Search Documents

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By V. R. Miller

The Bureau of Mines investigated methods for testing the tensile and sheer strength of cast specimens of bulk solder and of soldered joints in order to increase the strength and extend the useful temperature range of soft solders. A spread-area test for determining the wettability of solder on copper surfaces was developed. Mannitol was used as a flux in spread tests to control spreading and to avoid plating, etching, and other side effects of regular fluxes. Data on commercial and high-purity solders obtained by these methods show more consistency than those reported by others from similar tests.

Jan 1, 1967

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By J. R. Rau

While refuge chambers are common place in most underground mining projects, there are different philosophies as to what life support systems are to be considered and how these systems are to be applied. Case studies in the underground mining industry have examples of emergencies where the external compressed air and power supply to the refuge chamber were compromised due to proximity of services to the fire location. In 2005, The Department of Industry and Resources, Western Australia, drafted guidelines that listed specific requirements for refuge chambers which included a secondary life support system that would operate independently of external sources. The objective of this document is to examine what critical life support systems are essential for safe entrapment in the event of an emergency and to examine considerations for their application.

Aug 1, 2013

By Jan M. Mutmansky

"When, in 1973, a limit was placed on the amount of dust in the coal mine atmosphere, restricting the average exposure of a coal miner to 2 milligrams of dust per cubic meter of air (mg/m'), skeptics in the United States and abroad Said the standard could never be achieved. They cited much more lenient standards already established in other countries and refused to believe that the United States could meet the world's most stringent requirements in mines where dust had never before been regulated. Yet 10 years later the goal had largely been achieved and miners were working underground in a cleaner atmosphere than ever before. It was a major achievement and a big stride in what had become a war on coal workers' pneumoconiosis (CWP), the black lung disease prevalent among miners in underground coal mines.Although the health hazards caused by working in a dust-filled mine atmosphere have long been recognized, the problem became particularly acute in this century with the mechanization and increased productivity of underground coal mining. The United States was much slower than some other countries to address the problem of respirable diseases among miners. While dust levels in South African gold mines were first regulated in 1912, in the United States it was only when 476 workers died of silicosis while blasting a tunnel through a mountain near Gauley Bridge, West Virginia in the 1930s that widespread public attention became focused on the plight of workers in dust-filled environments. Another 30 years passed before regulation of dust finally became law in the Coal Mine Health and Safety Act of 1969.With a stringent new standard imposed in all underground coal mines, the industry was faced With the daunting problem of reducing levels of airborne dust from perhaps 6.5 mg/m' to 2 mg/m', in an inherently dusty operation carried out in the close confines of underground passageways. Most of the coal dust is made by the cutting operation in which the continuous miner or longwall machine can produce several thousand milligrams of respirable dust for each ton of coal mined. Other dusty operations such as drilling holes for roofbolts, loading and unloading coal on shuttle cars, and the operation of conveyor belts contribute to the overall problem.Since the institution of the new dust control standards, a number of strategies have been adopted for reducing the coal dust in the mine atmosphere. These strategies involve engineering and design improvements that help lo prevent the generation of particles, keep particles of dust from becoming airborne, carry dust away from the working area, and isolate the dust from the workers in the mining operation. These procedures have been pursued vigorously by the Bureau of Mines, and many successful methods have been developed to reduce the mass concentration to which the workers are subjected. The mining companies were reluctant at first to confront the problems but after a period of trials and gradual improvement, they joined with others in the fight to reduce the dust concentrations in the working place."

Jan 1, 1990

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By Neil D. Donnell, O&apos

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely-spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an ore body block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1985

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM's structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By G. Scamans, J. Lazaro-Nebreda, Z. Fan, J. B. Patel

"Melt quality is crucial for both continuous and shape casting of light alloys and in order to improve it, removal of excessive inclusions, accumulated impurities and unwanted gases becomes necessary. To address this problem, a new multi-purpose high shear liquid metal treatment technology, based on intensive melt shearing by a rotor/stator unit, has been developed. The device ensures achieving uniform temperature and chemical composition and an efficient dispersion of gas and solid phases in the melt with minimal disturbance of melt surface, and can be used, among other things, for de-gassing and de-ironing of Al-alloy melts. Efficient degassing is achieved by dispersing each argon bubble into many small ones, which significantly increases the overall surface area of the bubbles and the time they remain in the melt capturing hydrogen before reaching the surface. This allows using much lower inert gas flow and mixing times than conventional rotary degassing. When applied to Al-alloy scrap, with accumulated iron, the high shear melt treatment speeds up the nucleation and growth of primary Fe-rich intermetallic particles, allowing a faster removal rate. Therefore it reduces processing times, increasing recycling productivity, and facilitates full metal circulation of secondary Al-alloys.INTRODUCTION Aluminium and magnesium alloys are widely considered in various industrial sectors for the purpose of weight saving (Polmear, 1995). In particular, they are used in the automotive sector, where components are mostly manufactured by high pressure die casting (HPDC) because of its simplicity and relatively low cost, but efficiency and mechanical properties are quite low compared with other processes. To date, the main focus to overcome this problem has been for improving the HPDC machinery (Dahle, 2001) but little attention has been paid to the opportunities of controlling the nature and quality of the molten metal supplied to the die. In this way, liquid metal treatment, which involves a variety of physical and/or chemical processing methods to improve melt quality prior casting, is crucial for both continuous and shape casting products."

Jan 1, 2018

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957

By L. Adler

To mine safely and efficiently the working conditions must be systematically de¬fined. Their uniqueness distinguishes mining from other engineering professions. The worst case in underground mining is delineated and termed "encumbered space'", since it "seriously impedes motion or action." Working space is inherently hazardous, transitory, and expensive, inducing it to be of low quality, tight and congested, vulnerable and deteriorating, and isolated and inaccessible. These adverse conditions, are damaging to cumbersome, mobile equipment, and affect all activities, including surface work. The conditions are reorganized using the fundamental engineering dimensions: space, matter time, people, and money. Comprehensive tables are presented with attention paid to "disaster potentials". Examples are cited.

Jan 1, 1982

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By A. G. Nitschke, I. Ossenbühl, W. Dolsak, J. Dase

"The authors have successfully developed an innovative rehabilitation concept, which meets actual technical standards and minimizes the impact on the operation of a key conveyor tunnel. A flexible and stepwise ground support rehabilitation program utilized a combination of yielding steel arch sections with grout filled fabric hoses, which represents a fast and safe backfilling support system. The system was developed and successfully installed at Bingham Canyon Mine, the world’s largest open pit copper mine, which also includes numerous underground structures. The mine is owned and operated by Kennecott Utah Copper (RTKC) a fully owned subsidiary of Rio Tinto. The system was implemented at a conveyance tunnel, which was originally designed as a railroad tunnel, but was re-commissioned and is currently used as a conveyor belt tunnel to transport ore from the open pit to processing facilities outside the mine. The existing structure showed signs of overstressing due to movements in the surrounding rock mass, which had to be addressed with a yielding support system in order to provide safe access into the tunnel. However, the impact on the conveyor belt operation due to support installation was to be limited to the bare minimum. Keywords: rehabilitation, yielding support, mining, stabilization, and grout filled fabric hose.PROJECT DESCRIPTION The C6 Tunnel is considered a critical asset for the operation of the Bingham Canyon mine as it comprises the standard route for transporting crushed ore from the open pit to the processing facility on a continuous conveyor belt system. The C6 tunnel was originally built as a railroad tunnel. Construction was completed in 1959. The original horse-shoe shaped cross section of the tunnel was 18 feet wide and 24-1/2 feet high [8]. The tunnel length was approximately 18,000 feet. During its service life, the railroad tunnel has undergone several transformations. The length of the tunnel towards the Bingham Canyon pit was shortened over the course of mining operations and the railroad tracks in the tunnel were removed. The invert was partially backfilled (3 feet typical) and a 72 inches belt conveyor was installed. Currently, the C6 Tunnel is nominally only approximately 21 feet high and 15,000 feet long. Ground Support and Rehabilitation Measures prior to 2014 The C6 tunnel was mined mainly with conventional mining methods, using drill & blast as the typical one. However, the weak geological sections, such as those encountered in the Fortuna fault, were excavated by shaping and chipping with machine-held moils [8]."

Jan 1, 2015

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992