Search Documents

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Tobias Krull

The characterisation of iron ore from a materials handling point of view is paramount in order to provide the best possible design for the desired application and maximise equipment uptime at the lowest possible capital and operational expenditure. Problematic issues in materials handling applications often arise in the iron ore industry due to the high density of the ore as well as the abrasive nature of the product. One of the key issues encountered during the handling of iron ore is excessive wear due to either impact or sliding abrasion. The applications and equipment typically affected by accelerated wear issues are mass flow hoppers, transfer chutes and conveyor belts. These wear issues often result in unplanned down times and loss in production which can lead to a considerable loss in revenue. This paper provides an overview of the best practises in the materials handling characterisation of iron ore and discusses available techniques for the modelling of iron ore in applications where accelerated wear is experienced. The application is illustrated through a number of industry relevant case studies for which engineering design work was undertaken to successfully reduce the wear rates of different materials handling equipment.

Aug 1, 2018

By Ismael Vemdrame Flores

No panorama atual da coqueificação há uma necessidade comum de aumentar o uso de carvão de menor qualidade, principalmente devido ao alto custo e decrescente disponibilidade de carvões coqueificáveis de primeira linha. Neste cenário, uma forma de melhorar a qualidade do coque é através do controle de tamanho de partículas de carvões e misturas. A granulometria dos carvões pode alterar sua petrografia e propriedades reológicas, podendo ser utilizada de forma benéfica. O presente trabalho é uma primeira parte de um estudo de longo prazo e tem como objetivo avaliar os efeitos de preparação de carvão em suas propriedades. Para esse fim, dois carvões coqueificáveis e uma mistura foram selecionadas e caracterizadas em diferentes faixas de tamanho de partícula. Os carvões e suas frações granulométricas foram caracterizadas por análise imediata, petrografia, fluidez Gieseler e índice de inchamento livre. Os resultados demonstraram que as frações granulométricas dos carvões apresentam diferentes propriedades (cinzas, matéria volátil, composição maceral, fluidez e FSI) de acordo com o tamanho de partícula estudado. Além disso, discutiu-se o motivo por trás das diferenças observadas.

Aug 1, 2018

Os mais importantes processos de redução de minério de ferro em fornos de cuba convivem, com maior ou menor intensidade, o problema de precipitação de carbono no interior de seus reatores. Para melhor conhecer os efeitos dos parâmetros operacionais desses processos sobre as cinéticas simultâneas de redução das pelotas de minério de ferro e de precipitação de carbono, foi definido um programa cooperativo entre a Samarco e o Grupo de Siderurgia da PUC-Rio. O presente trabalho é a parte 1 deste programa, que analisou o comportamento de pelotas RD nas temperaturas de 500, 700 e 900 °C, vazões de 60 e 90 NL/min e pressões de 1,2 e 2,5 atm, quando reagiram com os gases de topo e sopro típicos das regiões superiores (Zona de Redução-ZR) dos fornos de produção de ferro esponja (DRI). O tratamento dos resultados obtidos nos testes programados pelo método estatístico fatorial, permitiu identificar as cinéticas concorrentes e propor um modelo global baseado no principio da superposição. Finalmente, utilizando as curvas “Grau de Reação Global-GR versus tempo”, mostrou correlações plenamente compatíveis com os dados experimentais levantados e plena viabilidade de aplicação a outros processos de produção de ferro primário.

Aug 1, 2018

By Ana Maria Guilherme Bailon

A coesão entre os grãos de ferro em pelotas queimadas é afetada por mecanismos difusionais dependentes de tempo e temperatura de sinterização e do tipo de elementos presentes na escória. Óxidos presentes nos insumos e no minério exercem influência significativa no processo de difusão das partículas de ferro e na formação de escória, composta principalmente por CaO, SiO2, Al2O3 e MgO. O estudo da influência da escória na microestrutura de pelotas de minério de ferro permite um maior entendimento das principais características relacionadas às fases formadas, que afetarão diretamente sua resistência física e comportamento metalúrgico. Neste trabalho abordamos a influência da variação nos teores de CaO e SiO2 na estrutura das pelotas com o objetivo de verificar a interferência desses compostos na diminuição da energia livre superficial e crescimento de grão bem como na distribuição de porosidade e formação de fases como hematita, sílicatos, ferritos e, eventualmente, a magnetita. Para tal avaliação, pelotas com diferentes teores de escória passaram por caracterização química, análises em Microscópio Óptico e análises em Microscópio Eletrônico de Varredura.

Aug 1, 2018

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By Jan Krull

A high productive coke making process in connection with stringent emission control has clearly become a demand of plant operators and stakeholders. Further to this, availability, quality and coal costs are key concerns for the iron and steel industry in its efforts to optimize raw material cost. Today, the optimization of raw material cost in integrated steel works has further gained priority. Coking coal reflects up to 20% of the cost of steel. In top charged batteries coal preparation and blending is one of the concerns to lower coal cost by maximizing the percentage of non-coking coals in the blend. Stamp charging technology is technologically and economically an effective solution in the process of pre-carbonisation. Paul Wurth’s jumbo top charged oven as well as proven stamp charging technology have recently set new benchmarks in Europe, India and Brazil in terms of productivity, stability and emission control.

Aug 1, 2018

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Fernando Nunes da Silva

Wear mechanisms of materials that constitute the equipments and operating parts in the pre-salt area during the production of petroleum and gas can include corrosion, corrosion-cavitation and corrosion-cavitation-erosion. In the laboratory, it is realizable, but at times it is inaccurate to reproduce or visualize some of these mechanisms due to the real complexities caused by hydrodynamic flows, and the physico-chemical and mechanical non-linearities. The main objective of this work was to study coupons of low carbon steel under laboratory conditions, such as corrosive, cavitative-corrosive (CO2) and corrosive-erosive (CO2 + SiO2), in a stirring aqueous saline solution (0 and 5.0 m/s) at two levels of temperature, with bubbling of gas (5.0 L/min) and contaminated with or without (2.5 % mass), by solids particles of SiO2. The surface of the coupons subjected to upstream flow (0° in a cylindrical generatrix of coupon), and downstream flows (180º) were analyzed by profilometry. The measurements of roughness and waviness of all coupons were statistically analysed using Statgraphics® Centurion XVI, at a confidence level of 95% and significant differences observed in some matrices were discussed.

Jul 31, 2018

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Evan Thomas

It has been shown before that liquids can slip at a solid boundary, which prompted the idea that parallel-surface bearings can be obtained by the use of alternating slip and non-slip regions in the direction of fluid flow. The amount of slip at the wall depends upon the surface tension at the liquid - solid interface, which in turn depends on the chemical composition of the surface and its roughness. In the present study a heterogeneous surface was created by coating half of a circular glass disc with a coating repellent to glycerol. A rotating glass disc was placed at a known distance above the coated stationary surface and the gap was filled with glycerol. With the top surface moving in the direction of slip to non-slip region, a pressure build up can be theoretically predicted. The pressure gradient in the two regions is constant, similar to that in a Rayleigh step bearing, with the maximum pressure at the boundary. In order to accurately measure the force generated by the pressure increase, a load cell was attached to the heterogeneous disc. Experiments were conducted by varying both sliding speed and distance, and the resultant load carrying capacity was measured and compared with theoretical calculations. This allowed the slip coefficient of the coated surface to be evaluated.

Jul 31, 2018

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By Salete Martins Alves

The future lubricants must be more environmentally adapted, with a higher level of performance lower total life cycle, cost than currently used lubricants. Environmental friendly, the biodegradable alternatives are available for a large variety of mineral oil based lubricants. Vegetable oils are the major source of these base fluids, although they have lower thermal and oxidation stability and even worse low-temperature behavior than mineral oil. These physical and chemical properties can be improved by chemical modification. The aim of this study was to evaluate physicochemical properties and film formation from modified vegetable oils. The vegetable oil was chemically modified by epoxidation reaction with acetic and formic acid using sunflower oils. Viscosity, iodine value, density, acidity value and thermal stability were determined for epoxidized oils. The film formation was analyzed using a HFRR tribometer. The results showed that epoxidized vegetable oils had excellent properties to be used as lubricant, and their tribological performance is higher than mineral oil.

Jul 31, 2018

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018