Search Documents

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By L. W. Holm

This study shows that in the presence of foam, gas and liquid flow separately through porous media representative of reservoir rock. These results were obtained by using tracer techniques to measure the flow of the gas and liquid comprising the foam. Foam does not flow through the porous medium as a body even when the liquid and gas are combined outside the system and injected as foam. Instead, the liquid and gas forming the foam separate as the foam films break and then re-form in the porous system. Liquid moves through the porous medium via the film network of the bubbles and gas moves progressively through the system by breaking and re-forming bubbles throughout the length of the flow path. The flow rates of the gas and liquid are a function of the number and strength of the films in the porous medium. There is no free flow of gas; i.e., no continuous gas phase. On the basis of these results, foam can be expected to improve a water flood or gas drive by decreasing the permeability of the reseruoir rock to a displacing liquid or gas. This improves the mobility ratio and thus the conformance of the flood. INTRODUCTION Foam is formed when gas and a solution of a surface active agent are injected into a porous medium either simultaneously or intermittently. During the past few years, several papers have been published on the subject of foam flow in Dorous media. Foam has been used successfully in the removal of capillary water blocks from producing formations.&apos;&apos;2 The use of foam in gas storage reservoirs to reduce gas leaks and to increase storage capacity has been considered in recent years. Foam has also been investigated as an oil displacing agent,3-5 and as an agent to improve the mobility ratio in a waterflood.6-10 However, the mechanism by which the gas and liquid phases comprising the foam flow through a porous medium has nor been described adequately. Normally, when two immiscible phases (gas and liquid) flow concurrently through a porous medium, each phase follows separate paths or channels. At given saturations of the two phases, a certain number of channels are available to each phase, and as saturations change, the number and configuration of the channels available for each phase also change. The effective permeability of each phase is a function of the saturation of that phase only, and the flow of each phase can be described by Darcy&apos;s law. When foam is present, the effective permeability of the porous medium to each phase is greatly reduced compaced with permeabilities measured in the absence of foam.6,11-13 Based upon the observed flow of surfactant solutions and gas in capillaries, it has been concluded that the gas and liquid may flow separately or they may flow combined as foam. At least four mechanisms have been postulated to explain how fluids flow with foam present: 1. A large portion of the gas is trapped in the porous medium and a small fraction flows as free gas, following Darcy&apos;s law.9 2. The foam structure moves as a body; the rate of gas flow is the same as the rate of liquid flow. 6,13 3. Gas flows as a discontinuous phase by breaking and re-forming films. Liquid flows as a free phase.12 4. A portion of the liquid and gas move as a foam body while excess surfactant solution moves as a free phase.14 It also has been suggested that different flow mechanisms exist for high quality (dry) foams made from dilute surfactant solutions and for foams made from more concentrated solutions. Studies conducted on the flow of foam through capillaries have shown that a plug-type flow occurs and that foam flows as a body.6,15 Fried also has described the flow of foam through porous media as

Jan 1, 1969

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.&apos; However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By S. J. Aparo

Phosphate mining and beneficiation in the State of Florida are presently being carried on by 12 different mining companies with a total of 21 mining and flotation plant locations. Their combined production of both washer rock and flotation concentrate was approximately 28,000,000 long tons in 1968. This accounted for 70-72% of the total U. S. production and close to 30% of the world&apos;s output of this mineral. From this extensive activity in the Florida phosphate field, one basic flow sheet for beneficiation of the ore has developed over the years as the most commonly employed. In fact, all of these plants with the exception of two beneficiate Florida pebble phosphate using a basic operation as illustrated in Figure I. The two plants which differ from this general approach are not using raw matrix as feed. In one instance, +14 mesh pebble is ground in a rod mill to release free silica which is subsequently removed in a cationic froth flotation circuit using an amine acetate blend and kerosene. This technique generally results in a 4-7 BPL unit upgrading of the feed pebble. The other exception to the standard flow sheet illustrated in Figure I is an operation which is beneficiating tailing piles. In this case, the material is first subjected to cationic froth flotation in order to upgrade the feed to a point comparable to normal matrix. Thereafter, after, the phosphate is floated in an anionic rougher circuit followed by cationic flotation of the silica in a cleaner circuit.

Jan 1, 1969

By G. R. Webber, L. M. Azzaria

"The wide interest in the application of the geochemistry of mercury to mineral exploration is leading to the continued development of a variety of analytical methods for the determination of nanogram quantities of this element. The various methods have different degrees of reliability, sophistication and portability. In this investigation, two simple portable instruments were used in geochemical prospecting surveys -an ultra-violet absorption instrument and a similar one modified with gold for the removal of interfering substances. The results show the application of the method to the determination of mercury in soils of different organic content, and in rocks, sulphides and air."

Jan 1, 1969

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

By David V. Ragone, James A. Craig, Richard E. Balzhiser

The Gibbs free energies of formation of UC2 and UC were measured by equilibrating two-phase mixtures of UC2 + C and UC, + UC with liquid bismuth. The measured equilibrium concentrations of uranium in the bismuth combined with available activity coefficient information yielded uranium activities in these two-phase regions. Measurements on UC2 were performed over the range 1015 to 1160 K and on UC over the range 1115° to 1165°K. The values obtained for UC2 are in excellent agveement with values determined using combustton calorimetry and low-temperature heat capacity measurements. The UC values are in fair agreement with the calorimetric values, differing by about 10 pct from the calorimetric determination. MUCH interest has been shown in the uranium carbides in recent years because of their potential as nuclear fuels. As nuclear reactor operating temperatures have been raised to increase thermal efficiency, new fuels have been required. The uranium carbides are of interest because of their high melting points, >2000°C, high thermal conductivity, and resistance to irradiation damage. The manufacture and use of uranium carbides are aided by a knowledge of their stability and reactivity under various conditions. In this regard the thermo-chemical properties of the carbides, i.e., heat capacity, heat of formation, free energy of formation, and so forth, are particularly important. A great amount of work has recently been done on the thermodynamics of the U-C system. Unfortunately, however, there has not been good agreement among the various investigations. This study of the free energies of formation of uranium monocarbide and uranium di-carbide in the temperature region 1100°-1200° K was undertaken to help clarify the situation. It should be noted that in the temperature range of this investigation, 1100°- 1200° K, the thermodynam-ically stable phase in equilibrium with graphite is U2C3, not UC2, Fig. 1. However, U2C3 is reported to be stable only under extremely low oxygen and nitrogen pressure. Although UC2 is metastable below 150O°C, it exists under most experimental conditions. It should also be noted that "UC," never exists as UC2 but with compositions near UC1.9. However, "UC2" will be used to designate the dicarbide phase except when the stoi-chiometry is necessary for clarity. METHOD The approach taken in this study of the free energies of formation of UC and UC2 was to determine the thermo- dynamic activities of uranium in the two-phase regions UC, + C and UC + UC, by equilibrating the two-phase mixtures with the liquid bismuth. When a mixture of solid UC2 + C is brought to equilibrium with liquid bismuth, the reaction that occurs is: Neither carbon nor UC, could be detected as dissolved material in the bismuth. The standard free energy for this reaction may be written: In the two-phase region UC, + C, Fig. 1, the thermo-dynamic activities of UC2 and carbon are unity. The activity of uranium in this region was determined by measuring the concentration of uranium in a liquid bismuth melt in equilibrium with the two-phase mixture. This concentration was then used in conjunction with the activity coefficient data of uranium in bismuth reported by Tien et al.&apos; to determine the activity of uranium in the two-phase region, UC, + C. All of the quantities in Eq. [2] were then known, and the AG; (uc,) was evaluated. UC + UC2. For the studies involving UC + UC,, the reaction taking place when the two-phase mixture is brought to equilibrium with liquid bismuth is: The standard free-energy change for this reaction is given by:

Jan 1, 1969

By P. Crowther, G. J. Lamprecht

The solubilities of silver, zinc, and cerium in liquid sodium, in the temperature ranges 100 to 270°C, 190° to 550°C, and 120" to 460°C, respectively, have been determined. From the solubility data the heat the entropy the partial molal enthalpy of mixing the excess entropy and the partial molal free energy of solution for the systems Nu-Ag and Na-Zn have been calculated. For the system Na-Ce the observed negative is discussed in terms of the solubility of the oxide Ce2O3. In an earlier publication the results obtained in the study of the solubility of tin&apos; in liquid sodium are presented, as well as the detailed analytical procedures used. 1) REAGENTS Spectroscopically pure metals as supplied by Johnson Matthey and Co, were used to produce the following tracers: 253-day Ag110, 245-day zn65, and 325-day ce141. The tracers were prepared by irradiation in a thermal neutron flux of 4 x 10 13 neutrons cm-2 sek-1. To obtain a uniform amount of the required specific activity, needed for each solubility experiment, the radioactive metal was diluted with the corresponding inactive metal, by melting them together in an inert atmosphere. The liquid sodium used contained 11 ±2 ppm of O,1 determined by the vacuum distillation method.&apos; The oxygen was assumed to be present as the oxide NaD. 2) THE SYSTEMS: SODIUM-SILVER AND SODIUM-ZINC Plots were made of the log of the mole fraction of silver, Fig. 1, and of zinc, Fig. 2, dissolved in the liquid sodium vs reciprocal absolute temperature. The equations for the solubilities, based on the least-squares fit to each plot, are: where Xi is the mole fraction metal dissolved in sodium, T is the absolute temperature, and s is the standard deviation in the value of log Xi. The heats and the entropies lution were calculated from the solubility data by In neither of the two cases was any intermetallic compound formed between sodium and the solute metal as was the case for tin.&apos; Thus, for the silver and zinc systems the pure metal was taken as the reference phase. Since the solids in equilibrium with the liquid sodium were the pure metals, one can calculate the partial molal enthalpy of mixing and

Jan 1, 1969

By John Kostuik

"This paper discusses the outlook for uranium resources, and comments briefly on the measures needed to meet market objectives. Areas of recent exploration interest are also discussed.THE PREVIOUS SPEAKER has capably described the truly phenomenal growth in demand for energy from all sources. The basic factors -population growth and industrial development -which will create energy demand are so fundamental to national economies that the ascending energy demand curve will be little affected by short-term factors.Because of the economic and practical advantages of nuclear power and the degree of present acceptance by electric utilities, there is no doubt that uranium will be a principal source of primary energy in industrial countries -and this will happen within a decade. Indeed, during this period it will be the fastest growing source of energy, capturing, for example, more than half of the electric utilities' expansion in the United States by 1980. The ready availability of energy sources from domestic and foreign resources is so essential to industrial nations that the long-range outlook for their adequacy is of prime importance. There has been international concern about the availability of uranium resources at reasonable cost to adequately support and foster the development of the nuclear power industry. Canada, fortunate in having established reserves and a potential in excess of any forseeable domestic demand, can confidently look forward to being a principal supplier to the industry."

Jan 1, 1969

By A. C. Ross

"The paper will deal with non-destructive testing in general, and its advantages to those responsible for the maintenance of wire rope. An outline of the main features of the M.D. 6 Defectograph will be given, and the method of operation and results obtained will be described.The instrument will accommodate ropes at 7 /16-to 2 %-inch diameter at reasonable speeds, and is capable of detecting the most minute defects in even the largest-diameter wire ropes."

Jan 1, 1969

By A. M. McKim, J. S. Ambler

"The iron ore of the Scully Mine is upgraded from 36 per cent Fe to 66 per cent Fe through single-stage crushing, wet autogenous milling, sizing by vibrating screens and two-stage spiral separation, followed by a process in which the concentrate is dried and then further improved by high-tension separators. The capacity of the concentrator is 17,000 long tons of concentrate per day. Discussion of the operation will recognize the special problems encountered in handling preponderantly fine ore, relate issues of interest regarding wear and review mechanical innovations found to be advantageous at Wabush. The modern trend toward big equipment, thoroughly instrumented, has been the theme of design. Effects on availability must be a consideration in this choice, and sectionalizing of circuits to minimize these consequences is as important as streamlined maintenance."

Jan 1, 1969

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry&apos;s law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2&apos;= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,&apos; using Laitinen and Liu&apos;s&apos; value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,&apos; and the equations of Wagner and Werner,&apos; the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O&apos; and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies&apos; have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969

By Hans G. Kok

At this time in the history of engineering and construction, cost indexes give weekly evidence of the sharply rising costs of labor and materials. Paralleling the rise in construction costs are the costs of plant maintenance. Automation of the modern industrial plant has permitted a substantial reduction in the total number of employees required for plant operation. Of this reduced total, however, up to one-half of the employees may be engaged in plant maintenance. Management&apos;s decision to risk investment capital for a pro- posed plant or improvement is increasingly dependent upon the engineer&apos;s ingenuity in designing plant systems and structures which will require a minimum of materials and labor for manufacture, installation, and operation and which will be maintenance-free to a maximum degree. This paper concerns itself with the structural elements of bulk material handling systems in which the foregoing factors influenced the design to a considerable extent.

Jan 1, 1969

By H. Leslie Bullock

From aluminum to zirconium, the quantitative preponderance of quartz as a gangue material is well recognized. lf this material is to be efficiently removed, its variations must be understood. Variations with temperature are especially important. Too little attention has been given to the thermal polarization of quartz. Under closely controlled conditions, electrostatic upgrading is very reliable. For efficient separation, contact charges must be fostered and charges due to radiation, surface coatings, or thermal polarization avoided. This paper lists thermal transition points of quartz and shows their effect on actual separations. Simple separation tests with all factors except temperature held constant are recommended for determining transition points. With silica making up more than 27% of the earth&apos;s crust, its oxides comprising more than 59% of all igneous rocks, and quartz accounting for most of the main free oxides, the mining engineer is in constant contact with quartz, which may occur as a valuable mineral to be purified or, far more frequently, as a gangue material to be removed as completely and economically as possible. As a means of effecting such purification or removal, dry beneficiation is becoming more and more desirable owing to local water scarcities, wet waste disposal problems, or freezing conditions. One method that has been gaining particularly rapid acceptance is electrostatic beneficiation, or the separation of dry free-flowing materials by means of opposite surface charges, differences in potential, or differences in conductivity. Electrostatic beneficiation dates back to the 1870&apos;s, but only in recent years have newly developed methods and apparatus and a growing knowledge of solid-state physics widened the field for its economical application. Because the term "electrostatic beneficiation" has been rather loosely used in the literature, it has come to include both electrostatic and electrodynamic procedures. Attracting type separators, however, in which oper- ation is based on differences of surface charge or potential, are truly electrostatic, because the separation occurs in a substantially static field set up between oppositely charged surfaces. Separations with this type of equipment may occur at potentials as low as 1000 v and seldom require potentials as high as 30,000 v. In the new contact charge dielectric separators1 the variation in charge is produced by continuous contact and separation of the particles in the moving feed stream and these charges are fostered by the use of non-conducting support and feed surfaces and by handling the feed in the form of streams of appreciable depth. This favors uniformity of feed and allows higher production rates. The distinctive surface charge differences are set up on the separation of the particles according to Coehn&apos;s Law,2 which states that equal and opposite charges are generated on the separation of any two materials in contact and that the substance having the highest dielectric constant will be positively charged. The basic contact charge concept is reliable, but all electrical charges are transient and modified by the electrical conditions of the surroundings. Pyro-electric, photoelectric and radiant effects may modify or totally destroy the contact charges necessary for efficient separation, or contact with conducting surfaces may neutralize them. Such hostile conditions must be carefully guarded against, since they have led to many costly failures in the past. The most consistent difference in surface charges to insure good separation is produced by repeated uniform contact and separation of particles in the moving stream. The thickness of the feed stream possible with this method reduces the effect of contact with the supporting surfaces, but as some contact is inevitable, the best results may be assured by having the dielectric constants of the supporting surfaces between the dielectric constants of the substances to be separated. In general, the hard smooth surface of quartz makes it an ideal substance for electrostatic separation from most minerals. For instance, with calcite, starting with a feed containing 1.9% acid insolubles, one can produce a concentrate containing 0.30% acid insolubles with a tailings containing 21.7% acid insolubles and a yield of 92.8%. The color can be held at 92 or above and the tint at 1.7 or lower. Working with specularite iron ore, laboratory work has given a concentrate of 68.8% Fe., with an iron unit recovery of 96.7%. Excellent results are also in pros-

Jan 1, 1969

By R. L. Sundeen

Trackless vehicles, as the name implies, are machines not bound to rails, guide cables, or other direction controlling devices. They include, for the most part, vehicles which are wheel or crawler (track laying) mounted. Power sources may be self contained such as diesel or battery and can be defined as non-captive machines, while connected power sources such as compressed air or electric can be defined as captive machines. Trackless vehicles are used in all phases of underground excavation, loading, hauling and dumping. Early application found most machines with digging ability used to load those with payload hauling ability. As the versatility of trackless methods became more obvious the trackless vehicle has evolved to more productive machines such as the self loading haulers commonly referred to as Load-Haul-Dump equipment. Trackless vehicles find wide use in drifting and tunneling. Ability to negotiate adverse grades is especially noteworthy. Experience drawn from highly efficient room and pillar mining operations has lead to relatively wide application in drawpoint and cut and fill mining.

Jan 1, 1969

By R. R. Judd, H. W. Paxton

The rate of dissolution of cementite was studied in three low-carbon materials: a zone-refined Fe-C alloy, an Fe-0.5pct Mn-C alloy, and a commercial low-carbon steel. The materials were spheroidized, ad then held isothermally at temperatures above the Al. The isothermal anneal was interrupted periodically by a water quench and the specimens were analyzed by quantitative metallography for the amount of aus-tenite formed during the anneal. The results of this study were compared with an analytical model for the process, which assumes that carbon diffusion in aus-tenite is the rate-controlling step for the cementite dissolution process. The correlation between the model and the experimental data is excellent for the zone-refined Fe-C alloys; however, the Fe-0.5 pct Mn-C alloys and the commercial steel deviate from the calculated model. This deviation is thought to be a result of manganese segregation between the carbide and the matrix. The rate of nucleation of austenite at carbide interfaces was reduced by the manganese addition and enhanced by the presence of ferrite-ferrite grain boundaries. PREVIOUS investigations of the nucleation and growth of austenite from ferrite-carbide aggregates are not entirely satisfying for at least one of several reasons. The most prevalent of these is a lack of quantitative data. Engineering studies have been run on many steels with little control over important parameters such as composition and initial aggregate structure. The data obtained are valid only for material with identical chemistry and thermal history. A more informative approach to the problem of aus-tenitization would be to determine the mechanism that controls the rate of solution of carbide in austenite and how it is modified by alloying elements. This information could then be used to calculate an austeniti-zation rate for any material, provided its composition and structure are known. The object of the present work is to establish the rate-controlling step for cementite dissolution in Fe-C austenite and to investigate the modification of this rate by small manganese additions. The composition and structure of the material used were carefully controlled and all measurements were designed to allow a quantitative analysis of the kinetic process that controls the austenitization rate. A MODEL FOR DISSOLUTION OF CEMENTITE Cementite dissolution has been analyzed mathematically by a model that approximates the material used in the experiments. This model postulates a regular ar-array of identical cementite spheroids with 4 C( diam, embedded in a grain boundary- free ferrite matrix. The analysis provides a detailed description of the dissolution of one carbide spheroid and a generalization of the solution by summation over all the carbides in the material. The carbides may be isolated by defining identical, space-filling cells of ferrite around them. If the cell dimensions are greater than the diameter of the austenite sphere resulting from complete dissolution of the carbide, and no interaction (through diffusion in ferrite) takes place between cells during the dissolution process, the model need concern only one cell, since the solution in each cell is identical. In the experimental material, the dimensions of the cell, the carbide, and the final austenite sphere are approximately 24, 4, and 8 p, respectively; use of the single cell is therefore justified. The experimental observations are made on the austenite nodules that form around each carbide during the dissolution process. The model concerns the growth of these austenite nodules. The attendant shrinking of the carbide can be obtained from the same analysis by an extension of the calculations. Several a priori assumptions are necessary to make the analysis of the growth problem tractable. They are: 1) carbon diffusion through the austenite nodule is the rate-controlling process; 2) local equilibrium exists at all interfaces, 3) the austenite nucleus that forms on each carbide instantaneously envelops the carbide; 4) during the austenite growth process, the diffusion flux of carbon in ferrite is insignificant; 5) a quasi-steady state exists in the austenite concentration field; that is, at any instant during the dissolution process, the austenite carbon concentration gradient closely approximates that for a steady-state solution; and 6) the effects of capillarity on the dissolution rate of the carbides can be neglected. Referring to Fig. 1, a mass balance at the y-a interface for an infinitesimal boundary movement gives: Where rb is the outer radius of the austenite shell, C1 and C are carbon concentrations at the interface in austenite and ferrite, respectively, see Fig. 2, is the diffusion coefficient of carbon in austenite for the concentration of carbon at the interface, and t is time. The fifth assumption permits the austenite carbon concentration to be approximated by the Laplace solution for the spherical case. Therefore, where C(Y) is the carbon concentration at r, and A and B are constants. Local interfacial equilibrium fixes the boundary conditions for the diffusion problem. They are:

Jan 1, 1969

By L. F. Bryant, J. P. Hirth, R. Speiser

The surface, gain boundary, and twin boundary energies, as well as the surface diffusion coefficient, of cobalt were determined from tests at 1354°C in pure hydrogen. A value of 1970 ergs per sq cm was calculated for the surface energy, using the zero creep method. It was possible to measure the creep strains at room temperature because the phase transformation was accompanied by negligible irreversible strain and no kinking. Established techniques based on interference microscopy were used to obtain values for the other three properties. The gain boundary and twin boundary energies were 650 ad 12.7 ergs per sq cm, respectively, while a value of 2.75 x l0 sq cm per sec was determined for the surface dufusion coefficient. In the course of a general study of cobalt and cobalt-base alloys, information was required about the surface energy of cobalt. Hence, the present program was undertaken to measure the interfacial free energy, or, briefly, the surface energy, of the solid-vapor interface of cobalt. The microcreep method was selected for this measurement because other surface properties could also be determined from the accompanying thermal grooving at grain boundaries and twin boundaries. A brief summary of the methods for determining the various surface properties follows. At very high temperatures and under applied stresses too small to initiate slip, small-diameter wires will change in length by the process of diffu-sional creep described by Herring.1 The wires acquire the familiar bamboo structure and increase or decrease in length in direct proportion to the net force on the specimen. For a specimen experiencing a zero creep rate, the applied load, wo, necessary to offset the effects of the surface energy, y,, and grain boundary energy, y b, is given by the relation: where r is the wire radius and n is the number of grains per unit length of wire. The first results obtained from wire specimens were reported by Udin, Shaler, and Wulff.&apos; udin3 later corrected these results for the effect of grain boundary energy. The grain boundary energy is determined from measurements of the dihedral angle 8 of the groove which develops by thermal etching at the grain boundary-free surface junction. For an equilibrium configuration: Measurements of the angle 8 can be made on the creep specimens4&apos;5 or on sheet material, as was done in this investigation by a method employing interference microscopy.= If the vapor pressure is low, the rate at which grain boundary grooves widen is determined primarily by surface diffusion and, to a lesser extent, by bulk diffusion. The surface diffusion coefficient, D,, is obtained from interferometric measurements of the groove width as a function of the annealing time, t. As predicted by Mullins~ and verified by experiment, the distance, w,, between the maxima of the humps formed on either side of the grain boundary increases in proportion to if grooving proceeds by surface diffusion alone. For this case: where fl is the atomic volume and n is the number of atoms per square centimeter of surface. When volume diffusion also contributes to the widening, the surface diffusion contribution can be extracted from the data by the method described by Mullins and shewmon.8 Where a pair of twin boundaries intersects a free surface, a groove with an included angle of A + B (using the groove figure and notations of Robertson and shewmong) forms by thermal etching at one twin boundary-free surface junction. If the "torque terms", i.e., the terms in the Herring10 equations describing the orientation dependence of the surface energy, are sufficiently large, an "inverted groove" with an included angle of 360 deg-A&apos;-B&apos; develops at the other intersection. The angles A + B and A&apos; + B&apos; are measured interferometrically. When the angle, , between the twinning plane and the macroscopic surface plane is near 90 deg, the twin boundary energy is calculated from the relation: 1) EXPERIMENTAL TECHNIQUES Five-mil-diam wire containing 56 parts per million impurities was used for making ten creep specimens. These specimens had about 15 mm gage lengths with appended loops of wire and carried loads (the specimen weight below the midpoint of the gage length) ranging from 3.7 to 149.8 mg. The wires were hung inside a can made from 99.6 pct pure cobalt sheet. Beneath the wires were placed small specimens of 20-mil-thick, 99.9982 pct pure cobalt sheet from which the relative twin boundary and grain boundary energies and the surface diffusion coefficient were measured. All the specimens were annealed at a temperature of 1354" i 3°C which is 92 pct of the absolute melting point of cobalt. The furnace atmosphere was 99.9 pct pure hydrogen that was purified further by a Deoxo catalytic unit, magnesium perchlorate, and a liquid-nitrogen cold trap. As a precautionary measure the gas was then passed through titanium alloy turnings which were heated to 280" to 420°C and replaced after every test period. The hydrogen was maintained at a

Jan 1, 1969

By T. Reed Scollon

Major interrelated factors to be considered in assessing the impact of air pollution control regulations on coal are: (I) the fuel and fuel-related limitations of such regulations; (2) the rate of adoption and areal scope of the regulations; and (3) the availability of fuels and fuel-burning equipment to meet the requirements. A growing number of regulations contain provisions limiting the emissions of sulfur oxides or the sulfur content of fuels or both. With few exceptions, these limitations have not yet become fully effective in those areas which have already adopted regulations, and pertinent details of future regulations or legislation for most other areas are unknown at this time. Sufficient information is not avail- able to determine the availability of low-sulfur fuels at various demand and price levels, and large-scale commercial feasibility of sulfur-oxides removal processes and equipment is believed to be some years away. Accordingly, with the many uncertainties and unknowns, it is possible at best to make only a rough assessment of the impact of such regulations or legislation on coal.

Jan 1, 1969