, roof testing and supervision, and for comparative purposes to certain statistical matter bearing upon relation of accidents to their causes, tonnage produced, men employed, days worked, and lost days due to accidents during the 3—year period covered by this study.ACKNOWLEDGMENTSThe writer acknowledges the cooperation of the officials of the various coal companies, without whose assistance this work could not have been completed.F0UR REPRESENTATIVE COAL OPERATIONSThis report relates to four representative coal operations in the Rook Springs district of Sweetwater County, Wyo., which are referred to as mines A, B, C, and D. This group employs yearly an average of 993 men, representing 37 percent of the men in coal mines of the county, and has an average annual production of 1,484,373 tons, representing approximately 44 percent of the coal produced in the county. Figure 1 is a map of the Rook Springs coal district."

May 1, 1933