Search Documents

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By Bruce Vandenberg, Andy Battfay, Don Lake, Steve Conway, Jeff Yorsz

"High-speed motion pictures are an invaluable resource for blasting analysis. Whether processed by the human eye or a computer, this imagery can provide important insight into a blast and its effects.While certainly popular, traditional high-speed film cameras hamper this process. Instant feedback is not available since film requires developing and, relevant in the case of automated analysis, film isnot immediately compatible with a computer. With these facts in mind, a new high-speed video camera system, the SVCSOO, has been developed. The SVC500 combines the capabilities of a high-speed film camera, the convenience of a solid-state digital video camcorder, and the computing power of a ‘486 PC to provide a complete, standalone platform for high-speed image acquisition and analysis. This paper will describe the design, features, and use of the SVCSOO andcompare these with the analogous aspects of film cameras."

Jan 1, 1994

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By Stella Sigler

This publication contains analyses and related source data for 153 natural gas samples from 16 States. Of the total samples, 149 were collected during calendar year 1993. The remainder were collected earlier, but releases granting permission to publish were not received until 1993. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1994

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

By P. R. Taylor

Recent research by the investigators has evaluated the oxidation roasting of refractory gold concentrates in the presence of hydrated lime. (Taylor, 1990, 1991, 1992, 1993). These results have indicated that it may be possible to roast concentrates in such a way as to contain nearly all of the sulfur and arsenic in the roaster calcine and that cyanidation may be possible. To further evaluate the behavior of this type of roasting system a laboratory cyclone reactor was built and operated using pyrite and hydrated lime as a .model system. Approximately 50 years ago, the principle of cyclone firing entered practical boiler construction. The appeal of the cyclone configuration was that it afforded the flash combustion process greater efficiency due to turbulence-induced increased mass transfer, heat exchange, and combustion rates.

Jan 1, 1994

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

By J. J. Talja

An investigation of oxidation of various nickel concentrates was carried out using differential scanning calorimetry (DSC). The aim of this study was to determine the ignition temperature and investigate other oxidation behavior of various sulfide-based nickel concentrates. Variables in the experiments were mineralogy, particle size and partial pressure of oxygen with temperature increasing linearly at 25 K/min from 323 to 1023 K (50-750 °C). The igni¬tion temperature was determined to represent the starting point of rapid oxidation. The reac¬tion enthalpies of the concentrates were determined and the amount of heat generated up to various time were used to calculate the extent of reaction. Mineralogical changes at various stages of oxidation were also investigated. For this purpose a second set of DSC-experiments were carried out in which each experiment was interrupted at a desired temperature between 673-873 K. From these tests the weight loss of samples were determined and changes in the individual constituent of sulfide minerals were analyzed. For pentlandite-based Ni-concentrates the ignition temperature was 705-710 K (approximately 435 °C). Pyrite was the first sulfide to oxidize. Reactivity of the violarite-based concentrate was greater than those of the pentlandite-based concentrates. The stoi-chiometry of pentlandite changed before ignition because of preferential oxidation of iron. Rapid oxidation of the pentlandite mineral occurred at about 823 K (550 °C). By 900 K about 90 % of the iron in pentlandite was converted to hematite, and NiS containing some iron was formed.

Jan 1, 1994

By V. Ramachandran

Over the past 20 years, water treatment plants have been built at various Asarco facilities to effectively handle the process waste streams that need to be bled from the system. The current paper review the several operations with reference to (a) waste streams processed, (b) process chemistry, (c) discharge options and recovery of treated water, and (d) sludge disposal.

Jan 1, 1994

By G. L. Peralta

Geothermal energy is an important source of power in more than 12 countries and is a potential source in 50 countries. However, the exploration and use of geothermal resources generate residues such as scale and sludge. The scale is from the steam distribution pipes while the sludge is from cooling ponds. These solids contain significant levels of elements which are of environmental importance notably, arsenic, sulfur, copper, zinc and lead that require safe treatment and disposal. The compositions, phases, textures, morphologies and size of scale and sludge particles have been studied by laser particle size analysis, light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. In addition, their leachability was tested with protocol leaching procedures and sequential extractions. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how the scale and sludge are formed, their leaching behavior if disposed of in a landfill and in developing appropriate treatment strategies.

Jan 1, 1994

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By B. E. Penrod

The main constituents of flat glass are the eight commonest elements of the earth&apos;s crust. Five of these, silicon, sodium, calcium, magnesium and oxygen are essential. Two more, Aluminum and potassium have beneficial properties. For colorless glasses iron is undesirable, in standard clear glasses a small amount of iron is tolerable, while for most tinted glasses iron is essential. These elements are present in glass as oxides and because they are so common there is no foreseeable resource shortage. The availability of supplies of materials at particular sites at prices which enable a glass manufacturer to be competitive may be another matter. In this paper it is intended to provide a historical perspective to the current situation, to contrast some of the traditional North American and European practices, and to progressively review some of the driving forces for future change and to attempt to assess their effects upon both raw material supplier and consumer.

Jan 1, 1994

By L. Lü, M. O. Lai

"Mechanical alloying is a dry, high energy ball milling process which has been used to synthesize metallic powders in the solid state. The present study use this technique to synthesize Cu-base shape memory alloy powder from commercial Cu70Zn30, Cu86Zn14 and element AI powders. The evolution and formation of shape memory alloy powder were monitored using X-ray diffraction and microscopy. It was observed that shape memory alloy powder started to form after 1.8 ks of mechanical alloying. ? phase was clearly detected after 3.6 ks of mechanical alloying. The intensity of X-ray diffraction of the y phase increased when mechanical alloying duration was prolonged indicating an increase in the amount of y phase. Microstructure observation showed different stages of formation of alloyed powders: welding between powders and formation of layered structure, deformation and fracturing of layered structure, and finally the formation of alloyed powders.IntroductionMechanical alloying (MA) is a process used for producing powders with controlled and extremely fine microstructure. It was original developed in 1966 (1) to produce aNi-based superalloy combining oxide dispersion strengthening with gamma prime precipitation hardening. In recent years this technique has been used in producing a wide range of materials including intermetallic compounds (2, 3), amorphous materials (4-6) and other materials (7-9). In MA, a blend of powders is subjected to highly energetic compressive collision. The powder panicles are welded and fractured during ball milling. Therefore, it is essential that at least one of powders should be ductile to act as combiner. It has however been found that brittle components without soft element can also be mechanically alloyed (10), even ceramic powders (11).The present work aims to study the mechanism of formation of shape memory alloy powder during MA."

Jan 1, 1994

By Robert S. Hedin

Passive methods of treating mine water use chemical and biological processes that decrease metal concentrations and neutralize acidity. Compared with conventional chemical treatment, passive methods generally require more land area, but use less costly reagents and require less operational attention and maintenance. Currently, three types of passive technologies exist: aerobic wetlands, organic substrate wetlands, and anoxic limestone drains. Aerobic wetlands promote mixed oxidation and hydrolysis reactions, and are most effective when the raw mine water is net alkaline. Organic substrate wetlands promote anaerobic bacterial activity that results in the precipitation of metal sulfides and the generation of bicarbonate alkalinity. Anoxic limestone drains generate bicarbonate alkalinity and can be useful for the pretreatment of mine water before it flows into a wetland. Rates of metal and acidity removal for passive systems have been developed empirically by the U.S. Bureau of Mines. Aerobic wetlands remove Fe and Mn from alkaline water at rates of 10-20 and 0.5- 1.0 g. m-2? d-1, respectively. Wetlands with a composted organic substrate remove acidity from mine water at rates of 3-9 g. m-2? d-1?. A model for the design and sizing of passive treatment systems is presented in this report.

Jan 1, 1994

By G. Ferrara

The paper describes the new design criteria and control strategies for multi-density dense medium separation (DMS) circuits. The role of the multi-density separation is discussed, and it is emphasized that for many processing problems -related to minerals and coals -it may be very important to perform two or more cuts at different densities in order to obtain a remarkable improvement in quality of products, process efficiency and economy. The two-density separation by dense medium cyclones was generally performed using two dense medium plants in sequence. In contrast to the former technology, the multi-density separation can now be performed by using a single medium circuit composed of different interconnected medium sumps. The sumps, one for each density, are fed with different medium streams selected according to their density, size composition and content in non-magnetic contaminant in such a way that the rheological properties of the media are optimized. This new technology is based on dynamic systems to density the medium, on the size-density segregation of the medium in the cyclones and separating devices and on accurate control systems for the density, viscosity and stability of the dense media of the different sumps. The present paper reports on the theoretical basis for the new, advanced medium circuits and on the systems for the control of the densities and of the rheological properties of the dense media. A typical circuit for a two-density separation is also described, and some industrial applications reported and discussed.

Jan 1, 1994