Search Documents

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K's) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.' In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By W. C. Williamson, J. L. Shugert

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By C. Kremer Bain

UNDER present economic conditions the necessity of mechanizing the mines of our country has become a very important problem. More and more mines are looking toward increased or complete mechanization of their operations, so in the writer's opinion it is quite pertinent that some of the associated problems that accompany such a program be pointed out. The following generalization on attempting a comparatively slight change in mining methods at the Southeast Missouri properties of the St. Joseph Lead Co. is an attempt to point out to anyone faced with a mechanization program that much time and C. KREMER BAIN, Member AIME, is Assistant to General Manager, St. Joseph Lead Co., Bonne Terre, Mo. AIME Sun Francisco Meeting, February 1949. TP 2743 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Dec. 27, 1948; revision received Oct. 13, 1949. effort can be saved, and many headaches avoided, if company policy can be established whereby everyone in the organization from the top down is desirous of improvement and is working towards the common objective. Any changes in mining methods, machinery, and so on, must entah coordination of all the other phases of mining as they all have to mesh as accurately as a smooth running chain of gears if satisfactory results are to be obtained. The purpose of this paper is to point out some of the problems which :have to be surmounted when any mechanization program is attempted, rather than to go into the mechanical details and actual operating data of the equipment employed. After all, machines have to be adapted to best suit the local conditions, so no general formula can be given that would apply to other properties. Although St. Josepll Lead Co. has been mechani-cally-minded for a number of years, as shown by the fact that over 110 million tons have been loaded mechanically since 1922, any further mechanization or changes always present a problem. When our ore bodies were of great height and area the breaking and loading were developed to a high degree of efficiency according to known standards. But in recent years, when our ore bodies became smaller and more scattered, the amount of tonnage we were able to break was not sufficient to supply our shovels with enough rock to keep them working to capacity. Our first step in attempting to rectify this situation was to develop a technique of moving the shovels to the broken ore in various stopes, which sometimes entailed a move each shift. A shovel is not producing when being moved, so within the last two years we have been endeavoring to devise some means of getting more rock broken in these smaller stopes and it was then that we became interested in jumbo drilling. To illustrate the fact that mechanization is a process of a chain of developments rather than a stroke of genius can best be shown by a general summary of conditions and obstacles which were encountered in our present attempt to establish template drilling of a standardized round. Our first jumbo was more or less the conventional type with two machines mounted on a crossbar. This arrangement proved to be impractical to duplicate satisfactorily the regular routine of slabbing in a more or less radial pattern as carried out by column drilling. One machine was either too close to or too far from the face and there was another disadvantage in that one drillman was frequently delayed while waiting for his partner to bottom a hole. Our next step was to eliminate the crossbar so the machines could operate independently of each other, but we still encountered the same objections mentioned above except that one drillman was free to drill three holes instead of one in a vertical plane independently of his partner. Time studies while trying to adapt the jumbo to the regular slabbing practice as accomplished by column drilling, revealed that twice as much time was spent in maneuvering the jumbo into position and aligning the holes as was consumed in drilling.

Jan 1, 1951

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By John S. Crandall

THE mineral garnet, while ordinarily considered a semiprecious gem stone or a second-grade industrial gem, has also proved itself in the field of industrial abrasives. Its use is well known as a sandpaper grain, and as a sandblasting sand its qualities are rapidly becoming recognized in more and more industries. Production of garnet as an abrasive is confined chiefly to two areas in the United States, North Creek, N. Y., where the Barton Mines Corp. operates, and Emerald Creek, Benewah County, Idaho, where Occurrence: Garnets in the Emerald Creek area occur as disseminated crystals in beds of micaceous schists of the Belt Series, which in this section are estimated to be close to 4000 ft thick. The schists are high in alumina and silica with iron, manganese, and magnesium. Subjection of the original sediments to high temperatures and pressures caused metamorphism to take place with the resultant re-crystallization of high alumina-silica minerals such as garnet, mainly spessartite and almandite varieties, cyanite, sillimanite, chlorite, actinolite, tourmaline, biotite, and muscovite, with minor amounts of ilmenite and magnetite. Quartz is also present in considerable amounts. Fast erosion of the soft mica schists on exposure to weathering has created extensive alluvial deposits containing up to 10 pct garnet having a maximum grain size of 3/16 in. These alluvial sands and gravels are now being treated for the recovery of garnet sands. Treatment: Overburden of 1 to 4 ft must be stripped to expose the garnetiferous gravels. This operation and the subsequent feeding of the gravels to a trommel-screen washing plant are performed by a % yd dragline. The trommel-screen openings are 3/16 in., thus allowing a separation and concentration based on grain size, since over 95 pct of total free garnets are minus 3/16 in. All plus 3/16-in. material is wasted at this point. The minus 3/16-in. material is further concentrated in a sand-drag classifier, where the slimes and silts are washed out and wasted. The sand product from the classifier varies in garnet content from 20 to 60 pct according to the particular section of ground being worked. This sand product is trucked to a jig plant where two sized fractions are made in a trommel-screen. The minus 3/16-in. plus 10-mesh portion is fed to a Pan-American two cell 42-in. jig. The minus 10-mesh portion is treated in a Bendelari three cell 42-in. jig. The jig concentrates are combined to form a 98 pct garnet sand. The jig tailings contain 3 to 5 pct garnet which is mainly flat crystals and chips which will not settle into the jig hutch. Subsequent treatment of these tailings in a scavenger jig followed by drying and electromagnetic separation will, according to tests, reduce the garnet losses in the tailings to something around 1 pct. Jig treatment of this feed approaches ideal as the major portion of the garnet crystals are the natural dodecahedrons and so are, in general, close to spherical. The specific gravity of pure garnet is 4.2, while the next heaviest mineral in the feed is cyanite with a specific gravity of 3.6, then quartz with specific gravity of 2.6. The garnet concentrate is practically free of quartz. The predominant impurity is cyanite which amounts to about 1.5 pct. The rod-like crystals of cyanite appear to up-end in the jig and go into the hutch with the garnets. Some ilmenite and magnetite appear in the concentrate but in very minor amounts. Subsequent washing in a sand-drag classifier removes fine silts and iron oxides. The gravel feed to the washing plant will average 8 pct recoverable garnet content. Concentration ratio in this plant runs about 2.5 to 1. Washing-plant concentrate as fed to the jigs will average 45 pct garnet by weight. Concentration ratio of jigging runs about 2.2 to 1. The garnet concentrate is dried in a rotary oil-fired drier and then fed to vibrating screens in closed circuit with crushing rolls. Practically any grit from 10-mesh down to 150-mesh grain size may be graded to specifications in two 3-deck vibrating screens. The present production, however, is approximately 75 pct No. 36, 15 pct No. 60. and the balance No. 80 and No. 100. Metal-screen cloth is used for sizes down to 36 mesh. From 36 mesh and finer, silk-screen cloth is used since it has less tendency to blind. All garnet sand is bagged in 100 lb self-sealing, sleeve-type paper bags. Practically all shipments are made in carload lots. Car loading is convenient since the plant is in Fernwood on the tracks of a branch line of the Milwaukee railroad. Truck shipments can and are made occasionally.

Jan 1, 1951

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By Frank G. Miller

This report presents developments of fundamental equations for describing the flow and thermodynamic behavior of two-phase single-component fluids moving under steady conditions through porous media. Many of the theoretical considerations upon which these equations are premised have received little or no attention in oil-reservoir fluid-flow research. The significance of the underlying flow theory in oil-producing operations is indicated. In particular, the theoretical analysis pertains to the steady, adiabatic, macroscopically linear, two-phase flow of a single-component fluid through a horizontal column of porous medium. It is considered that the test fluid enters the upstream end of the column while entirely in the liquid state, moves downstream an appreciable distance, begins to vaporize, and then moves through the remainder of the column as a gas-liquid mixture. The problem posed is to find the total weight rate of flow and the pressure distribution along the column for a given inlet pressure and temperature, a given exit pres5ure or temperature and given characteristics of the test fluid and porous medium. In developing the theory, gas-liquid interfacial phenomena are treated. phase equilibrium is assumed and previous theoretical work of other investigators of the problem is modified. Laboratory experiments performed with specially designed apparatus. in which propane is used as the test fluid, substantiate the theory. The apparatus. materials and experimental procedure are described. Comparative experimental and theoretical results are presented and discussed. It is believed that the research findings contributed in this * paper should not only lead to a better understanding of oil-reservoir behavior, but also should be suggective in regard to future research in this field of study. INTRODUCTION In recent years much time and effort has been consumed in both theoretical and experimental studies of the static and . dvnamic behavior of oil-reservoir fluids in porous rocks. Although lack of sufficient basic oil-field data, principally concerning the properties and characteristics of reservoir rocks and fluids, largely precludes quantitative application of research results to oil-field problems, qualitative application has become common practice. In effect. oil-reservoir engineering research is serving as a firm foundation for oil-field development and production practices leading to increased economic recoveries of petroleum. This province of research. however, still poses many perplexing problems. The thermodynamic behavior of two-phase fluids moving through porous media constitutes one facet of reservoir-fluid-flow research that has not received the attention it deserves. This report embodies a theoretical discussion of this subject and a description of a series of related laboratory experiments. The significance of the problem to oil field operations is indicated but in articular the report centers around a theory and method for analyzing the steady. macroscopically linear, two-phase flow of a fluid (a single molecular species) through a horizontal column of porous medium. For simplicity in showing how the thermodynamic behavior of two-phase fluids moving through porous media affects oil-reservoir performance problems, attention is focused temporarily on a particular well producing petroleum from an idealized water-free solution-gas drive reservoir, the reservoir rock being a horizontal, thin, fairly homogeneous sandstone of large areal extent confined between two impermeable strata. The flowing hydrocarbon fluid is considered to exist entirely as a Iiquid at points in the reservoir remote from the well; however. the decline in fluid pressure in the direction of the well causes vaporization of the hydrocarbon to begin at a radial distance r from the well. Upstream from r the fluid moves entirely as a liquid and downstream from r it moves either entirely as a gas or as a gas-liquid mixture depending on the properties of the hydrocarbon and on the thermodynamic process it follows during flow. The distance r would be variable under transient flow conditions. but for purposes of analysis the flow is considered to l~e steady at the particular instant of observation during the flowing life of the well of interest. If the flow were isothermal and the hydrocarbon a pure substance, the fluid would be entirely gaseous downstream from r. Thus, this isothermal flow process for a pure substance would require that the heat of vaporization be supplied at r. over zero length of porous medium, at the precise rate necessary to maintain the constant temperature. This means that the solid matrix of the porous medium (reservoir rock) and the surroundings (impermeable strata confining the reservoir rock) would have to serve as infinite heat sources. Heat-transfer requirements would be somewhat less severe for the isothermal flow of a multicorn-ponent hydrocarbon as bubble and dew points at the same temperature correspond to different pressures. In this instance isothermal conditions would be sustained without complete vaporization of the fluid over zero length of porous medium. Nevertheless. as the flow is in the direction of decreasing

Jan 1, 1951

By Walton J. Greer, System By John E. Owen

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.'.' If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951

By Alton B. Cook, G. B. Spencer, F. P. Bobrowski

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.' Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By Elliot P. Rexford

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By William L. Crentz

This study of the preparation characteristics of the coals in Indiana County, Pa., is the second in a series of Bureau publications appraising the Nation's coking-coal reserves by counties and the practicability of upgrading marginal deposits to metallurgical standards. The first publication dealt with the preparation characteristics of the principal coal beds in Cambria County, Pa. Over 95 percent of the coal remaining in Indiana County is in the Upper Freeport, Lower Freeport, and Lower Kittanning beds. Isolated patches of Pittsburgh-bed coal are present, and the Upper Kittanning bed is found in minable thickness at some locations, but production from these sources is not large. The greatest production is from the Freeport beds, which account for nearly 70 percent of the Indiana County coal output. These beds usually contain two or more shale or hone partings and in many places are high in sulfur. The large proportion of bony coal in the Freeport beds 'produces a relatively high-ash product. Mining practices vary from place to place, but it is frequently necessary to leave certain bony portions of the bed in place in order to load a satisfactory product. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1951