Search Documents

By Dale C. H. Nevison

One of the most intensive of material rivalries is the confrontation between zinc die castings and plastic injection moldings. Pressed hard by the plastics industry, zinc die casters are learning how to make parts with less material yet without sacrificing quality. The key to this new trend is the technique of Thin Wall die casting. The obvious benefits of Thin Wall are lighter weight and lower cost. Again, obviously, these are the very selling points that put plastics into many appliance and automotive parts formerly made of zinc. One of the factors that has been most conducive to the outstanding growth of plastics has been the increasingly prevalent concept that "adequate" properties are sufficient, especially if there are cost advantages. Most of modern design today is oriented around the reasonable life of a product, rather than indefinitely extended life. This is simply an acknowledgment of the existence of a design environment that pervades many areas, reflecting the life-cyclic desire for change. Too often, so-called "weight-saving" materials end up being very costly - not only in production, but in durability and dependability. Change for the sake of change usually doesn't effect a change for the better. In the majority of cases, the best bet is to design in traditional materials and minimize the material needed, while maximizing the efficiency of the production process. Component prices of products to be produced from either plastics or zinc must be studied in detail to determine which material will produce the lowest cost of manufacture. It is not uncommon for two parts, similar in appearance at a casual look, to have a considerable difference in energy requirements and production costs. Detailed cost estimates of the advantages of each material should therefore be prepared for zinc and plastic parts before the final design and material selection decisions are made.

Jan 1, 1978

By Thomas S. Jones

This Bureau of Mines publication reviews characteristics, manufacture, and uses of natural and synthetic iron oxide pigments. Supply and demand trends within the domestic industry and in foreign trade are presented for 1955 through 1976. Iron oxides are expected to continue in demand for traditional uses, and if anything, to be favorably affected by technological developments. Imports have been significant in relation to domestic production, most notably for synthetic oxides from West Germany and Canada.

Jan 1, 1978

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By M. Hertzberg

This Bureau of Mines report describes experimental and theoretical studies of diffusion flames in free convection. The cross-coupling between buoyancy-induced flows and the combustion process is explored as it relates to the size, structure, and radiative balance of flames. New data are presented for the size-dependent radiance oscillations of diffusion flames and for the angular distribution of the total radiant intensity from a small methanol pool flame. Both amplitude and frequency of the measured oscillations are compared with theoretical predictions that are based on a new view of the structure of diffusion flames. This new view, which is at variance with the traditional one, assumes uniform reaction in the diffusive mixing zone, and recognizes the significance of the role played by convective buoyancy and its duality in both aiding and impeding flame propagation. Buoyancy quenches propagation at low burning velocities, introducing a real discontinuity in the combustion rate. A "flammable volume" is thus defined as that bound between lean- and rich-limit contours. However, in the flow disturbances generated by combustion waves that consume that volume, buoyancy aids propagation by promoting the convective mixing of a new flammable volume. The measured radiance oscillations are manifestations of these propagation and remixing cycles.

Jan 1, 1978

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

The Kaiser Aluminum and Chemical Corp. announced plans to raise June ingot prices by 4 cents to 57 cents per pound. Producers? April value for 99.5 percent unalloyed aluminum ingot was at 53 cents per pound. Domestic merchants last month were quoting the metal at 48-49 cents per pound. Primary aluminum producers began restarting production facilities following the settlement of the coal strike. Noranda Aluminum Inc. recalled workers to prepare potlines for production at its plant at New Madrid, Mo., which had closed February 14, 1978 due to the shortage of coal. Eastalco Aluminum Co. resumed full capacity production at its Frederick, Md. smelter where production had been cut by 30 percent. Anaconda Aluminum Co. resumed full capacity production at its Sebree, Ky. smelter.

Jan 1, 1978

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978

By Barry James

Energy, like labour and materials, is one of the basic production inputs in the industrial minerals industry. This paper discusses the significance of the changing energy situation in Canada as it affects the industry. It is apparent that the importance of energy as a management concern has increased considerably since 1973. The importance placed on energy management today will undoubtedly be an important factor in determining company and industry sector strength and profitability tomorrow.

Jan 1, 1978

By Gary E. McIntosh

This paper will discuss a U.S. Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring of shallow groundwater systems in the Basin. (2) Monitoring of the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems. (3) Development of a regional groundwater simulation model with appurtenant subroutines to determine local effects.

Jan 1, 1978

Martin Marietta Aluminum, Inc. followed Howmet Aluminum Corp., Revere Copper and Brass, Inc. and Anaconda Co. in lifting August prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound. Prior to these moves, Kaiser Aluminum and Chemical Corp. raised its June ingot listings by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants increased July quotes by slightly more than 1 cent to 51.3-51.8 cents per pound. ARSENIC The Occupational Safety and Health Administration (OSHA) issued new standards, effective August 1, for worker exposure to inorganic arsenic, a toxic substance linked by OSHA to lung and lymphatic cancer. The new standard will limit worker exposure to 10 micrograms per cubic meter of air over an 8-hour period, a drastic reduction from the previous standard of 500 micrograms for a like period. Implementation of the new standards may be the most difficult and costly for copper smelters where arsenic is associated with the copper feed material but problems will also be encountered by producers of arsenic containing products such as for pesticides and herbicides. The new standards allow use of personal protective gear for workers as an interim measure until plant engineering controls can be put into effect.

Jan 1, 1978

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By Roger J. Berdusco

Kaiser Resources Ltd. owns and operates a 5-million-tonper- year open-pit and hydraulic coal mine near Sparwood in southeastern British Columbia. Since 1969, Kaiser has maintained a field-scale reclamation program dedicated to the reclamation of disturbances associated with past and present mining and exploration activities . Since that time, over 1400 acres have been treated using modified forestry and agricultural techniques with encouraging results.

Jan 1, 1978

By Mackenzie Burnett

Quick-Fix Blowout Stoppings were evaluated in several underground mines as an alternative to conventional ventilation control bulkheads. Blowout stoppings offer considerable savings in bulkhead construction and repair costs if the 0.1 inch H20 of differential pressure required to inflate them is available. The Quick-Fix Blowout Stoppings were utilized successfully in uranium mines in the Southwestern United States where savings in bulkhead construction and repairs to blast damaged bulkheads are estimated to equal $9,500 over the projected 2 year average life of a blowout stopping. Two types of material were evaluated. Five methods of anchoring the stoppings to drift walls were evaluated. Three methods of anchor attachment to the stopping material were evaluated. Blast pressure measurements were made in conjunction with the evaluation of the blowout stoppings.

Jan 1, 1978