Search Documents

By Robert O. Vernon

Urban sprawl, and all its attendant problems, is upon us. In Florida, and much of the rest of the world, this has been intensified by a special problem - the coastal zone - a land of high-intensity urbanization localized where the sea and our citizens interact. Florida is blessed by a long coastline of beautiful beaches, indented by estuaries, lagoons and spring fed rivers. Rocky and sand covered islands invite habitation. A large and varied fauna and flora make recreation an avocation and work a pleasure. Accompanying these people are all the sustaining, and satellite industries that find the climate, labor, and commodity markets, cheap water transportation, and natural resources to be attractive. It is estimated that by the year 2008 a megalopolis will stretch down the Atlantic Seaboard from Georgia to encompass the Keys and extend along the Gulf to Alabama. This city will be fenced by the sea on one side and by the water management works, necessary to provide the water supply for this complex, on the other. What can we do about increasing the amount of water available for this population and decreasing the resultant wastes??? Rarely has there been tendered a more favorable opportunity for a coordinated planning and development project that will provide public access to beaches and multiple use of the coastal lands. Florida, as a peninsula swept by ocean breezes, having a largely indigenous water supply and only the beginning of the pollution of estuarine and coastal waters can cope with air, water and coastal dissipation and pollution, if we have a beginning at providing a constant water supply and at limiting pollution. This answer would appear to lie underground, where the porous limestones are interbedded with impervious fine-grained sediments and ground-water that circulates through these aquifers empty to the ocean and Gulf along the continental slopes.

Jan 1, 1969

By J. Brett, L. Seigle, L. Castleman, T. Montelbano

Impurity-induced low-temperature recrystallization of cold-worked tungsten was inuestigated with emphasis on the influence of nickel on the reaction. Palladium, nickel, aluminum, manganese, platinum, and iron greatly lower the recrystallization temperature of doped tungsten, which zs normally very high, but the recrystallization temperature of electron-be am zone-refined tungsten wzre is slightly raised by conlacl with nickel. Recrystallization can be induced at low temperature by the presence of solid nickel on the surface of doped tungsten wire, but apparently not by exposure to nickel vapors alone. Approximately 200 ppm of Ni dijjused into 10-mil wires at 1200 from a deposit of nickel on the surface produced total recrystallization, whereas more than 600 ppm of Ni could be absorbed frotn a vapor source without altering the fibrous structure of cold-worked tungsten. Once initiated, nickel-induced recrystallization required a continued source of' nickel for propagation of the recrystallization front. The solubility of nickel in fibrous 10-mil W wire was approximalely 500 ppm at 1150' C, and the activation energy for penetration of the recrystallization front was 52 kcal per mole. In many applications the usefulness of tungsten depends on critical control of its structure. Cold-worked tungsten with the fibrous structure developed by suitable thermo-mechanical treatment has a low, but technologically significant, ductility. It has long been known1 that traces of nickel, and perhaps other metals, are profoundly deleterious in doped tungsten, because they induce recrystallization at low temperature, which produces a brittle, equiaxed grain structure. This effect appears to be an exception to the general observation that recrystallization is impeded and the recrystallization temperature raised by the presence of impurities.2"9 Previous studies7-'' of the annealing and recrystallization of tungsten wire have divided the phenomenon into prior recovery stages, primary recrystallization and secondary recrystallization. The present investigation is concerned principally with primary recrystallization which is defined here as the replacement of the fibrous structure of deformed tungsten by equiaxed grains. The objective of this study was to explore the nickel-induced recrystallization reaction in tungsten and attempt to elucidate its mechanism. As well, an effort to define which other elements give rise to low-temperature-induced recrystallization was carried out. EXPERIMENTAL PROCEDURE The procedure adopted for these experiments was essentially to bring nickel and other elements into diffusive contact with cold-worked tungsten wires. The process of recrystallization was followed as a function of time and temperature by light and electron microscopic observations. First the influence of nickel on the recrystallization temperature of arc-melted, zone-refined, and variously doped tungsten wire was determined by electroplating a deposit of nickel on the surface of the wire and annealing at a variety of temperatures for 3 hr. The chemical analyses of the tungsten wires used in this investigation are given in Table I. The surface of the tungsten wire was etched with Murakami's slution' and approximately 0.005 in, of Ni was deposited from a Watts-type low pH bath14 for the conditions of these experiments. Variations in plating thickness from about 0.001 to 0.005 in. had no discernible influence on the resulting structures. The wires were then annealed in an atmosphere of dry hydrogen to establish the recrystallization temperature. Concurrently, un-plated specimens were annealed to establish the recrystallization characteristics of nickel-free wire. The criterion of recrystallization was that the fibrous structure be completely replaced by equiaxed grains after a 3-hr treatment of temperature. This provided more reproducible results than use of the first recrystallized grain or a fixed proportion of re-crystallized structure as the critical observation. The structures encountered in longitudinal and transverse sections were examined by both light and electron microscopy at magnifications up to X32,000 using parlo-dion-carbon replicas shadowed with platinum for the latter method. Second, the influence of a variety of metals on the recrystallization temperature of 0.010 in. D alumina-silica doped tungsten wire, AW136-64, was determined. The elements were applied by electroplating whenever possible. Alternatively, they were vapor-plated on the tungsten wire and a greater thickness built up by coating with a dispersion of metal powder in nitrocellulose lacquer. Elements not amenable to either of these procedures were merely slurry coated on the tungsten. The recrystallization temperature was determined as above. Third, the nickel-induced recrystallization process in doped wire was studied more closely by electroplating 8 mils of Ni on 65-mil alumina-silica doped tungsten wire, AW153-NS10, and exposing the wire to temperatures of llOO°, 1200°, or 1300°C for various times in a hydrogen atmosphere. A circular recrystallization front, 'Onsisting of equiaxed grains, developed at the periphery Of the coated tungsten wire, and the advance of this front into the fibrous interior was studied. These experiments employed relatively coarse 0.065 in. D wire because the 0.010 in. D wire recrystallized too quickly to permit observation of the pene-

Jan 1, 1969

By William J. Bronkala

One of the oldest tools used in mineral concentrating is the magnetic separator. Virtually every mineral handling system has need for some type of magnetic equipment in two types of basic usage. 1. Equipment protection through tramp iron removal. 2. Mineral concentration based on magnetic properties of the minerals contained in the ore.

Jan 1, 1969

By d&apos, C. Antonio, S. H. Reichman

In the course of our studies of the annealing behavior of vapor-deposited silver films we have determined the electrical resistivity as a function of annealing temperature for films in the thickness range of 630 to 3240A. Fig. 1 shows the resistivity of the silver films vs film thickness in as-deposited and annealed conditions. The films were prepared by depositing 99.999 pct pure silver from molybdenum boats onto Vycor substrates. Deposition was conducted at a residual pressure of 5 x 10"6 Torr at rates of 20 to 408, sec-'. Thicknesses were determined using a multiple-beam interferometer. During annealing, resistance was measured using the four-probe method. Measurements were made every 5°C during two consecutive anneals to 300°C under a continuous vacuum of 2 x X6 Torr. The heating and cooling rates during annealing were approximately l° and 2°C min-', respectively. Typical resistivity vs temperature curves are shown in Figs. 2 through 4. There is an inflection point evident at 120°C on Fig. 2, the first anneal of a 3240A film. This inflection point was found on all films above approximately 1!00A on both first and second anneals. Below 1400A the inflection occurred at approximately 180°C. Figs; 3 and 4 show the first and second anneals of a 1370A film. The inflection point occurs at 180°C on the first anneal and approximately 120°C on the second. Our interpretation of this phenomenon is based on oxygen liberation from the film surface. It is well-documented that the presence of oxygen on silver surfaces causes a reversible increase in resistivity.1"3 The liberation of this oxygen, for example during vacuum annealing, would therefore cause a decrease in resistivity as observed on Figs. 2, 3, and 4 as a change in slope. This is accounted for by the decomposition of Ag20 on the film surface. The free energy of AgzO becomes positive between 125" and 225°C.4 The thickness dependence of the inflection points can be explained as an orientation effect. The films used in this study were preferentially oriented with their (111) planes parallel to the Substrate.''~ In addition it has been sten that the thinner films, below approximately 1500A, possess a decided "hill and valley"

Jan 1, 1969

This method determines tellurium at concentrations down to 0·01 p.p.m., with geochemical accuracy. Tellurium is volatilized from the rock at 800°C in the presence of sulphur from decomposing pyrite, condensed, dissolved, and finally determined by atomic absorption in a long tube burner. The distribution of Te is shown near some gold lodes at Kalgoorlie. Lastly, a method of synthesizing Te-free pyrite from sulphur and ferrous sulphate is described.

Jan 1, 1969

By W. M. Robertson

The formation of grain boundary grooves on surfaces of poly crystalline samples of cobalt and iron immersed in liquid lead has been studied. The grooves form by volume diffusion of the solutes cobalt and iron in the liquid. The diffusion coefficients of the solutes in liquid lead are derived from the measured rate of grooving. The diffusion coefficients are described by the relation D = Do exp (-Q/RT), with, for cobalt, Do = 4.6 x 10-4 sq cm per sec and Q = 5300 ± 800 cal per mole, and for iron, DO = 4.9 x 10-3 sq cm per sec and Q = 10,500 ± 1500 cal per mole. LIQUID metal-solid metal interactions occur at solid-liquid interfaces. Interfacial energy provides a driving force to change the morphology of the interface. Mullins1,2 has derived expressions for the kinetics of interface morphology changes driven by capillarity. These expressions can be applied to an isothermal system of a solid in equilibrium with a liquid saturated with the solid. Surface profile changes can occur by volume diffusion of the solute in the liquid, by volume self-diffusion in the solid, and by interfacial diffusion at the liquid-solid interface. A groove will form at the intersection of a grain boundary with a solid-liquid interface, reducing the total interfacial free energy of the system. The solid-liquid interfacial energy ? must be greater than half the grain boundary energy of the solid ?6 for Mullins' calculations to apply. If ? is less than ?b/2, then the liquid penetrates the boundaries, separating the grains rather than forming grooves. Boundary penetration did not occur in the work described here. where CO is the equilibrium volume concentration of the solid in the liquid, Dv the volume diffusion coefficient of the solid in the liquid, ? the interfacial free energy of the solid-liquid interface, O the atomic volume of the solid crystal, k Boltzmann's constant and T the absolute temperature. Eqs. [1] and [2 ] also apply to grooving by volume self-diffusion in the solid,1 with CoODv = D Self, where DSelf is the volume self-diffusion coefficient of the solid. For a grooving mechanism of interfacial diffusion at the solid-liquid interface, the groove width is given by2 where CS is the interfacial concentration of the diffusing species, and DS is the interfacial diffusion coefficient. Eqs. [1] and [3] can be used to determine the mechanism of groove growth. A t1/3 dependence of the growth indicates volume diffusion and t1/4 indicates interfacial diffusion. In some cases, volume diffusion and interfacial diffusion both can contribute substantially to the grooving process, causing the time dependence to be intermediate between t 1/3 and t1/4.3 For these cases, the relative contributions of the two processes can be separated.4 However, in many cases, one process will be dominant, and the data can be analyzed on the basis of Eq. [1] or Eq. [3] alone. The time dependences for volume diffusion in a liquid and volume self-diffusion in a solid are the same. However, the self-diffusion contribution of the solid is usually negligible compared to volume diffusion in the liquid. After the grooving mechanism has been determined, Eq. [1] or Eq. [3 ] yields the kinetic parameter A or B. The kinetic parameter can be used to calculate values for the unknown quantities in the product CD?. Usually C is known or can be estimated. If ? is known, then D can be calculated. In a measurement of grain boundary grooving of copper in liquid lead,' the time dependence indicated volume diffusion in the liquid. The quantities Co, Dv, and ? were obtained from the literature, giving excellent agreement between the observed values of A and the values calculated from Eq. [2 ].5 In a study of the grooving of several refractory metals in liquid tin and liquid silver, A1len6 educed that grooves formed by volume diffusion in the liquid. In a study of nickel in a nickel sulfide melt, Steidel, Li, and spencer7 found volume diffusion grooving kinetics. Both Dv and ? were unknown, so they could not obtain either one separately, though they did obtain a reasonable value for the temperature dependence of the product Dv ?. Several methods have been used to obtain surface profiles. It can be done by sectioning through the interface7 or by chemically removing the liquid from the solid surface after solidification of the liquid.6 However, if the liquid dewets the solid on removing the solid from the melt, then the interface can be observed directly. This method was used previously' and was utilized also in the present study. EXPERIMENTAL PROCEDURE Lead of 99.999 pct purity was obtained from American Smelting and Refining Co. Cobalt sheet was obtained from Sherritt-Gordon Mines, Ltd., with a nominal purity of 99.9 pct, the principal impurities being nickel, iron, copper, carbon, and sulfur. The sheet was

Jan 1, 1969

By Mary A. Barrett

The Bureau of Mines conducted a laboratory-scale investigation of grouting mixtures containing iron or aluminum to determine the existence of health or explosion hazards, due respectively to oxygen depletion or hydrogen emission. Mixtures containing iron created an oxygen deficiency in less than 24 hours and released small amounts of hydrogen; a health hazard could occur but only under extremely unfavorable conditions. Mixtures containing aluminum released little hydrogen and consumed little oxygen; however, if improper on-site mixing yielded high local metallic aluminum concentrations, enough hydrogen might be released to produce an explosive atmosphere in a confined space.

Jan 1, 1969

By B. V. P. Rao, H. L. Lovell, G. Simkovich

In the study described here, flotation tests were conducted on pure CaF2, on CaF2 doped at several concentration levels with either NaF or YF3, and on natural fluorite samples containing various amounts of impurities in an effort to extend previous knowledge of the influence of crystalline point imperfections on the flotation properties of solids. The results of these tests showed that although recoveries generally decreased as impurities increased, the differences in recovery were not nearly as striking as those detected in earlier experiments. A number of experimentalists have shown an interest in the way in which crystalline point imperfections affect the flotation properties of solids. As long ago as 1953, Welch hypothesized that it might be possible to control surface imperfections and thereby also control the flotation of solids.' A few years later, in some rather extensive work, Plaksin and his coworkers varied the surface imperfections of a number of compounds by oxidation or reduction processes and found that significant variations in flotation properties resulted.2-4 More recently, Simkovich showed that the recovery of both AgCl and PbS could be markedly varied by adding solid-solution impurities, which acted as doping agents, to these compounds.5 Then Mular studied the flotation of ZnO as a function of the doping agents Al2O3 and Li2O.6 Once again, it was found that these impurities, even in very low concentrations, had profound effects upon flotation recoveries. From an imperfection point of view, the defect structures of the compounds tested previously are as follows:7 PbS — amphoteric semiconductor with a Frenkel-type defect structure in the cation sub-lattice.8 AgCl - ionic conductor-Frenkel type defect structure? ZnO — n-type semiconductor, zinc ion interstitials and quasi-free electrons.10 All of these works undoubtedly bear some relation to the findings that the flotation properties of seemingly identical minerals from different ore deposits often exhibit extreme variation in flotation behavior, i.e., that small amounts of analytically undetectable impurities often have a great influence upon flotation

Jan 1, 1969

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.' This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969

By F. T. M. White, W. A. Bardswick

"The parameters of airborne minerallic particulates which create industrial dustiness, together with the physiological hazards caused by their inhalation, are reviewed. Various techniques of dust sampling are discussed and analysed, and the parameters referred to above are classified as the basis for methods of assessing the physical, chemical and mineralogical characteristics of dust-particle suspensions. The paper surveys those methods of assessment currently accepted by various statutory authorities, and reviews other methods that warrant attention and newer techniques that are being developed."

Jan 1, 1969

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies'-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday's law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5'= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By Sidney Katell

This report, covering the period January 1968 through December 1968, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the tenth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost of engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Lines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress s 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing. 9. Cost Engineering. 10. European Chemical News. 3 11. Hydrocarbon Processing. 12. Industrial and Engineering Chemistry 13. Oil and Gas Journal. 14. Petroleum Engineer. 15. World Oil.

Jan 1, 1969

This study was done to evaluate the economic and technical considerations of using pozzolanic materials in order to guide cement manufacturers, pozzolan producers, contractors, Government organizations, and others interested in concrete construction work. Five hundred and thirty-eight samples of pozzolanic raw materials were taken from 27 central and western States. These samples were evaluated by petrographic procedures, and about 200 of the most promising ones were given a complete series of physical tests (American Society for Testing and Materials) to evaluate further their suitability as a pozzolan. This investigation showed that deposits of natural pozzolan materials were widely dispersed in the central and western parts of the United States but that exploiting these deposits would depend on whether they could compete economically with an increasingly abundant industrial waste product--fly ash.

Jan 1, 1969

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th'rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling' in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By H. L. Retcofsky

Carbon-13 nuclear magnetic resonance (18CNMR) spectra of nine 2-substituted pyridines, seven 3 -substituted pyridines, and nine 4-substituted pyridines have been obtained and analyzed. Substituents included both electron-releasing groups and electron-with hawing groups. Substituent effects on the magnetic shieldings of the ring carbons, except for those in the 2-positions of 2-substituted pyridines, were found to be quite similar to the effects reported for the monosubstituted benzenes, Thus, at least to a first approximation, the two classes of compounds have similar shielding mechanisms. Shieldings of the carbon atoms in the 5-positions of 2-substituted pyridines and those in the 6-positions of 3-substituted pyridines were found to reflect electron release or withdrawal by substituent groups, The pyridinium cation and the compounds 2,2'-dipyridyl and benzonitrile were also investigated.

Jan 1, 1969

Applications of helium in aerostatics, cryogenics, space, and undersea work are described in papers from the Helium Applications Symposium. Specific subjects include investigations of X-ray sources by means of balloon-borne instruments, meteorological soundings by balloons, powered lighter-than-air flight, tethered balloons, refrigeration techniques, large superconductive magnets, electronic devices, superconducting transmission lines, high-precision thermal conductivity analysis, He3-He4 dilution refrigerators, uses of helium in the atomic energy program, helium-cooled nuclear reactors, power- plant applications for high-temperature gas-cooled reactors, helium welding of stainless steel tubing and pipe, development of helium-shielded arc welding, helium as a diluent in spacecraft atmospheres, helium utilization in the Saturn-Apollo program, and helium utilization in diving environments. Papers from the Helium Centennial Symposium at the national meeting of the American Chemical Society cover the history of the discovery of helium, the history of its development by the Bureau of Mines from a laboratory curiosity to an important item of commerce, the source of helium in natural gases, the world of liquid helium, and liquid helium-3.

Jan 1, 1969

By Haskiel R. Shell

While the original purpose of the Bureau of Mines work on fluorine micas was to synthesize large single crystals or film suitable to replace natural muscovite or phlogopite, the objective was broadened to include development of the many possible fluorine micas as a class of new, unique materials. Several methods were developed for the synthesis of the fluorine micas at atmospheric pressure: Solid state reaction, melting in crucibles, internal resistance electric melting, and arc resistance electric melting. The latter two methods are now med commercially. A variety of fluoromicas were synthesized by isomorphic substitution including disilicic, trisilicic, and tetrasilicic. Fluorophlogopite, KMg3AlSi3O10F2, is the fluoromica most widely used. While most of the fluoromicas are completely stable to water, many water-swelling fluoromicas and fluoromontmorrilonoids were synthesized. Single crystals or film of the fluorine micas were grown to 2 inches or more by a number of methods, but none has as yet proved economical. In the report, detailed data and descriptions are given on compositions, syntheses, products, and uses, and on the properties including physical, dielectric, chemical, X-ray, optical, and structural.

Jan 1, 1969