Search Documents

CONSTRUCTED WETLANDS (CWs) ?Human-Constructed ?Built Specifically to Remove Contaminants ?Can Treat a Wide Variety of Wastewaters Including Stormwater(SW) ?Three Major Kinds ?Pond Wetlands ?Free Water Surface Wetlands (FWS) ?Sub-Surface Flow Wetlands (SSF) ?HSSF & VSSF

May 1, 2009

A series of fault slip seismic events have occurred at Garson mine. The events have occurred during development advancement exposing faults, after the extraction of single stopes due to mining induced stress change, and due to time effects after delays of many days during which no mining had been conducted. This paper discusses the study completed consisting of a global or holistic approach aimed at mitigating some of the risks associated with the structurally controlled rockbursts at Garson. Background Garson mine is located in the south east area of the Sudbury Basin (Ontario, Canada). Mining occurs in two main ore bodies (the #1 Shear and the #4 Shear) which are copper-nickel-sulphide and occur within shear zones that (as well as the ore bodies) strike approximately east-west and dip steeply south. From the north (footwall), lithologies progress (Figure 1a) from norite (NR), to greenstone (GS), and finally to meta-sediment (MTSD). A generally WNW-ESE striking, bifurcated sub-vertical dyke of olivine diabase (OLDI) cuts the series. The current active mining block at Garson is between 4700L and 5100L (levels denote depth in feet below surface).

May 1, 2009

By Bétournay. M. C.

Advantages ?Safety ?Health ?Rapid, continuous development, productivity ?Stope dilution reduction Disadvantages ?High cost and long time for equipment development ?Hard rock mining condition limitations ?Size of equipment ?Equipment set-up time, down time ?Performance does not meet financial return targets ?Drill and blast retains advantage in cost, productivity, capital investment, application flexibility ?Stress accumulation issues in deep mining, ground support and material handling issues in weaker rock

May 1, 2009

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By Ronald D. Boyer

"Early in the design stage of Meadowlands Xanadu, the client’s project director informed me that “after construction, nobody is going to come to Xanadu to see the foundations.” My response was, “Well, that’s good, because the only reason someone would come to see the foundations is if there is a problem with them.” The client’s real message was clear: the money for the project would be better spent on architectural design components and interior finishes that would attract high-end tenants and entertainment seekers. The foundations, however, were challenging. The sheer size of the Xanadu development, the varying depths to rock, the loading conditions associated with the different structures, and the construction sequencing required the use of multiple deep foundation types and specialty foundation contractors. Xanadu, when completed, will consist of over 2.5 million sq ft of entertainment venues, restaurants and retail stores; America’s first i n d o o r s n o w dome; North America’s tallest (287 ft high) Ferris wheel; and four parking decks. Finished grades for Xanadu were essentially within about 1 to 2 ft of existing grades at the site, except for a 5 acre wetlands area, which received about 8 ft of new fill. Before the current construction, the approximate 75-acre Xanadu site was occupied by the Continental Airlines (now Izod) Arena, on-grade parking lots and the wetlands area. The Arena property is part of the New Jersey Sports and Exposition Authority (NJSEA) Meadowlands Sports Complex, which also includes Giants Stadium and the Racetrack, and is located in East Rutherford, N. J. Subsurface ConditionsThe site subsurface conditions include fill materials underlain by organic silt and peat (former marsh deposits or “meadowmat”), varved clay, glacial till and shale bedrock. The Xanadu site had been a marsh until the Sports Complex was created by filling in the early 1970s. The fill consists of dredged materials from Lower New York Harbor imported by hydraulic pipeline from the Hudson River. The fill also includes “historic fill,” defined as nonindigenous material deposited to raise the topographic elevation of a site, such as construction debris and other nonhazardous solid waste, and was generally encountered in thicknesses ranging from 8 ft to 18 ft. Within the previously developed portion of the site, a layer of marsh deposits consisting of peat and organic silt was encountered beneath the fill in thicknesses ranging from two ft to seven ft. Within the existing wetlands area, the marsh deposits were up to 10 ft below existing grade. The varved clay stratum was six ft to 36 ft thick. The depth to shale rock increases from approximately 15 ft near the west side of the site to approximately 80 ft near the south side. Groundwater was tidally influenced and varied from about 6 to 12 feet below both existing and proposed grade."

Jan 1, 2009

By Robert H. Peters

This report presents a literature review conducted by the U.S. Bureau of Mines. The review summarizes what has been learned from recent empirical studies of the relationship between mine safety and characteristics of miners, mine management, and mining companies. The review is based on literature published in the United States during the period from 1976 to 1988. In addition to summarizing the empirical findings, this report discusses the implications and limitations of these studies, and gives recommendations for improving mine safety. An annotated bibliography section appears in the appendix.

Jan 1, 2009

By Viviane Tavares

The technology advance of mobile devices makes consumers of these equipment do more constant exchanges, with this the obsolete devices discarding becomes an environmental problem, due its landfill accumulation. In order to minimize the environmental impacts caused by these equipment there?s the recycling necessity of polymers, ceramic and metallic materials. The main goal of this recycling is to study the printed circuit board of device mobile processing through ore treatment in order to recoup copper. Initially printed circuit boards were processed in a knives mill, in order to liberate the ferrous material, after that it was done the magnetic separation of the reduced residue. With the not magnetic fraction it was done the grain sized analysis and sulfuric acid and hydrogen peroxide leaching analysis. With the chemical analysis results proceeding from the leaching aliquot it was possible to observe that the leaching method with sulfuric acid and hydrogen peroxide presented greater copper recovery.

Jan 1, 2009

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

By D R. Venkatesulu, N K. Nanda

Due to increased production of steel in India, the thrust is now on iron ore producers not only to enhance productivity from existing mines, but to look also into alternative resources, like lean grade iron ores such as banded haematite quartz (BHQ)/banded haematite jasper (BHJ), which are available in abundance but not yet utilised for want of suitable process technology. In this context, BHJ ore from the Bellary-Hospet sector was collected and subjected to detailed physical, chemical and mineralogical characterisation and beneficiation studies. The as-received sample was found to occur physically as alternating layers of haematite and jasper. The chemical analysis of the sample was 41.20 per cent Fe, 39.10 per cent SiO2 and 0.86 per cent Al2O3. Based on the mineralogical observation, haematite was found to be the lone ore mineral and jasper was the major gangue mineral. The microscopic observations revealed that the ore minerals liberate at a top size of 0.150 mm. Guided by the characterisation results, indicative tests were conducted using gravity and magnetic separation equipment, namely, Floatex«, gravity slime table and wet high intensity magnetic separator (WHIMS). The results indicate that it is possible to upgrade the sample by both gravity and magnetic separation techniques. However, the WHIMS results indicate that jasper grains report to the concentrate at higher gauss intensities. Therefore, based on the encouraging gravity separation results and the availability of new design spirals for treating fine particles, the applicability of gravity spirals for beneficiating BHJ in the liberation size range of -0.150 mm was studied. The sample was ground to a top size of 0.150 mm and was subjected to preconcentration using wash waterless spirals. Tests were conducted at different feed rates, pulp densities and splitter positions. The results indicate that it is possible to upgrade the sample from a feed grade of 41.20 per cent Fe to a preconcentrate ranging from 46 per cent to 62 per cent Fe with a yield ranging from 19 per cent to 55 per cent. The obtained preconcentrate was then subjected to a cleaning stage by using a combination of wash water and wash waterless spirals. The test results indicate that it is possible to obtain a final concentrate assaying 65.75 per cent Fe and 4.75 per cent SiO2 with a yield of 25.9 per cent and an iron recovery of 41.31 per cent. It was concluded that further test work is necessary to increase the recovery and improve the product specification.

Jan 1, 2009

By Zhigang Liang

A carbon free precast block was prepared by using high-alumina fused corundum as aggregate and fused magnesia, and ultra-fine Al2O3 and ultra-fine SiO2 powders as matrix materials. A small linear expansion for the precast block was achieved through spinel formation from the reaction of MgO with Al2O3. The precast block showed a lower apparent porosity, higher hot modulus of rupture and better slag corrosion resistance compared to the traditional Al2O3-MgO-C brick. Moreover, the practical application of the precast block to the ladle lining proved it to possess a better thermal insulation which could effectively prevent the temperature drop of molten steel during the refining process. It can be predicted that the carbon free precast block could possibly be accepted as a new type of ladle lining material for the production of low-carbon and ultra-low-carbon steel.

Jan 1, 2009

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By Isaac A. Zlochower

This paper presents data on the limiting (minimum) oxygen concentration (LOC), in the presence of added N2, of methane (CH4), propane (C3H8), ethylene (C2H4), carbon monoxide (CO), and hydrogen (H2), and some of their binary mixtures. It also addresses the issue of the flammable concentration (flammability) limits of these pure gases in air. The study is based on spark ignited explosions in large, spherical laboratory vessels (120-L and 20-L) using a 7% pressure-rise criterion for explosion propagation. The results of the study are compared with the older values which used long flammability tubes with a diameter >5 cm together with visual evidence of substantial upward propagation. They are also compared to results reported recently using a 12-L spherical flask with a visual flame propagation criterion. Finally, they are compared to results reported in Europe using more modest flammability criteria and smaller chambers. The findings reported here show excellent agreement between the 120-L and 12-L results, good agreement with the 20-L results, and reasonable agreement with the earlier flammability tube values for the lower flammability limits. They disagree, however, with the more conservative European values. These results and those from the 12-L experiments also feature lower LOCs than are given by traditional flammability tubes. A model for the LOCs of such fuel mixtures based on the Le Chatelier mixture rule for lower flammable limits is seen to reasonably fit the observed results on binary mixtures and can accommodate more complex mixtures as well. One such set of ternary mixtures containing CH4 and 1:1 CO:H2 is well fitted by the model.

Jan 1, 2009

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

Safety is the No. 1 concern of any drill contractor or mine operator. Everyone in the industry knows a safe site helps stabilize operational costs and enables higher productivity. When it comes to exploration drilling, research has proven a majority of injuries are caused by the mishandling of coring rods. A driller helper will typically handle up to 50 rods per shift or up to 15,000 rods per year. With an annual 340 t (750,000 lb) in rods managed by hand, the risk of serious injury is extremely high. Because of this, the top request from the exploration industry is diamond rod handling. The Boart Longyear 4200 surface exploration drill, slated for release in 2009, will give the industry a hand-free, operationally safe rig.. Developed through the collaboration of its global drilling services and products divisions and targeted at the 1,200-m (3,900-ft) NQ market, the upcoming Boart Longyear 4200 surface exploration drill features the safest and most flexible rod management sys-tem in its class. The rig includes the industry?s first, truly hands-free rod handling system. This increases operator safety on the jobsite. In addition to the rod handler, the rig also features many new innovations that boost productivity and rig efficiency while minimizing the risk of downtime due to component failure or operator error. Boart Longyear has also included an intelligent PC-based operating system designed to allow complete drilling control as well as diagnostics reporting for the rig.

Jan 1, 2009

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009

By Zhao-cheng Liu

Iron oxide red pigment powders of high quality were synthesized from pyrite cinders. Iron ox-ide red pigment powders were synthesized by hydrothermal method from the precursor of Fe(OH)3 and Fe(OH)2 colloid, which were obtained after ammonia solution reacted with acidic leaching solution produced by the reaction of pyrite cinders with sulfuric acid. Effects of reaction concentration, reaction temperature, reaction time, pH value and n(Fe2+)/n(Fe3+) on main properties of oxide iron red were studied by experiments. The prepared particles were characterized by means of X-ray diffraction (XRD) and scanning electron microscope(SEM). The results revealed that the synthesized iron oxide red particles were _-Fe2O3 and pseudocubic with particle size of 0.50~0.75µm. Furthermore, the quality of iron oxide red pigment powders reached the first grade of national standard (GB1863-89 ).

Jan 1, 2009

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009