Search Documents

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for over three years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1996

By Cyro Takano

An alternative use for recycling of waste from bag house of iron ore sinter plant was tested by producing and evaluating" at laboratory scale, the self reducing cold bonded pellets. This waste was characterized and the self-reducing pellets were produced using anthracite coal fines as reductant and Portland cement or hydrated lime/Blast Furnace slag as binder. It was used the molar ratio of Fe2O3/C (fix) equal to 3. Evolution of cold strength with curing time, for different contents of binder, was evaluated. Cold strength of 200N/pellet was obtained, for sinter dust, after 10 days of curing. Suitable hot strength was also presented and no decrepitation and swelling were observed. Good fractional reduction was obtained at 950°C and 1137°C. These results show that this material may be used by the Self-Reducing Processes for hot metal production, as an alternative route for this dust destination.

Jan 1, 1996

By A. Mikula, S. Karlhuber

"Unique physical and mechanical properties made the Pb-Sn solders attractive for low temperature joining of electronic parts. But since lead in solder materials has become a great enviromental problem and health concern, lead will be slowly replaced by other materials in soft solders. Some of these materials which are currently under investigation are ternary tin alloys. Many different physical properties like wetting behavior, electrical and thermal conductivity and surface tension are measured on these alloys, but on the thennodynamic properties and the phase diagram of the alloys under discussion there is only little information available. We investigated the (Ag, Au, Cu)-Sn-Zn systems and determined the thermodynamic properties over the whole composition range by emf-measurements. From these measurements we also got some information on the liquidus. In the Sn-rich corner the phase diagrams are still under investigation.IntroductionSoldering is technically defined as the joining of two base materials, mostly metals or metal coated nonmetallic substrates, with a third metal. The melting temperature of the third metal or metal alloy should be well below those of the substrates. Solder alloys can be categorized in soft and hard solders. Soft solder alloys usually contain lead, tin, bismuth, indium or cadmium and hard solders gold, zinc, aluminium or silicon. The difference between soft and hard solders is the melting temperature of the soldering material. This temperature is around 350°C.An interesting brief history of solders is given by Vianco and Frear [1]. They report, that in 4000 B.C. solders were already used in Mesopotamia. From archaeoligical evidence those solders were gold-based hard solders.Tin-lead soft solders and their use are not easily found, because in course of time tin has been reduced to stannic acid, making the identification quite difficult. Well preserved soft solder artifacts were discovered in King Tut's tomb dating from 1350 B.C. In ancient time Pb-Sn solders were used primarily for the manufacture and repair of cooking utensils and metal tools. The Romans used lead-tin solders extensively in the construction of the aqueducts."

Jan 1, 1996

By P. C. Kapur

For mineral processing spirals, mathematical force equilibrium models are sought to extend the spiral performance envelop. In Part 1 of this report, a complete geometric description of the helical spiral and its trough or channel contour is provided. The secondary circulatory fluid motion in the transverse direction that develops when water flows down a tightly turning curvilinear path and its implications for gravity separation are discussed. Different forces that act on the particle during its passage through the spiral are enumerated and quantified for a better appreciation of their relative contributions and roles in the separation process. Three force equilibrium models from the hydrology literature on sed iment transport are employed to simulate a typical spiral. While the results are promising in that the models mimic the broad performance characteristics of the spiral, what is needed is a more general spiral model taking explicit cognizance of the missing components essential to the spiral description. These are such components as centrifugal force and the steep tangential slope of the channel deck. Results of this latter exercise are deferred to Part 2.

Jan 1, 1996

By H. Yin, T. Emi

"Advantages of gas/flux injection technology as materialized in the main stay unit processes for steelmaking are depicted covering hot metal pretreatment through secondary refining. Current status of micro-kinetic issues involved in the injection technology are reviewed including gas-in- metal, gas-in-slag, flux-in-metal, metal-in-flux and three-phase dispersion systems with reference to macro-kinetics. Key problems are briefly addressed to further develop injection technology for steelmaking processes.1. FROM PAST TO PRESENTApplication of gas injection to steel industry started in early 1950's when inert gas bubbling via stopper rod, lance, or porous refractory plug was practiced to make the temperature of steel melt in ladle uniform The gas bubbling in ladle was then extended to slightly removing hydrogen ti'om the steel melt tapped from Electric Arc Furnace (EAF) and Basic Open Hearth Furnace (BOH) when vacuum processing facilities were not popular. Later, oxygen gas injection via calorized steel pipe into molten steel bath in BOH Furnace was also put into operation to promote the decarburization to increase the productivity of the process. This line of development has been made in parallel with more profound processes, i.e, top blowing Basic Oxygen Furnace (BOF) for primary steelmaking and side blowing Argon Oxygen Oecarburization (AOD) vessel for decarburizing stainless steels.On the other hand, injection of fluxes into steel bath was first industrialized in Germany in 1960's, Primary objective was to desulfurize steel melt in ladle by injecting CaC2 or CaCrCaO mixture via lance under neutral slag cover with good success. Difficulties in injecting fluxes without clogging and rippling at a desired flux/gas ratio, and durability of injection lance were resolved in due time to bring forth many injection facilities to flourish for versatile refining operation. Top injection of fluxes from main oxygen lance to BOF was also industrialized as LDAC to promote early slag formation. A new process then emerged which injects oxygen gas and fluxes together through concentric annular tuyere, installed at the bottom of the BOE into steel melt. This process, developed in Germany [Oxygen Bottom Maxhutte (OBM)] and brought into maturity in USA (Q-BOP) and Japan in a large scale operation, became the predecessor of the combined blowing (top and bottom blown) BOF which dominates modern steelmaking."

Jan 1, 1996

By Ian Baker, Xavier Pierron

"Iron aluminides hold great promise for intermediate temperature applications (to ~ 600°C) because of their excellent oxidation and sulphidation resistance and good strength. However, they have poor low temperature ductility, a feature which is exacerbated by water-containing environments. This paper presents an overview of the effects of environment on the ductility of iron aluminides, including the effects of iron aluminum ratio; ternary alloying additions, particularly boron; strain rate; and temperature. The mechanisms involved in water-induced embrittlement are discussed.IntroductionOver the last few years, it has became increasingly evident that the ductility and fracture toughness of many intermetallic compounds, particularly aluminides, are reduced dramatically if they are mechanically tested in either air or in hydrogen-containing atmospheres (1-5). For FeAI and Fe3AI, it has been shown that water vapor, for example in air at room temperature, can form atomic hydrogen by reacting with the Al atoms (1, 2). As a result in iron aluminides, the environmental embrittlement process is quite similar to traditional hydrogen embrittlement. This can be easily demonstrated by either testing an iron aluminide in an environment free of the deleterious species or by testing at high strain rates, both of which result in greater ductility. The purpose of this paper is to review recent progress in understanding environmental embrittlement in FeAI and Fe3AI, and to consider possible environmental embrittlement mechanisms. Greater understanding of this phenomenon will lead ultimately to remedies to this problem which is a major reason for preventing the practical application of these materials. First, some background on the iron-rich aluminides."

Jan 1, 1996

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

By Donald E. Wakefeld

"The pace at which mining will occur in Northern regions and Arctic lands will depend on the answers to a number of questions. Who are the local aboriginal participants? What land uses are they pursuing? What are their objectives? What is their understanding of the process of mining development? This paper will focus on the last question, communicating the process of mineral development to local aboriginal communities.IntroductionIn the environmental impact hearings for the BHP-DiaMet diamond mine, the smaller Dene Treaty 8 Nation argued for the settlement of its Land Claims as a pre-condition to development. However, the larger Dene Treaty 11 Nation were prepared to permit the mine to proceed on the basis that their people would receive benefits during the construction and operation of the mine.Wherever mining is the significant basis for tax revenues and economic development expectations may be encouraged beyond the realities of the situation. Izok Lake has been known for several decades as a significant mineral deposit but because of its size and the transportation costs involved, it is now a “frozen” ore body. The extent of its mineralization at current metal prices will not support the mining and processing costs without substantial government support for infrastructure and roads. At the opposite side of Canada, Voisey’s Bay clearly satisfies all technical criteria but, nonetheless, two Inuit groups, the Innu, and Métis, have all made LandClaims relating to the mine area.Contrasting the mineral deposits at Voisey’s Bay and Izok Lake emphasizes that the timing of production is dependent on factors such as the grade and amount of reserves, their market price, location and availability of government support. Nonetheless, it is this author’s thesis that given an economic orebody the next most important factor is good communications. It is his view that Arctic mineral development will occur quickly only where good communication has resulted in the trust and mutual respect necessary to implement the mammoth cultural changes required."

Jan 1, 1996

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By Jr. Schnakenberg

In 1986 the U. S. Bureau of Mines (USBM) embarked on a major research effort to develop technology that can substantially reduce worker exposure to face hazards simply by relocating the equipment operators to an area of relative safety. This reduced exposure mining system (REMS) research effort enhances the USBM ongoing health and safety research efforts to reduce and control dust and noise and to reduce accidents through training and better mining practices. This paper reports progress of the research that is developing and will demonstrate the technologies required for the computer-assisted tele-remote operation of continuous mining machines, haulage systems, and roof bolting machines.

Jan 1, 1996

By Suswnu Makino

Sumitomo Metal Mining developed a new nickel refining process ( Matte Chlorine Leach Electrowinning process) based on chlorine leach and electrowinning technologies. After the pilot plant study, the commercial plant with design capacity of 24,000 tonnes per year was constructed and has been successfully operated since August, 1992. During the practice of the past three years, great deals of improvement have been achieved. Through these operations the MCLE process has been demonstrated to be one of the most superior processes in the world with nickel recovery, productivity, cathode quality and working environment. Today the refinery product capacity is increased to 30,000 tonnes per year. This paper describes the equipments and operation of the Sumitomo MCLE process.

Jan 1, 1996

Copper cathode and Uranium Oxide production at WMC (Olympic Dam Corporation) Pty. Ltd. involves processing leach liquors through a copper solvent extraction plant followed by a uranium solvent extraction plant. This paper discusses the processing problems, metallurgical testwork and circuit changes made due to contamination of amine in the oxime circuit and vice versa.

Jan 1, 1996

By S. Veeramasuneni

The sign of the surface charge for alkali halides in their saturated brines has been established from non equilibrium electrophoresis measurements and on this basis the flotation response of alkali halides was explained based on the adsorption of oppositely charged collector colloids by heterocoagulation. These surface charge results for alkali halides are generally as expected from simplified lattice ion hydration theory with some exceptions, specifically LiF, KCI, NaCl, KBr, RbBr, KI, and Rbl .The presence of natural oxygen defect states in the crystal lattice and the inaccuracies involved in the gaseous ion hydration free energy values used appear, in past, to be responsible for these deviations. The presence of natural oxygen defect states in KCI, KBr, RbBr, and Rbl as characterized by UV Nis absorption, was found to account for their anomalous surface charge. Further, other positively charged alkali halides, LiF, NaCl and KI, were found to be free of oxygen defect states. Nevertheless, oxygen defects can be created in these alkali halides to make them negatively charged and has been demonstrated for NaCl. Such negatively charged NaCl can be readily floated with positively charged amine collector colloids thus confirming the surface charge/collector colloid adsorption theory.

Jan 1, 1996

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By Matthew C. Binsfield

The simultaneous electro winning of zinc and manganese from waste water treatment plant sludge was studied as a part of the overall research program, which was conducted to develop the methods for removal of environmentally hazardous metals from the Bunker Hill Superfund Site. This paper discusses the electrolytic method for recovery of zinc and manganese from the solution produced by leaching of sludge with S02 + H2S04. After three stage purification of the leaching solution, zinc and manganese were electro won simultaneously in an undivided electrolytic cell. Zinc was deposited on an aluminum cathode, while manganese was simultaneously produced (as Mn02) on a lead silver anode. The electrowinning parameters studied were the effects of: temperature, current density, electrode material, spacing of electrodes, composition of electrolyte, and electrolyte additives. Anodic and cathodic efficiencies were 30 and 91%, respectively. In light of the process design parameters discussed in the paper, which are affecting the electrowinning, these efficiencies were found as acceptable with regard to the quality and marketability of the products.

Jan 1, 1996

By Vaughan R. Voller

In many high temperature processes involving liquid melts the common practice is to solidify a fraction of the melt adjacent to the containment wall; a practice that can provide protection of the structural components of the process. The position, shape and transient behavior of these so called "skulls" and/or "ledges" are directly dependent on the thermal process conditions. This paper presents a model of a generic ledge process that can predict the steady shape of a ledge. Two numerical implementations are presented and compared: (1) based on a space grid of continuously deforming finite elements (2) based on a conjugate grid of fixed control volumes and deforming boundary elements.

Jan 1, 1996