Search Documents

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Ernest L. Ohie

In 1939 the Geological Society of America published a summary of the geology of the ore deposits of the Mississippi Valley region, This volume, edited by E. S. Bastin, contained contributions from the foremost students of the area which described theregionalgeologic setting of the various deposits as wel as the detailed geology as then known. The various ideas as to the origin of the ores were discussed with the general, though not unanimous, conclusion that the deposits were hydrothermal products, Only those deposits in the immediate Mississippi Valley area were considered without any attempt to introduce evidence from other districts generally accepted as being of the "Mississippi Valley type." Since 1939, much new information has come from extended studies of two of the important districts described in the 1939 report andimportant extensions of the known ore have been found. Likewise, concentrated geologic efforts have been fruitful in severa "Mississippi Valley type" districts - both U. S. andforeign - not treated in the 939 paper. The wealth of new field information on the structural and stratigraphic relations of this interesting ore type, coupled with the results of theoretical and laboratory studies of the past 18 years, makes desirable a review of our present knowledge and interpretation of these important deposits which for many years have yielded over 20 percent of the world's annual production of lead and zinc, together with large amounts of fluorspar and barite. No restatement of the details of the geologic evidence willbe attempted here; the interested student is referred to the papers cited. Slide No. 1 shows the distribution around the world of the deposits under consideration. A principal thesis of my remarks is that there is so much similarity in all these deposits that it seems necessary for all of them to have had a similar mode of origin, whatever that may be. Variations in the shape, size and mineralogy of the orebodies give each district some individuality, but there are enough of the "typical" characteristics present in all cases to make classification in the "Mississippi Valley type" agreeableto most geologists. Thus the overall process giving rise to the ore solutions surely was the same for all in the group. Either they all have igneous affiliations or they all do not. Acknowledgment of this kinship between deposits in the various districts offers many advantages in trying to arrive at a decision as to just what the origin may have been, for the amount of guiding and limiting evidence which must fit into the hypothesis is greatly increased over that available in any one district, To a certain extent this was recognized by the authors of Special Paper 24 in treating all of the immediate Mississippi Valley areas together; by expanding the consideration to include ore deposits of this type all over the world the changes of success, i.e., arriving at the correct answer, are improved several fold. Since most of these districts are quite simple structurally, a number of hypotheses might fit the facts in any one of them, but if the facts to be met can safely be drawn from all the districts, then the explanations which will fit all the data are much less numerous. One purpose of this paper is to call attention to the field facts that have been reported from the .various areas which seem to have an important bearing on the kind of ore fluid that was responsible for the ore and on the way it circulated.

Jan 1, 1958

By A. R. Harrington

BEFORE discussing some of the technical aspects of the steam generating plants of Nova Scotia Light and Power Company, Limited, it might be of interest to go back through history and see the development of steam generation in this public utility. Back around 1902 Nova Scotia Light and Power Company, Limited, had three slide-valve engines in-stalled at its Water Street, Halifax, generating station for a total capacity of 1,800 kilowatts. The plant remained at about this size until 1910 and in 1911 a 2,000 kilowatt steam turbine was installed to raise the total capacity of the plant to 3,800 kilowatts. In 1916, a 3,000 kilowatt turbine was installed and one of the slide-valve engines was removed to make a total plant capacity of 6,200 kilowatts. The total demand in the Company's service 8rea was at that time 4,000 kilo-watts.

Jan 1, 1958

By A. C. Johnson

The T. L. shaft of the Eureka Corp., Ltd., near Adams Hill, Eureka, Nev., was sunk in 1954 and 1955 to permit exploration and development of the lead-zinc-silver ore that had been indicated by drilling. This paper describes the sinking of the 4-compartment, vertical shaft to a depth of 1,127 feet and includes pertinent details of equipment, methods, and costs. A shaft crew of 10 men, supplemented by 13 hoistmen, topmen, carpenter, and shop crewmen, sank and timbered the 1,127 feet of shaft in 630 workdays. Total labor per foot of shaft was 107.95 man-hours. Supplies per foot of shaft included 20 pounds of explosives, 1.61 pounds of drill steel, and 200 board-feet of timber. Power consumption, including that required for pumping, averaged 3,726 kw.-hr. per foot.

Jan 1, 1958

By M. W. Airth

ON THE 6TH JULY in the year 1953 an announcement was made to the public that touched off one of the greatest staking rushes in the history of mining in Canada and resulted, in tl1e space of a few short years, in the development of the greatest reserves of uranium-bearing ore in the world. It was ?On this date that the famous "Blind River back-door staking bee" was completed with the acquisition of some 2,000 claims by the Preston East Do me-Technical Mine Consultant teams under the direction of Mr. Franc Joubin and Mr. Robert C. Hart. That story has been told from coast to Coast and is too well known now to re-quire elaboration. Suffice to say that, in the short elapsed time of less tl1an five years from that momentous summer of 1953, three of the Algoma mines are in full production, three more are rapidly nearing full production, five more 1are approaching the production stage, a new hard-surfaced highway, 108, has been built to serve the area, and a brand new, completely planned city, Elliot Lake, is being built to provide the amenities of living to the 22,000 people already in the area.

Jan 1, 1958

By Joseph U. Messenger

A method of applying ammonium hydroxide to a drill stem containing hydrogen sulphide gas and hydro-gen-sulphide-bearing oil and water so as to remove the hydrogen sulphide as ammonium sulphide is de-scribed. It was concluded that the method allowed trips with drill pipe filled with sour fluids to be made more safely, more rapidly, and more economically. INTRODUCTION THE DANGER of poisoning rig crews during drill stem tests of sour wells by exposing them to hydrogen sulphide gas is well known in Canada. Concentrations of hydro-gen sulphide in sour gases range from 0 to 40 volume percent. There have been numerous casualties from hydrogen sulphide exposure during drill stem testing. Some have resulted in permanent injuries; in some cases the injuries have been fatal. For example, in Alberta in 1957 there were four deaths and 100 exposures which required medical treatment. These fatalities and injuries indicate the need for a more effective way of handling hydrogen sulphide in oilfield operations.

Jan 1, 1958

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By P. M. Sullivan

Galvanizers' sal skimmings have been treated by two methods of leaching in attempts to produce preflux solutions suitable for use in galvanizing operations. Both water-leaching and acid-leaching procedures are effective, except in severely exhausted skimmings when water-leaching becomes impractical. A preliminary analysis of the skimmings is not required. Solutions in the recommended concentration range can be produced conveniently by control of pH, specific gravity, and chlorine content. A technician would require only a short period of training to be able to perform the operations described.

Jan 1, 1958

By William F. White

It is a pleasure to have the opportunity of being here today to discuss the application of horizontal filters in the metallurgical industries. The use of horizontal type filters has been limited in metallurgical plants. However, in the recent past there have been new designs of this type equipment which greatly broaden their field of application. Through their use in many applications, important economies can be achieved over more conventional methods. The first of the modern continuous horizontal filters was initially developed by Oliver United Filters as their scroll type horizontal filter. This was an outgrowth of the old Oliver Sand Table that was limited to very coarse, free filtering pulps containing no appreciable amount of fine particles. The sand table was rather limited in application. The later continuous scroll type horizontal filter provided for a reverse air blow after discharge which reslurried the heel remaining and permitted the filtration of pulps containing finer particles. In the manufacture of phosphoric acid by the ?wet? process, the filtration of gypsum from the strong acid presented an extremely difficult filtration problem due to blinding of the filter media caused by crystallization of the soluble salts contained in the acid. A filter which allowed for continuous cloth washing was required, and this led to the development of the continuous pan type, and travelling belt type horizontal filters which provided for this need. Among the filters developed were the Prayon by Engineering and Industrial Corporation of Luxembomg for use in their phosphoric acid plants. They are one of the largest manufacturers of phosphoric acid in Europe. The Dorr-Oliver Traveling Pan Filter was also developed by Mario Giorgini, Manager of Dorr-Oliver?s Italian subsidiary, for use with the Dorr Company?s phosphoric acid process. Basically, there are four existing types of horizontal filters in commercial use at this time: The scroll discharge non-pan type, the continuous belt type (Lurgi), rotary pan type, and the traveling belt type. The construction and principle of operation of these various filters will be discussed.

Jan 1, 1958

By W. R. Hardwick

This paper describes mining methods and practices of the Chino Mines Division, Kennecott Copper Corp., Grant County, N. Mex. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program was conducted from 1928 to 1939, which helped to improve the efficiency of mining operations. The primary purpose of the program is to promote development and conservation of our mineral resources by disseminating technologic information on methods, practices, and related features in mining mineral deposits. It is expected that the program will: (1) Promote efficiency in operating mines; (2) assist operators and engineers in evaluating and developing new mineral deposits; (3) provide data for engineering curriculums in mining schools; and (4) furnish performance and cost data for revising engineering handbooks and for inclusion in engineering textbooks.

Jan 1, 1958

By Calvin R. Davis

The bucket elevator is probably the oldest known form of conveyor. Its history can be traced back to the days of Babylon where wicker baskets lined with a natural pitch and fastened to ropes operating over wooden sheaves turned by slaves, were used for the elevating of water into irrigation ditches. It is not unnatural for the bucket elevator to be the first in history, for even today engineers and designers recognize that well designed, correctly applied bucket elevators offer unequaled advantages over other bulk material elevating methods. The bucket elevator's vertical design saves valuable floor space. It provides flexibility of machinery layout with lowest initial capital expenditure, which is its principal advantage. While the advantages of the bucket elevator have long been recognized, there has been a tendency to lean away from its use because of high maintenance without reliability. CHAIN Belt Company found that the bucket elevator, if correctly applied, can be built to be as dependable and reliable as any other piece of machinery in today's modern processing plants. It is not difficult to understand why the bucket elevator is looked upon sometimes as a necessary evil in the material handling system. Very little has been published or written about the specific use or application of bucket elevators other than in manufacturers catalogs. Most of today's elevator application was set forth at the turn of the century by Hetzel (1). There have been many improvements made in the manufacturing techniques of elevator components, improvements in material selections, all which can be used to improve today's bucket elevator. To best understand the improvements which have taken place recently in the design and application of bucket elevators, an understanding of basic elevator principles is desirable. In general, it can be said that bucket elevators are classified into two basic types : (1) centrifugal discharge and (2) continuous. Elevators in use today are either of the centrifugal discharge type or the continuous type, or a combination of both in special applications.

Jan 1, 1958

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By P. D. Southgate

VIBRATION, both ultrasonic and sonic, can affect the course of a variety of metallurgical processes. Reports of work on this subject have appeared at intervals over the last twenty years and a thorough review has been made by Hiedemann,' who gives a full list of references. It has been established that both refinement of structure and outgassing of the melt can be produced in most metals with sufficiently intense vibration. Many of the experiments in this field have been carried out using alloys of direct commercial interest in production- type casting equipment. Here a different approach is adopted, and simple binary alloys which exhibit different types of structure are used to facilitate examination of the effects produced under well-controlled conditions. Results from this kind of experiment should enable the basis of larger scale experiments with similar types of materials to be better substantiated. The alloys selected for this work are: 1) aluminum of 99.2 pct purity, the principal impurity being iron, near 0.4 pct; 2) A1-1.8 pct Fe, which is near eutectic composition; 3) A1-4 pct Fe—the second phase, of composition FeAl3, forms distinct acicular crystals; and 4) A1-12 pct Si—although this is of eutectic composition, the silicon normally appears in the form of large plates. Experimental Method There are three practicable methods by which acoustic vibration can be transferred to liquid metals: a) vibration of the whole of the container; b) electromagnetic induction; and c) insertion of a vibrating probe into the liquid. Method c is chosen here, and a frequency of 8 kc per sec is used. The end of the probe is electrically heated so that the metal near it will be the last to solidify. This ensures that vibration is transmitted directly to the liquid metal without passing through any solidifying and pasty intermediate region, which would attenuate acoustic waves severely. In addition, the heating prevents solid metal adhering to the probe, with consequent detuning. The transducer assembly is shown in Fig. 1. A stack of Permendur laminations 30 cm long acts as a half-wave vibrator and a winding along its length carries polarizing and energizing currents. It is joined by a half-wave coupling bar to a mild steel exponential horn, which tapers from 3.8 to 1.1 cm diam. A stainless steel stub 3 cm in length is welded on the free end. The assembly is supported by a plate located at the node of the coupling bar. Acoustic radiation losses are minimized by allowing the free end of the transducer to protrude above the surface of the cooling water. The exponential horn serves the function of matching the acoustic output impedance of the transducer to the radiation resistance of the probe into the melt. Electrical drive is provided by a 1 kw generator. Measurements of probe vibration amplitude during melt treatment are obtained from a gramophone pick-up with the needle attached to the wide end of the horn. This device is calibrated with a microscope before use. Liquid aluminum is very actively erosive and solution of materials with which the molten metal comes into contactcauses difficulties. Erosion of the probes in particular can be severe since it is greatly accelerated by the vibration. Tests of various acous-

Jan 1, 1958

By C. A. Lorenson

THE Marmoraton mine is located a mile southeast of Marmora, a village in Hastings county, Ontario, 130 miles east from Toronto and 143 miles west of Ottawa. Highway No. 14 from Belleville intersects Highway No. 7 at Marmora and the branch line of the Canadian National railway between Trenton and Bancroft passes through the property just east of the open pit. HISTORY AND GEOLOGY The Marmora orebody appears as the whorls of a thumb print on the aeromagnetic survey map released by the Ontario Department of Min.es early in 1950, the survey of the district having been made in 1948 and 1949, under the joint auspices of the Department of Mines and the Geological Survey of Canada. The 'anomaly' appeared to have interesting possibilities, so Bethlehem representatives carried out a ground survey and began drilling the property in June, 1950. A total of 40 holes, aggregating 37,000 feet, were drilled to delineate the ore-body. The Marmora orebody is a re-placement of Precambrian limesto.ne with zones or bands of magnetite interlaid with metamorpl1ic rocks and cut by later intrusives. The ore and associated Precambrian rocks are overlain by 100 to 150 feet of flat-lying Palaeozoic limestone. It is a low-grade deposit averaging 33 per cent iron and requires concentration to raise it to 65 per cent iron grade.

Jan 1, 1958

By J. A. Russell

AS THE LOCAL electric generating plants increased in size and capacity and costs of producing electricity came down, it became apparent that it was no longer good economy to operate individual boiler plants at the Company's various collieries to power steam hoists and compressors. Great economies could be made by burning the Coal at central power plants and using electric power at the collieries. During the period after the end of the war, a steady and continuing programme of replacing first the smaller steam-driven units, and later the steam-driven compressors, was undertaken, and finally the larger hoists, those at No. 12 Colliery in New Waterford and No. 20 Colliery in Glace Bay, were the last units operated by steam.

Jan 1, 1958

By T. G. Richardson, F. M. Perkins

In the recent paper of Richardson and Perkins entitled "A Laboratory Investigation of the Effect of Rate on Recovery of Oil by Water Flooding,"' the authors found very little appzrent effect on oil recovery of having free gas saturation present prior to water flooding in unconsolidated sands. We agree that the effect in this particular system was small but do not feel that the data presented should be regarded as disproving work of others which has shown an appreciable effect. The authors do not make such a claim, but neither do they advance an explanation of the difference. In our experience the following factors must be carefully considered when studying the relation between residual oil saturation after water flooding and initial free gas saturation: (1) the magnitude of the inherent residual oil saturation, i.e., the residual oil saturation with no free gas; (2) the increase in oil-water viscosity ratio with pressure lowering if the gas saturation is obtained by solution gas drive; and (3) the oil shrinkage which occurs with pressure lowering and gas evolution. The system studied by Richardson and Perkins gave residual oil saturations as low as 20 per cent without free gas present, and one should perhaps not expect much further lowering. As an illustration of the magnitude of the effect when the residual oil saturation is inherently higher we submit the accompanying figure. These data were obtained on an unconsolidated sand under elevated pressure in a system similar to the one described by Richardson and Perkins. Gas saturation was established by gas drive before water flooding. The viscosity ratio was 600:1 under the conditions of the displacement. Here the gas was extremely effective in reducing residual oil saturation. This fact was also indicated by Kyte, et al.2 Their plots of residual oil saturation vs initial gas saturation show trends of greater free gas effect with higher oil viscosities. The pressure-dependent effects were not discussed by Richardson and Perkins. They should be separated from the free gas effect if the objective of the study is a correlation of residual oil saturation vs initial free gas saturation. The increase in oil viscosity when gas is released from solution tends to increase residual oil saturation. This effect is rather small in the viscosity range of kerosene. A Buckley-Leverett calculation, assuming an increase in viscosity ratio from 1.2 to 1.8, indicates an increase in residual oil saturation of about 1 per cent of pore volume. Thus, one would expect this system, if operated at constant viscosity ratio, to show a slightly greater free gas effect. As Dyes- as shown, oil shrinkage can offset the beneficial effect of free gas on waterflood oil recovery, if the gas saturation is established by depletion. Since

Jan 1, 1958

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By W. M. Armstrong

THE GROWTH of the major iron and steel industries on this continent and in many European countries was based on the use of as-mined, high-grade, lump iron ores and on the availability of metallurgical coking coals. The modern coke-fired blast furnace was developed for such materials and is one of the most efficient of ail pyrometallurgical processes. Most of the impure pig iron produced by blast furnaces was converted to refined steel by the Bessemer process in the years prior to 1900 but, when large quantities of low-cost steel scrap be-came available, the more flexible open hearth process was adopted by most large steel producers on this continent. Although this pro-cess has many desirable metallurgical features, the thermal efficiency is low, the capital cost is very high, and the method of charging scrap steel is inefficient by modern standards of material handling. In recent years several conditions have arisen which have stimulated the development of many new pro-cesses and the re-examination of the existing smelting and steelmaking techniques.

Jan 1, 1958

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958