Search Documents

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

By W. H. Eddy

The Bureau of Mines made small-scale continuous tests and large-scale commercial plant tests of a calcareous fluorspar ore near Cave-In-Rock, Ill., to determine if the application of the lignin-fluoride process of fluorspar flotation would be industrially feasible for treatment of fluorspar ores, and also to compare the lignin-fluoride process with the quebracho process, which is the method currently used for concentrating calcareous fluorspar ores. The small-scale continuous tests yielded fluorspar concentrates analyzing 93.6 percent CaF2 with a recovery of 87.6 percent of the total fluorspar in the ore. In large-scale commercial plant tests, a fluorspar concentrate analyzing 93.3 percent CaF2 with a recovery of 78.0 percent was produced by the quebracho method. About 86.0 percent of the fluorspar was recovered in a metallurgical-grade fluorspar concentrate from the lignin-fluoride circuit which analyzed 89.9 percent CaF2? with a much simpler flowsheet than that in the current commercial application.

Jan 1, 1967

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967

By Arcy R., D&apos George

A process for removing sulfate from Great Salt Lake brines and other natural brines, including sea water, has been developed. Sulfate is quantitatively removed by precipitation as barium sulfate in a cyclic process employing ion-exchange techniques. Barium is continously recovered and recycled, and sodium carbonate and sulfur or sulfuric acid are produced as byproducts in quantities sufficient to more than defray the cost of desulfation.

Jan 1, 1967

By Russell E. Griffin

Dielectric constants and dissipation factors were measured for six rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Results for both dry and moist specimens are presented and compared with data reported by others. Loss factors calculated from the data presented are important to the Bureau's study of rock fragmentation by means of dielectric heating.

Jan 1, 1967

By J. Gurland

The wmk is concerned with the estimate of the degee of continuity of a particulate phase dispersed in a matrix. The first section is a verieu: of the parameters nzeasurable by quantitative rnetallogvaphy, namely the contact area and, under certain conditions, the number of contacts between particles of one phase. In the second section, the frequency of particle contacts is related to the degee of continuity of a randomly embedded phase orz the basis of the lattice-percolation model of Hamrnersley and others. THE extent of continuity of the constituent phases may greatly influence the structure-sensitive properties of phase mixtures, particularly if the phase properties differ significantly. An example from the literature1 is shown in Fig. 1. The marked decrease of the electrical resistivity of sintered silver-alumina bodies near 25 pct by volume of silver presumably occurs because the more conductive phase changes from a discontinuous to a continuous structure. Other example of electrical- and thermal-conductivity transitions are cited by kingery In view of these observations, a knowledge and understanding of the connectivity of the microstructure may be of considerable practical importance. This study is concerned with one aspect of the genera1 problem, namely the estimate of the degree of continuity of a particulate phase dispersed in an opaque matrix. The first section reviews the parameters measurable on a polished cross section by auantitative metallography, such as the contact area and under certain conditions, the number of contacts between particles of one phase. In the second section, an attempt is made to relate the frequency of particle contacts to the degree of continuity of a randomly embedded phase. For the purpose of this discussion, the aggregate has two constituents: the particulate phase and the matrix. The latter is considered to be homogeneous. The term "particle" is used with the meaning of "grain", i.e., a minute unit of matter which is usually a single crystal of a readily distinguishable substance within the confines of a simply connected boundary. While many of the concepts which are used here to describe the structural variables characterizing the microstructure of phase mixtures are qualitative and ill-defined, they are presented with the intent of stimulating further work of a more general and rigorous nature. I) PARTICLE CONTACT, CONTIGUITY, AND MEAN FREE PATH 1) Measurement of Contiguity. The fraction of the total internal surface of a phase a shared with particles of that same phase in a two-phase mixture of and $ is indicated by the contiguity ratio:3 whereis the area of the interface between o particles, and Sap is the area of the interface between a particles and matrix P, per unit volume of mixture. The contiguity ratio ranges from 0 to 1 as the distribution of the a phase changes from a completely dispersed to a completely agglomerated structure. The interfacial areas may be obtained from simple intercept measurements on a random plane, after Smith and Guttman where and N are the numbers of intercepts between a random line of unit length on a plane of polish and the interparticle and interphase interfaces, respectively. The equations are valid for any distribution of particle sizes and shapes.

Jan 1, 1967

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By K. Mukherjee

A quasi-thermodynamic calculation is presented for estirt~ating vacancy Parameters in fcc metals. For fcc metals the equilibrium vacancy concentration at the melting point can be approximated by a constant mole fraction. The Gibbs free energy of formation of the vacancies can then be expressed as a simple function of the absolute melting temperature alone. From this description the formation energy Ef, the vibrational entropy Sv, and the formation volume of a vacancy can be calculated in terms of known thermodynamic parameters. The calculated values are in good agree-rnent with available experimental results. IT appears that many of the physical parameters associated with lattice defects can be empirically related to thermodynamic melting parameters.'-7 Besides the implicit correlations between melting phenomenon and point defects, the melting temperature itself at atmospheric pressure can be used as a reference temperature for the purpose of comparison of vacancy concentrations in a given crystal class. The concentration at the melting point then corresponds to the maximum vacancy super saturation in the crystalline state at a fixed pressure. For pure fcc metals such as Au, Cu, Al, Ag, Pb, and Pt the mole fraction of vacancies at the melting point8 is of the order of 10*"3 to 10"1. The equation expressing the equilibrium vacancy concentration at the melting point contains three parameters: the formation energy, the vibrational entropy, and the absolute melting temperature, see Eq. [2]. Since these three parameters cover a wide range of values8 in the above-mentioned metals, it can be assumed that in other fcc metals, for which no reliable data are available, the mole fraction of vacancies at the melting point most likely lies in the range 10~3 to lO"4. This is then the basis of the calculations described in this article. Within this range the mixing entropy can be linearized and the vibrational entropy, the formation energy, and the vacancy formation volume can be calculated in terms of known thermodynamic constants. 1} LINEARIZATION OF MIXING ENTROPY The Helmholtz free energy of a crystal containing n vacancies at the melting point can be writteng as where Ef, T,, k, and S, are the formation energy of a vacancy, the absolute melting temperature, Boltz-mann's constant, and the vacancy formation entropy, respectively. After applying Stirling's approximation in Eq. [l] and minimizing with respect to n where (n/N), is the equilibrium vacancy concentration in mole fraction at the melting temperature at 1 atm pressure. If instead of setting (6~/6n) = 0 immediately after Stirling's approximation in Eq. [I], the configurational partition function is simplified, then some useful and significant results can be obtained by utilizing the experimental inforrnation After applying Stirling's approximation and rearranging is plotted as a function of (n/N) in Fig. 1. The points, not all of which are shown, are fitted by a straight line substituting from Eq. [5] into Eq. [I] and minimizing with respect to n combining Eqs. [6] and [2] It must be emphasized that Eq. [7] is only a crude approximation based on an oversimplified model of

Jan 1, 1967

By O. C. Baptist

The gravitational pressure gradient (GPG) in porous sandstone containing free gas was determined to define the proper GPG to use when calculating the rate of downdip flow of oil in the Sub-Scalez No, 1 sand, Elk Hills field, Naval Petroleum Reserve 1. The GPG was determined at several gas saturations using long, artificially consolidated sandstone models that were mounted vertically in some tests and horizontally, with rotation, in others. Also determined by laboratory and field tests were relative permeabilities, capillary pressure relations; critical gas saturation, water sensitivity, and depletion drive performance. The critical gas saturation in the models having an absolute permeability of 1 to 2 darcys was about 2 percent of pore volume. The GPG with the critcal gas saturation was that due to the weight of the gas-saturated oil. The GPG in the upper part of the models was reduced as gas saturation increased to a value considerably larger than the critical. The exact gas saturation at which the GPG became less than that due to the weight of the oil could not be determined but was estimated to be of the order of 10 percent of pore volume. Tests indicate that the rate of oil production is not permanently reduced by exposure of the sand to fresh water but that the rate of injection of fresh water will be considerably less than that to brine, Methods for determining the factors mentioned above are discussed.

Jan 1, 1967

By Stanley A. Feitler

This Bureau of Mines report deals principally with the resources and economic aspects of feldspar in the United States east of the Mississippi River. Although in a strict sense, all phases of the feldspar industry affect its economic structure, emphasis in this study is on supply, demand, and marketing. Although feldspar was originally mined for use in the manufacture of pottery and other ceramics, the glass industry, which began to use feldspar in the mid-1920's, now consumes more than half of the annual output. Most mining is open cut, and the methods used are similar to those used in mining crushed b stone. Excess plant capacity has been chronic, and production is usually about 30 percent of capacity fur the industry as a whole. Since 1947, feldspar consumption has grown more slowly than the average for all U.S. industry. This has fostered intense competition, especially for the glass market. Prices have not kept pace with inflation, and profits are small. The trend of consumption through 1970 for glass feldspar is expected to be upward; less rapid in consumption of ceramic feldspar is anticipated.

Jan 1, 1967

By W. A. Backofen, D. Lee

The deformation of textured sheet of titanium and several of its all-a (hcp) alloys was investigated with two kinds of experiments: tension testing along different directions in the plane of the sheet, and combined-stress loading along the principal axes of anisotropy (the rolling and transverse directions). Texture and plastic anisotropy were evaluated with pole figures and by measurement, as a function of orientation, of the tensile transverse-strain ratio, or R parameter. The results as a whole can be rationalized qualitatively with the present understanding of deformation mechanisms in titanium. Quantitative agreement between the orientation dependence of tensile yield strength and the Predictions of continuum ANISOTROPY in the properties of engineering materials is more the rule than the exception because anisotropy in structure is so common, and the one generally follows the other. Two broad categories of structural anisotropy are represented by mechanical fibering and crystallographic texture. The former is important in many aspects of fracture.' The latter has more significance for yielding and plastic deformation, theory, using the R measurements, was relatively poor. However, in tension-tension quadrants of the yield-locus diagrams, the difference between theory and experiment was hardly more than 10 pct. The maximum texture-hardening effect was found in a 4Al-1/4O2 alloy to be nearly 50 pct. In the compression-compression quadrant, {1012} deformation twinning prevented the locus from expanding much beyond the Position predicted for isotropic material. With increasing temperature the trend in R was downwards, approaching unity (isotropy) near the a-transus temperature; an accompanying development was large amounts of neck-free extension. which are of special concern in this paper. The tendency has been to view crystallographic texture more as a liability or curio than as an asset. The prominent exception is found in silicon-ferrite sheet for power-transformer cores, which is processed to develop a new optimum texture for high electrical efficiency. Yet it should be possible to find other examples, involving other kinds of properties. More specifically, there is good analytical reason to expect improved combined-stress yielding resistance in suitably textured material,2,3 and it has now been shown by experiment that texture hardening or softening is a potentially useful phenomenon in certain engineering devices and processes.'-I To date, work has included measurements of the transverse (width to thickness) strain ratios in the

Jan 1, 1967

In his account of the Thackaringa sulphide ore, Lawrence (p. 92) reports the presence of valleriite as a minor accessory in chalcopyrite. He says that it is readily identified by its intensive anisotrophy and reflection pleochroism. He also gives (p. 87) the chemical formula as Cu8Fe4S7 Recent work by Evans et al. (1964), Chamberlain and Delabio (1965), and Schidlowski and Otteman (1966) suggests that most material identified as valleriite is, in fact, mackinawite. Mackinawite and valleriite are both extremely anisotropic and strongly reflection pleochroic, and so with fine-grained material it would be hard to distinguish them optically.Mackinawite, according to Evans et al. (p. D66) is a copper-free iron sulphide (PeS) with small quantities of nickel, whereas valleriite is considered to be a dimorph of chalcopyrite (CuPeS2 ). They found that mackinawite is much more widespread than valleriite, and, unlike the latter mineral, is commonly included in other sulphides, particularly chalcopyrite.Lawrence (p. 92) states that the valleriite inclusions are up to 0·01 mm long, so that an electron probe microanalysis should be quite feasible and provide a ready answer to this query.L. J. Lawrence: I thank Dr Townend for his comments on the occurrence of a valleriite-like mineral embedded in chalcopyrite from Thackaringa. The problem of distinguishing valleriite from mackina...

Jan 1, 1967

By R. C. Hickman

Preliminary evidence indicated that the Chattanooga Shale might constitute a potential vast low-grade source of uranium. Investigation by core drilling indicated that while the Chattanooga Shale may constitute a resource for the future, the very low (0.006 percent) average uranium content is not economic when compared with the relatively higher grade western ores. A total of approximately 12,000 feet of test drilling was done in 72 drillholes, and large samples were mined for extractive and metallurgical testing. An experimental mine site was selected on the basis of the drilling project.

Jan 1, 1967

By J. G. Walters

This report presents the results of an investigation in Which the chloroform solubilities of coals and chars are related to rank, temperature of thermal treatment, time at a given temperature, vacuum thermal treatment, plasticity, oxidation, blending, and mass spectral analyses and molecular weights of the extracts. It was found that the quantity of chloroform extract obtained from chars can be altered by creating a vacuum above the charge during preparation of the char, increasing the time at temperatures within the plastic temperature range, and by utilizing different rates of heating to attain a given temperature. Relationships found between the chloroform solubilities of chars produced at temperatures within the plastic temperature range and the relative fluidities in this temperature range indicate that the chloroform-soluble portion of the char is a significant component of the plastic mass. Chloroform-extract yields from chars made from blends of coals cannot be calculated from chloroform-extract yields obtained from chars made from the component coals.

Jan 1, 1967

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By Wilson Blake

The Bureau of Mines used a mathematical model based on the finite element method of stress analysis to calculate stresses and displacements surrounding an open pit mine in a gravity-loaded rock mass. Comparison of the finite element solution for a semicircular notch in a gravity-loaded plate with the theoretical solution for a semicircular notch in a plate under uniform compression parallel to the free boundary demonstrates the inapplicability of the latter method to openings at the free surface of a gravity-loaded medium. High stress concentrations are formed at irregularities along the boundary of an open pit in a gravity-loaded continuous competent rock; however, for this type of rock the magnitudes of the stresses are too low to be considered a major factor in open pit slope stability. High stress magnitudes will occur if, in addition to the gravity stress field, a large horizontal stress field exists.

Jan 1, 1967