Search Documents

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By S. Horton, F. L. Stanley, P. J. Bethell

Introduction The McClure River Processing Plant is located at McClure in Dickenson County, VA. The plant was originally constructed in 1979 as a 600 st per hour facility. The plant is fed by coals from numerous mines in the area as well as a major longwall mine onsite. Coal is processed predominantly for the metallurgical coal market. The original plant was comprised of three separate processing circuits incorporating a heavy medium vessel for the coarse material (+10 mm). Intermediate sized material (10 x 0.6 mm) was beneficiated in heavy medium cyclones, with the remaining fines (0.6 mm x 0) passing to froth flotation for upgrading. The products from all three circuits were combined prior to thermal drying and then stored in silos or ground storage prior to shipment to the metallurgical coal markets. A middlings heavy medium cyclone circuit was also present to rewash the vessel and primary heavy medium cyclone rejects. The original circuit is as shown as Fig. 1 (Editor's note: All figures are reproduced at the end of this paper.) In reasonably close proximity to the McClure Plant is the much older, less efficient Moss 1 Plant, (Chance cone, table, water only cyclone, froth flotation, Fig. 2), which prior to the McClure Plant expansion was processing considerable tonnages of coal. At that time, the McClure River Plant was processing coal at the maximum possible feed rate, and the Moss 1 Plant was finding increasing difficulty in maintaining the stringent quality specifications on its major metallurgical coal accounts. Given the fact that many of the feeder coals to Moss 1 could be moved with minimal difficulty and cost to McClure, an exercise was conducted to evaluate the potential of expanding the McClure Plant. This would result in transferring coals from Moss 1, thereby increasing yield, reducing operating costs, and enabling customer specifications to be met more easily. After evaluating many possible ways of expanding the McClure Plant, we eventually settled on an approach based on the idea of Gallagher at German Creek in Australia (Gallagher, 1986). Our objective was to increase plant capacity by removing the coarser size fractions (0.60 x 0.15 mm) from froth flotation and at the same time eliminating the finer fractions (1.25 x 0.6 mm) from the heavy medium cyclone circuit, thereby allowing these circuits and therefore the plant as a whole to increase its capacity. These size fractions (0.60 x 0.15 mm from froth flotation and 1.25 x 0.6 mm from the heavy medium cyclone circuit) would be treated in a new spiral circuit. After desired evaluation of the various circuit capacities, including desliming screen, clean coal filter and thermal dryer capacities, etc., it was concluded that we should be able to maintain high levels of processing efficiency in the existing circuitry while at the same time expanding plant feed rate from a nominal 600 st per hour to 1000 st per hour, thereby achieving the objectives The circuit that was finally settled on is shown in Fig. 2. Several unique features were incorporated in this circuit in an attempt to maximize processing efficiency and reduce maintenance costs. First, the idea of a single-stage spiral circuit was abandoned in favor of a two-stage circuit incorporating rewashing the primary spiral middlings in a secondary spiral (Bethell, 88). The spirals selected were Mineral Deposits Model LD4 units. It was felt, after much previous testing, that spiral middlings rather than being a true middling gravity fraction were in fact a combination of true middlings with a preponderance of misplaced light coal and high-density rock. Consequently the insertion of this material directly into either clean coal or refuse streams (per normal practice) would only lead to loss of efficiency. The operating philosophy behind the design of the circuit was to produce the purest coal and rejects possible by adjusting the spiral splitters. Misplacement of refuse into the clean coal and vice versa would be minimized by taking a fairly large middlings cut. By reprocessing this material (10%-15% of primary spiral feed) in a secondary bank of spirals the misplaced material in the primary middlings would be reprocessed and its probability of reporting to the correct stream greatly enhanced. To minimize fines loading on the spirals, fine aperture sieve bends were to be included. A further novel feature of the circuitry is the desliming/ dewatering system. A philosophy of accepting inefficiency but forcing it to work in our favor was developed. The dewatering screens (Linatex Combis) were chosen not for their ultimate screening efficiency but for their ability to remove slimes (tolerating a fair quantity of oversize in the effluent) and their enhanced maintenance characteristics. Any oversize passing into the effluent, together with the fine coal centrifuge effluent, would pass to classifying cyclones, the objective of which was to reject to overflow (and hence froth flotation) as many fines as possible (-150 µm) without running the risk of losing coarse (1.25 x 0.15 mm) material to oversize. Hence, by a process of producing a "slime free" screen product coupled with a "coarse free" cyclone overflow, sizing efficiency could be maximized. Obviously, recirculating load had to be factored into the Combi Screen design capacity. The spiral circuit as shown in Fig. 2 was installed at McClure River in January 1988. The spiral circuit efficiency was very high immediately, and, after the normal debugging, plant capacity has been increased to the point at which we are currently processing of the order of 1100 st per hour. Test program The performance of the spiral circuit has been evaluated by two major samplings of the entire new circuit, coupled with routine bi-monthly tests on all other major components of the plant circuitry.

Jan 1, 1992

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

NTRODUCTION Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for pre¬dicting the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface move¬ment data, a relatively large portion of the subsidence data col¬lected could not provide information other than surface movement. In a paper by Luo and Peng (1992), the sources and magnitude of errors in the measured surface movements using an electronic total station in subsidence survey are discussed. If the errors in the measured surface movement components are left untreated before calculation for deformation indices (i.e., slope, strain and curva¬ture), the errors will be carried over to the deformation indices and enlarged if improper numerical procedures are used in the calcu¬lation. It should be noticed that in protecting structures affected by ground subsidence, accurate surface deformation indices are much more important than surface movement. In order to improve the accuracy of the collected surface movement data and the calcu¬lated deformation indices, a number of numerical procedures are also proposed in the same paper. The proposed techniques include: a data smoothing technique for data pre-processing; and a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data. DATA SMOOTHING Because of various factors, the measured surface movement data always contain errors, small or large. In order to better utilize the collected data, a data smoothing method is proposed to correct the errors in the measured movement data. The method uses the same concept as the influence function method (e.g., Knothe, 1957) on which many existing subsidence prediction methods are based. The data smoothing method makes necessary corrections on the measured movement for the point of interest according to not only the measured movement at this point but also those at the surrounding points. The contribution of a surrounding point in making the correction for the point of interest is inversely propor¬tional, in exponential form, to the distance between them. The new magnitude of a movement component at the point of interest (Zi*) is calculated by

Jan 1, 1992

By N. Agron-Olshina

The application of the QEM*SEM image acquisition and analysis system to the measurement of the mineral matter in coal and the materials in fly ash is described. A new sample mounting technique was developed using iodinated epoxy to provide a backscattered electron contrast between the coal, the mounting medium and the mineral matter. Several comprehensive and detailed species identification programs for silicate minerals and materials were developed to analyse the 1000 count x-ray spectra used for the measurements. Case studies are presented to demonstrate the capabilities of the new technique to distinguish different coals and fly ashes by their mineral and material composition rather than by conventional chemical analysis. Applications of the new technique are aimed at demonstrating that composition and size distributions obtained from OEM*SEM measurements can be used: 1. to characterize coal with respect to combustion problems in power stations, 2. to characterize coal for fine coal cleaning, 3. to characterize fly ashes in relation to problems such as erosion in combustion systems and the ease of precipitability in dust collection facilities, 4. to refine the classification systems used in marketing coal for pulverized fuel firing and fly ashes as a component of cement and building materials.

Jan 1, 1992

By J. S. Kirkaldy

A theoretical procedure is demonstrated for calculating two-dimensional binary cellular single-valued interfaces and extended to triple-valued (remelt) shapes. The numerical calculations for the single-valued local equilibrium problem which yield unique shapes as functions of the supersaturation parameter a and the partition coefficient k are reviewed. The cell amplitude L and wavelength A scale identically as the inverse velocity to the 112 power and the aspect ratio r is a constant equal to 312, independently of a and k for a < 0.5.. For 0.5 < a < m, L, A and r decrease asymptotically to zero indicating the finite amplitude nature of the instability at a = 1 and the existence of sub-marginal states which converge to a flat interface at a- m (Glv- m). Scaling comparisons between equilibrium single-valued and triple-valued and deep-rooted non- equilibrium cells are made.

Jan 1, 1992

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By L. M. Cenegy

Introduction The formation of scale is common in gold ore processing plants. A working definition of such scale is: "A hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water." The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem. The problem of scale in carbon strip circuits Carbon strip circuits present a particularly challenging scale inhibition problem. Many of the factors that tend to promote scaling are present in these systems. For example, carbon strip circuits are run at high temperatures and high pH levels and require long batch cycle times. Tortuous paths are encountered by the strip solution circulating through heat exchangers, pipes and elbows, causing transient pressure drops throughout the system. Severe conditions such as these cause the water to possess a high scaling potential and may lead to the breakdown of some of common types of scale inhibitors. Formation of scale Natural waters contain dissolved minerals and gases that promote scaling. One of the contained gases, carbon dioxide (CO2), is an important factor in scale deposition. Carbon dioxide dissolves in water to yield carbonic acid according to the following reaction: [CO2 + H2O - H2CO3 (carbonic acid)] Carbonic acid rapidly dissociates to yield bicarbonate and carbonate ions depending on the pH of the system: [H2CO3 -s H+ + HCO-3 (pH range 6-10) HCO3 -a H+ + COO (pH range > 9)] In gold cyanidation processes, lime is added to raise the pH of the mill solution to 10 or above to promote cyanidation of the gold and to eliminate the possibility of hydrogen cyanide (HCN) formation. Lime contributes both hydroxyl ions (OH--) and calcium ions (Ca++) to the solution. The normal scale forming reactions in mill water systems were described by Beasley (1973) as: [HCO-3 + OH -s C03 + H2O Ca++ + C03 -a CaCO3] Factor affecting scale deposition According to Linke&apos;s (1958) solubility tables, the solubility of calcium carbonate in carbon-dioxide free water is only 13 mg/dm3 (13 mg/L) at 25° C (77° F). Scale deposition occurs when the concentration of calcium and carbonate ions in the solution exceeds the solubility of calcium carbonate. This occurs, in most cases, when the water has undergone some chemical or physical change. Some typical changes that might occur that lead to scale deposition are discussed below. Temperature An increase in temperature can greatly increase the tendency to form calcium carbonate scale. Studies by Miller (1952) have indicated that calcium carbonate is less soluble at higher temperatures. Hence, high temperatures promote scaling. For this reason, scale is often noticed on heat exchangers, autoclaves and other high temperature surfaces. Pressure A decrease in pressure may lead to an increase in the tendency to form calcium carbonate scale. Fulford&apos;s (1967) work has shown that scale is more soluble at high pressures. Hence, scale is likely to be prevalent in pump suction lines, elbows, baffles and other areas that produce turbulence and subsequent pressure drops. Change in pH Calcium carbonate scale is pH dependent and tends to form more readily at high pH. Any event that causes an increase in pH, such as the introduction of lime or caustic, would tend to initiate scale formation. Since most gold recovery operations are run at a pH above 10, the tendency to form calcium carbonate scale is always great. The use of scale inhibitors to prevent calcium carbonate scale Many products are commercially available to inhibit the formation of calcium carbonate scale. Some of the more effective types include phosphonates, as well as acrylate and maleate-based polymers and copolymers. Many of these products function by means of threshold

Jan 1, 1992

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner&apos;s treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By Y. Luo

Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for predicting, the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface movement data, a relatively large portion of the subsidence data collected could not provide more information other than surface movement. In this paper, the sources and magnitude of errors in the measured surface movements and calculated surface deformation are discussed. Techniques for improving the accuracy of the calculated deformation indices (i.e., slope, strain, and curvature) are developed. The proposed techniques include: (1) proper selection of monument spacing for subsidence monitoring; (2) a data smoothing technique for data pre-processing; and (3) a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data.

Jan 1, 1992

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By R. L. Nyirenda

One of the problems with ammoniacal-ammonium carbonate leaching of EAF carbon steelmaking flue dust is that zinc present in spinel phases is not leached. This paper presents results of test work in which prior to leaching, EAF dust was reduced with CO containing gas to decompose the spinels into zinc oxide and iron bearing phases, mainly metallic iron and wustite. From such reduction products, the amount of zinc leached increases but the iron co-leached becomes extensive. The effect of various leaching parameters such as liquor concentration and redox potential on zinc and iron dissolution has been investigated. Supplementary experiments utilizing pure zinc oxide and pure iron phases were also carried out. Results show that the co-dissolution of iron from severely reduced EAF dust cannot be prevented. This is because the wustite phase contains zinc which can only be leached when iron also dissolves. Further, the zinc bearing wustite phase is not totally soluble so that the residue cannot be made zinc free. In the absence of air, dissolution of metallic iron hardly occurred, though in leaching experiments of a long duration its transformation to a spinel structure was observed.

Jan 1, 1992

Halide media are considered as suitable alternatives to cyanide for extracting gold and have received much attention lately. The extraction of gold by iodide-iodine mixture has been patented and briefly studied without much attention given to the fundamental aspects of this process. This paper reports recent studies on the kinetics of gold extraction in iodide media, using hypochlorite, iodine and hydrogen peroxide oxidants. The kinetics of dissolution was found to be dependent on the solution pH, reagent concentration and most importantly the iodide- oxidant molar ratio. Without proper control, the gold surface can be passivated due to the formation of solid products. Thermodynamic modelling was carried out to determine the equilibria governing the dissolution process. The formation of AuI solid was also identified as a possible product during the dissolution.

Jan 1, 1992

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By R. H. Hanewald

The INMETCO process has been modified so as to recover nickel. chromium and Iron from a wide variety of metal containing waste-streams. This now includes the recovery of metals from spent acid solutions such as chromic acid etching I1quids. nJcke1 and chromium plating solutions; stainless and superalloy pickling solutions. etc. In addition. hazardous electric furnace stainless steel and. superalloy baghouse bags can be processed so as to recover the valuable metall1cs. A detailed review of the above new recovery techniques w1ll be discussed as well as the current operating methods used at INMETCO.

Jan 1, 1992

By G. E. Maryniak

To date, human space exploration has been almost completely dependent on the use of resources carried with astronauts and cosmonauts from the surface of the Earth. The only exception to this has been the harvesting of solar energy to power space stations like Skylab, Salyut and Mir for long-duration missions. This dependence on materials which must be transported into orbit at costs in excess of $5000 per pound is the fundamental limiting factor in space exploration and operations. It is likely that launch costs can eventually be greatly reduced by means of such innovations as true single stage to orbit vehicles, aerospace planes, or serial electromagnetic or laser launch systems. However, the Earth will always remain an expensive source of materials for space construction and for basic commodities such as propellant and life support liquids and gasses. Fortunately, abundant sources of materials exist which are already in space, outside of the Earth&apos;s deep gravity well.

Jan 1, 1992

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992