Search Documents

By Hungerford F

Long-hole drilling technology has rapidly advanced this decade beginning with rotary drilling/pump down camera surveying and culminating in down-hole motor drilling with cableless electronic surveying over the past two years. With the latter system, a high level of directional control is achievable in boreholes up to 1000m long. Past long-hole drilling across the industry has seen a mixture of success and failure. With these experiences, new and improved techniques and equipment have evolved. A number of long-hole drilling options are available as variations on the basic rotary and down-hole motor methods. They involve different levels of cost and equipment and vary in their suitability in different geological environments and definition of targets. Long-hole drilling is mainly target applied, either in defining geological structures in greater detail, or proving important mining areas such as longwall blocks, to be free of structures. Successful drilling hinges on a combination of drilling expertise, quality and appropriateness of equipment, understanding of geological conditions and good colliery support. Drilling expertise forms part of sound interpretation through keeping relevant records, understanding the reasons for changes in drilling conditions and implementing specific tests such as coring. The final interpretation builds upon all other available geological information. There is still scope for research into improved techniques and equipment. The use of long boreholes for geophysical surveys has high potential.

Jan 1, 1988

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By Shigeo Asai

"Electromagnetic processing of materials is newly proposed to be considered as one of the engineering fields where functions of electromagnetism are utilized for processing electrically conducting materials, such as liquid metals, electrolytes and plasmas. The background requiring this processing and the engineering characteristics supporting it are described. The applicable functions of electromagnetism to material processing are revealed from the view point of magnetohydrodynamics. The existing processes and the proposed ones are classified into utilized functions and engineering applications are discussed. IntroductionElectric energy has been used in the metallurgical field for the processes of melting, refining and solidification. In these cases both the magnetic field which is induced by an imposed electric current, and the electric current are applied on electrically conducting materials such as molten metals. Thus, it turns out that the magnetohydrodynamic (MHD) phenomena have unconsciously been seen in metallurgical processes using electric current. The academic backbone studying MHD phenomena is the Magnetohydrodynamics which is being developed in the fields of plasma physics, astrophysics, fusion research and nuclear energy.The first attempt where magnetohydrodynamics was intentionally applied on metallurgy was a Symposium of IUTAM (The International Union of Theoretical and Applied Mechanics) in titled as ""Metallurgical Applications of Magnetohydrodynamics"" at Cambridge, UK, 1982 [1]. This timely event stimulated a few metallurgists to recognize the importance of ~MHD and was a good warning to the metal societies in the world. Especially in Japan, the Steelmaking Investigative Subcommittee of Research Planning Committee in the ISIJ (The Iron and Steel Institute of Japan) discussed the application of ~IHD to metallurgy and selected it as one of the four major innovative subjects for future steelmaking technology in Japan [2]. Indeed, the term of ""Electromagnetic Metallurgy"" itself was firstly coined by this subcommittee. Upon the request of a report from the subcommittee, the ISIJ has established a committee on ""Electromagnetic Metallurgy"" at 1985, under the author's chairmanship."

Jan 1, 1988

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

Blasting is at first sight a simple operation. Blastholes are drilled in a suitable pattern, primed, charged with explosives, stemmed and finally the blastholes are connected together to give the appro- priate initiation sequence. In practice the action of the explosive takes place in the interior of an opaque rock mass and only the external faces of the rock mass to be blasted can be easily observed. The mechanisms of blasting cannot be observed directly and must be inferred from observations of the free face and meas- urements of particle movement made by sensors grouted into holes in the rock. Explosives react very rapidly, in some microse- conds and any instrumentation of a blast must have an appro- priate response time. In many mines several rock types can be encountered during production. Several different methods of blasting may be necessary to cope with changes in rock types espe- cially if weak rocks are found in the final limits. This also makes it difficult to be sure of getting a large enough volume of rock to perform a series of reproducible experiments. While there appears to be agreement on the mechanism of blasting it is unlikely that a detailed understanding of how all the variables that can be encountered in practice affect blasting. The ease of assessment of the results of blasting depends on the criteria used. It is easy to isolate, measure and count over- size boulders. It is however difficult and costly to get a complete fragment size distribution. Methods used to assess blasting can vary significantly from site to site and the ways in which data are collected, presented and analysed will vary making compari- son of blasts at several locations very difficult. The definition of an optimum blast can also vary with the type of blasting. The muck-pile profile and fragmentation will be different for a dragline to that for a truck and shovel operation. In order to be able to assess blasting the mechanism has to be understood. Th rock and explosive properties considered rele- vant to blasting can then be determined. This paper discusses the generally accepted mechanism of blasting. The on-site observa- tions to assess blasting are-then listed. The mechanism of blast- ing can also be modelled and the use of modelling to optimize hlaetina ie thPn Aiernccarl

Jan 1, 1988

By M. Misra, I. Anazia

The dispersion of oily collector has a significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. Such dispersion and reagent addition techniques are invariably inadequate and nonselective. A new collector addition technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This technique involves atomization of the collector into the air stream. Under these circumstances, an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the air phase (continuous with respect to oil), and the air phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and, most significantly, increases the flotation rate of ultrafine coal. Atomization of collector/frother combinations yielded improved flotation recovery and maintained near uniform froth levels, which is a desirable feature in coal flotation. Microscopic examinations of the attachment of oil- coated bubbles at a coal surface were conducted by attachment time and contact angle measurements. Oil-coated bubbles attach at significantly faster rates and with a higher contact angle than oil-free bubbles.

Jan 1, 1988

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By Robert B. Parsons

"This article is based on a paper presented by Jim Scott at the 1988 annual convention of the Prospectors and Developers Association of Canada. The paper suggests a number of factors that might be taken into account in negotiating royalty terms.IntroductionRoyal ties are a part of mining life in Canada. They are used by many kinds of individuals in many kind s of situations. Prospectors commonly take royalty interests back when they transfer claims to development companies. Mining companies disposing of undeveloped (or sometimes even developed) properties are often paid at least in part by royalties. Royalties are even used by institutional investors with no other connection with the resource industry.Such different royalty holders have different investment goals, different cash flow requirements, and different risk / return preferences. These differences have given rise to a number of different royalty type s. These types range from the simplest cents-per-ton royalty (where the operator pays a royalty at a fixed rate per ton milled) to net smelter return or ""NSR"" royalties (where the royalty is based on a percentage of the operator's NSR) all the way to net profit interest or ""NPI"" royalties (where the royalty is based on the operator's bottom-line net profit),The fundamental difference between the many royalty types is in the risk/ return relationship. The cents-per-ton royalty, for example, is relatively risk-free. Of the many economic factors which affect a mine, the only one which will affect the royalty holder is the amount of ore physically milled. On the other hand, the potential for significant gains under a cents-per-ton royalty is also very limited. The royalty holder will not share in any increases in the market price of the end product or any cost reductions achieved by the producer."

Jan 1, 1988

By X. Shi, N. S. Dala, V. Vallaythan

"Cellular damage induced by silica dust is known to be associated with increased fragility and destabilization or destruction of the cell membranes. The mechanism by which silica dust effects biological membranes is still unknown. Using the ESR spin-trap methodology, we find that hydroxyl radicals are generated in aqueous suspensions of freshly ground silica. The amount of the radicals generated depends on the extent of grinding and ""freshness"" of the dust. Using linoleic acid as a model lipid, we show that the silica dust causes lipid peroxidation via ·OH, 02-, or linoleic acid related radicals as intermediates. Catalase and superoxide dismutase inhibit the formation of these radicals. The results suggest that free radicals associated with freshly ground silica and the related lipid peroxidation of the memberanes may be the starting point of the silicotic processes.INTRODUCTIONDespite considerable-effort over the years, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrosis are still not fully understood (1,2). It is generally thought, nevertheless, that the interaction of the quartz particles with the cell membranes is the starting point of the silicotic process (3). We felt that the mechanism of the membrane damage by quartz might involve oxygenated free radicals because (a) a suspension of quartz particles in contact with alveolar macrophages has been reported.(4,5) to initiate an enhancement of lipid peroxidation, defined broadly as the ;oxidative deterioration of polyunsaturated components of lipids, and (b) hydroxyl (·OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (6) and initiating lipid peroxidation in lysosomal membranes (7). Moreover it is known that exposure of cell membranes, fatty acids and unsaturated food oils to ionizing radiation, which generates ·OH. radicals, causes rapid peroxidation (6). Earlier studies o~ the aqueous chemistry of quartz suspensions have reported detection of HzOz (8), implicating the formation of ·OH radicals as transient species, but, we are not aware of any report of the detection of ·OH radicals in quartz suspensions and this provided the motivation for the present undertaking. Since it is known that, because of their high reactivity (hence short life time) in aqueous media, the ·OH radicals cannot be detected via electron spin resonance (ESR) directly (9,10), we have used ESR combined with the spin-trap methodology (9) for studying the •OH formation."

Jan 1, 1988

By Thomas M. Barczak

This report describes a study that examined load transfer mechanics in longwall shield supports as part of the Bureau of Mines research program to optimize support design and utilization. The objectives of this study were to determine the contribution of the leg cylinders and the caving shield-lemniscate assembly towards full shield vertical and hor-izontal load resistance capability and to determine how the interaction of these members affect overall shield response. Load-displacement characteristics of the leg cylinders and the caving shield-lemniscate assembly, independent of the full shield, were evaluated from controlled displacement tests in the Bureau's mine roof simulator and responses were compared with full shield responses to identify load transfer mechanics. It is concluded from this research that the participation of the caving shield-lemniscate assembly significantly affects the response of the shield support. It is likely that the caving shield-lemniscate assembly is not participating fully in current shield designs because of translational freedom in the numerous pin joints. It is also concluded that the shield will respond differently to different boundary condi-tions resulting from interaction with the strata. This report describes load transfer mechanics of shield supports and the implication of these research findings on shield design and utilization.

Jan 1, 1988

By David G. Borg, John Bussey

The new AIRDEK (tm) technique for pre-splitting in surface coal mines produces highwall conditions that have greater safety with lower costs for explosives, labor, and drilling. Successful applications have been made in highwalls ranging from 20 to 100 feet or more and in blasthole diameters from 3-1/2 inches to 12 inches.

Jan 1, 1988

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By O. J. C. Runnalls

"Canada became the world's largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada's uranium resources will grow because of the foreseen growth in the world's installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988

By Gregory M. Molinda

Coalbed discontinuities historically have been hazardous to mining as well as obstructions to efficient production. An effective means of mapping these features is needed in order to plan safe and efficient mine development. This Bureau of Mines report discusses the use of surface seismic techniques for this purpose. At a southwestern Pennsylvania mine, a system of coalbed discontinu-ities (paleochannels) was accurately mapped by the Bureau of Mines using borehole log methods and underground observation. This site was chosen to test the value of a high-resolution surface seismic reflection on technique for coalbed mapping. A statistical study performed at this mine indicated that the probability of accurately delineating this paleochannel system with conventional borehole methods was remote. A total of 1.47 miles of high-resolution seismic survey, comprised of four seismic profiles, was conducted in known and suspected coalbed discontinuity areas. Several test holes were drilled on the seismic lines in order to evaluate the interpretations. It was found, based on these and other existing boreholes, that it is possible to predict these dis-continuities. Paleochannel washouts were correctly predicted in several instances but in other instances were either incorrectly predicted or not predicted in areas of known discontinuities.

Jan 1, 1988