Search Documents

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984

By Robert C. Gabler

Three filter cloth fabrics commonly used in drains for coal waste embankments were tested by the Bureau of Mines for clogging behavior and deterioration under simulated field conditions. The objective was to provide guidelines for the mining industry for the proper selection and use of filter cloths to assure safer embankments at mine waste disposal sites. The filter cloths were tested with three coal waste samples in stand-pipes used to simulate coal mine waste disposal environments. Two of the cloths showed a tendency to become clogged with fines from the wastes. One waste caused clogging by precipitating an iron-silicon compound on the test cloths. No apparent cloth deterioration resulted from exposures to the simulated coal waste environments. (The exposures ranged from 2 to 12 months.) In other tests, exposures to waters in the pH range of 2 to 12 and to reagents used in coal-preparation plants resulted in insignificant or no deterioration, as measured by tensile strength. However, long exposures to sunlight (ranging from 4.6 to 6 months) caused major deterioration in two of the cloths (86-and 98-pct losses in tensile strength) and slight deterioration in the third cloth (9-pct loss in strength).

Jan 1, 1984

Jan 1, 1984

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By R. C. Burtan

Long before the dawn of recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It has been well established that prehistoric man discovered flint. "The Flintstones" were aptly named. The flintknappers of southern England and Wales still exist today in ever dwindling numbers as they seek out chunks of flint. It is a well known fact that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica containing materials have a great many uses in modern society. However, this material is potentially extremely hazardous to our health. Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. It is obvious to us that he was describing silicosis. It is also apparent from ancient writings, that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century, B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. It was certainly described by Agricola in his "De Re Metallica" published in 1556, in which he described lung disease among hard rock miners. This publication, I'm sure, is of special interest and perhaps known to many of you in the mining community. The original document was written in Latin and was translated in 1912 by two gentlemen, Hoover and Hoover. One of these translators was Herbert L. Hoover, a former president of the United States, who made his living before his presidency as a mining engineer.

Jan 1, 1984

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984

By Peter T. Chiang

A brief literature review on metal separations by ion exchange and solvent extraction of their thiocyanate complexes which are practiced in analytical chemistry as well as in industries was performed. Owing to the poor stability of free thiocyanic acid in acidic aqueous and organic media, technical and environmental problems which cause high thiocyanate consumptions often arise during the practice of the separation processes. This prompted the conducting of a second and more thorough literature review on the chemistry of thiocyanic acid. The objectives of this undertaking are to compile and interpret literature data on the physical properties and chemical reactions of thiocyanic acid, thus providing a clearer understanding of the causes of these problems and giving options as to how to minimize them. The best answer found for carrying out the separation processes is to keep the temperature, thiocyanic acid concentration and total acidity as low as practical.

Jan 1, 1984

By Mahesh C. Jha

Arsenical gold ores occur in many parts of the world, including numerous mines in Canada and the western United States. Free gold is often finely disseminated in the grains of sulfide minerals, arsenopyrite, pyrite, orpiment and realgar. Generally a sulfide concentrate is produced by flotation. Arsenical ores or concentrates are not amenable to direct cyanidation and therefore are considered refractory. A wide variety of roasting equipment and conditions have been used by the mills to remove arsenic and sulfur from these concentrates. The resulting calcine is easy to cyanide and gold is recovered from the cyanide solution by zinc dust cementation. Room-temperature potential-pH diagrams and high-temperature phasestability diagrams are presented to discuss the chemistry of the gold cyanidation, cementation, and roasting steps in the presence of arsenic. The environmental aspects of arsenic discharge are also included.

Jan 1, 1984

By P. R. Bremmer

As part of a program to devise alternative technologies for producing alumina from domestic resources, the Bureau of Mines investigated the leaching of calcined kaolinitic clay to form basic aluminum chloride solutions. Bench-scale experiments were conducted for single-stage batch leaching with AICl3 solution and three-stage countercurrent leaching with substoichiometric HCI. Variable conditions of clay calcination and leaching were studied to determine their effects on aluminum extraction and pregnant liquor composition,

Jan 1, 1984

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By J. M. Kaufman

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is linited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized.

Jan 1, 1984

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By B. Pina

The conversion of maf coal to pyridine solubles and gas was investigated in a microautoclave batch reactor for two Kentucky washed coal samples (Ky. #9 and Ky. #11). Solvent hydrogen donor strength was controlled by the tetralin content of a mixed 1-methyl naphthalene-tetralin solvent. Primary liquefaction conversions greater than 90% in 10 minutes of reaction time at 427°C were achieved in liquefaction solvents with moderate hydrogen-donor strength (circa 40% tetralin). A modified irreversible first order rate expression, containing a parameter (a) to account for the intrinsic reactives of the maf coal, described the experimental kinetic data rather well. The integrated form of this rate expression is -k1e x = a (a- ß)e (eq. 1) Parameter ß in equation (I) is the pyridine solubility of the starting maf feed coal, x is the primary liquefaction fractional number of conversion, k1 is the specific reaction velocity constant and ? is reaction time. Primary liquefaction rate was found to be quite temperature sensitive and independent of coal when a liquefaction solvent containing 40% or more tetralin was employed. Primary liquefaction rate appears to depend on liquefaction solvent hydrogen donor strength for solvents containing = 40 wt.% tetralin. The intrinsic reactives in the maf feed coal or a appear to depend mainly on the inertinite group maceral content of the coal for the two coals studied in liquefaction solvents containing 3 40wt.% tetralin. In contrast, a appears to decrease in liquefaction solvents of low donor strength., i.e; solvents with less than 40wt.% tetralin.

Jan 1, 1984

By Dean S. Rogers

The conventional role of exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Nine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1984

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By M. A. A. de Klaver

Due to the current cost and availability of crude oil in Brazil, Samarco Mineracao S. A., as part of its program of quality and productivity optimization and reduction of operating costs, has undertaken tests to utilize alternate energy sources for fuel oil used in its pelletizing plant at Point Ubu, Espirito Santo, Brazil. The energy program undertaken by Samarco consists of two basic steps. The first step was to reduce energy consumption, that is, to improve the thermal efficiency of the process. Secondly, a program was started to substitute the fuel oil with coal.

Jan 1, 1984

By J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Company to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the Company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received substantial attention in recent years. A Company guideline that no coal shipment shall exceed any contract or company-imposed coal quality specification has been successfully implemented. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed. Background Surface coal mining of subbituminous C rank coal in the Cillette. (Campbell County) Wyoming area has become increasingly competitive during recent years. Prior to 1974, one small surface mine produced coal for local consumption. During the last ten years, 13 new surface coal mines have been constructed. Coal production from Campbell County, Wyoming totalled 88 million short tons (79.8 million metric tons) in 1983, the majority being shipped to electric utilities in the central and southern United States via unit trains having a capacity of 10,000 short tons (9,072 metric tons).

Jan 1, 1984