Search Documents

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Kinross Paracatu, Victor Morais, Luis Marinho, Rolando Fuentes, Lucas Steffen, Leopoldo Muñoz, Washington Vilas

Nowadays, mining operations close to communities face increasingly challenges, especially in their drilling and blasting operations. One of the critical effects are the ground vibrations produced in its surroundings. The impact on the community must be minimized to guarantee the license to operate and, on the other hand, costs must be optimized, and an adequate fragmentation must be achieved to ensure the efficiency of subsequent processes and, consequently, to give sustainability to the business. In this regard, it is necessary that some controlled blasting technique to be performed and the utilization of advanced vibrations models. Currently, it is common in the industry either use of the double decking technique, where very low explosive charges are applied, making it necessary to use smaller drill patterns in order to keep powder factor as per design, which strongly increases the demand for drilling and a consequent impact negative on costs.

Feb 6, 2023

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By J. Mikhael Erekson, Connie Campbell Brashear, Brent Meins

Christmas morning 2020, an IED in an RV was detonated along an evacuated section of downtown Nashville, Tennessee. The blast damaged over 40 buildings, including AT&T’s Main Central Office and caused internet and cell outages across 1,200 zip codes for three days including the airport and EMS services. Published investigations by the ATF and FBI were inconclusive in determining the explosive composition and size. Video captured a large fireball that may indicate a fuel-air-mixture explosion which would create lower peak pressures than high explosives, but longer pressure duration and significant impulsive loading. Blast pressures were amplified by reflections in the urban environment bordered by the 8-story AT&T building and a row of multi-story historic buildings. Some structures had little damage as they were shielded from the blast pressure by closer buildings, and seemingly far-field structures contained damage from the pressure wave after multiple reflections and propagation through porous parking garages. Damage to the reinforced concrete frame AT&T building included snapped masonry ties, cracking and spall to the closest column, and vertical displacement of the elevator, even with the brakes applied. The historic structures directly across the street from the blast partially collapsed. Initial damage included complete failures of unreinforced masonry façades, broken timber beams, and uplifted roofs. Secondary, progressive collapse took place over months as the brick walls and weakened historic mortar could not resist typical wind and environment loads. One of the close historic structures was renovated in the 1990’s and structural retrofits to comply with building codes were required. The addition of steel columns and façade tie-ins improved survivability and it remained standing with a high percentage of the front brick intact. Generally, the observed blast damage was related to a structural component’s mass and flexibility. Internal timber framing was unscathed, but many steel studs required replacement. Glazing damage was observed several blocks away and many roof membranes were punctured by falling debris. Secondary damage from broken sprinkler lines and loss of environmental control often led to more costly repairs than the initial blast pressure damage. The proliferation of bomb-making knowledge leads to hundreds of bombings each year in the US. Building risk considerations should include explosive threats along with other hazards. ASCE structural standards and design manuals have been published to address these risks and may be useful guides for building construction.

Feb 6, 2023

By C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

FDM (Fracture Density Model) is a three-dimensional mechanistic model of blast induced rock fragmentation. FDM uses several computational mechanics algorithms to simulate the effect of blasting in different rock types. Earlier, FDM was successfully exercised to simulate 29 small scale shots from the United States Bureau of Mines (USBM), and 6 full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. Excellent agreement was obtained for those shots, and the results were documented in earlier publications. One of the drawbacks of previous ver- sions of FDM was its inability to predict the fines, specifically in Bararp quarry simulations. Ac- curate predictions of fines can be very useful in reducing energy consumptions during down- stream comminution processes and improve the mine-mill operation efficiencies. In this paper, we propose a newer algorithm that can predict the fines as well as the coarse fragments in Bararp with reasonable accuracy. The model was also applied to an open-pit Copper mine with heavily jointed rocks, and it produced very good fragmentation predictions for the full range of fragment sizes. Comparisons with the sieved fragmentation data (for both Bararp stone quarry and the open- pit Copper mines) show great potential for this updated version of FDM in modeling the entire range of fragment size distributions in mining and quarrying applications.

Feb 6, 2023

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By A. M. Venter, C. W. Siyasiya, N. K. K. Arthur, M. G. Willemse, D. Marais

Although additive manufacturing is fast gaining traction in the industrial world as a reputable manufacturing technique to complement traditional mechanical machining, it still has problems such as porosity and residual stresses in components that give rise to cracking, distortion, and delamination, which are important issues to resolve in structural load-bearing applications. This research project focused on the characterization of the evolution of residual stresses in Ti-6Al-4V extra-low interstitial (ELI) additive-manufactured test samples. Four square thin-walled tubular samples were deposited on the same baseplate, using the direct energy deposition laser printing process, to different build heights. The residual stresses were analysed in the as-printed condition by the neutron diffraction technique and correlated to qualitative predictions obtained using the ANSYS software suite. Good qualitative agreement between the stress measurements and predictions were observed. Both approaches revealed the existence of large tensile stresses along the laser track direction at the sections that were built last, i.e., centre of the top layers of the samples. This in addition leads to large tensile stresses at the outer edges (corners) which would have the effect of separating the samples from the baseplate should the stresses exceed the yield strength of the material. Such extreme conditions did not occur in this study, but the stresses did lead to significant distortion of the baseplate. In general, the microstructures and spatial elemental mapping revealed a strong correlation between the macro-segregation of elemental V and the distribution of the β-phase in the printed parts.

Feb 6, 2023

By C. Ndou, T. Mothupi, H. Mandende

The technological advances in efficient, rapid, and non-destructive hyperspectral core logging systems for systematic mineral mapping have led to the discovery and exploitation of new mineral deposits Hyperspectral imaging in the long-wave infrared range has been recently used successfully to identify various phosphatebearing minerals (monazite, xenotime, and britholite), with limited work on apatite associated with mafic-ultramafic layered intrusions. In this study we investigate the effectiveness of a hyperspectral imaging (HSI) system with long-wave infrared (LWIR) bandwidthsto identify apatite in the Upper Zone of the Bushveld Complex. The accuracy of the HSI results was validated by mineralogical and geochemical data. The two apatite-enriched zones detected by HSI suggesting widespread development of apatite throughout the uppermost 600 m of the Upper Zone. The lower apatite-enriched zone is approximately 40 m thick, while the upper apatite-enriched zone is about 23 m thick, consistent with previous thickness determinations by traditional logging and analytical methods. Spectral mixing observed in the response of apatite is ascribed either to the common association of apatite and olivine in these rocks, or to differences between the spatial resolution of the hyperspectral image and the size of apatite grains. The VNIR-SWIR wavelength region did not show prominent spectral features of apatite. Nonetheless, HSI in the LWIR range is effective in mapping apatite and should therefore be considered as an exploration tool. This research advances our knowledge of the reflectance spectroscopy of REE-bearing minerals, which makes it easier to detect, identify, and quantify REE-bearing silicate minerals by HSI.

Feb 6, 2023

By N. Wagner, P. den Hoed, J. D. Steenkamp, S. Soqinase

In pyrometallurgical processes, metal oxides are reduced from molten slag through carbothermic reduction. It is of interest to evaluate the reactivity of the carbonaceous materials towards substances such as slag. Characterization techniques such as coal petrography can provide insight into the influence of feed coal properties and how they potentially dictate reductant performance. This study aimed to compare the petrographically determined organic composition of coal to reductant reactivity. Two South African medium-rank C bituminous coals and one anthracite sample were investigated together with high-carbon ferromanganese industrial slag. The reductant reactivity tests were conducted at 1500°C in a muffle furnace to assess the potential of carbonaceous reductant in reacting with the main slag components. SEM-EDS was applied to understand the extent of MnO (and to a lesser extent, SiO2) reduction from the slag. Coal 2, consisting of a greater proportion of vitrinite (59.5 vol% on a mineral matter-free basis and 54.7 vol% including mineral matter) was the most reactive reductant. The anthracite sample, with the highest inert maceral proportions (71.8 vol% including mineral matter and 76.8 vol% on a mineral matter-free basis), was the least reactive reductant.

Feb 6, 2023

By David La Rosa, Matthew Craft, Lee Julian

Rules of thumb are ubiquitous in blasting. Typically presented as ratios, they assist with the initial assumptions of blast design and provide guidance for best practice. Examples include the blast hole diameter as a function of bench height, and stemming length as a function of hole diameter. The most common rules of thumb were developed in mid-20th century and it is important for a blaster to know if the rules of thumb are still reliable.

Feb 6, 2023

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By D. Rudenko, C. T. Aimone-Martin, J. K. Ratliff, I. G. Wong, J. Aiken, R. E. Burnham, T. A. Davidsavor

A small quarry blast was conducted with a maximum of 90 pounds per delay and shortly afterwards, area residents sensed ground motion and building shaking indicative of an earthquake. In addition, seismometers up to 500 miles (800 km) away recorded a magnitude 2.8 earthquake located in the area. Positioned in a seismically inactive area, southern Minnesota is not known for earthquakes. The earthquake was originally described by the USGS to be a surface blast at the quarry. Analysis showed that the earthquake occurred shortly (approximately seven seconds) after the quarry blast some distance away and well below the surface. This paper describes the evaluation of the “seismic events” including the blast, the following earthquake, initial governmental response, and provides the framework for assessing the relationship between the blast and the earthquake. The paper also discusses management of large volume claims from a complex event and presents a claims management strategy with best practices.

Feb 6, 2023

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Roland Alford

The ballistic pendulum is a well-established piece of test equipment originally developed for estimating the velocity of bullets and projectiles. When trying to understand the effects of different tamping methods on explosive performance, the ballistic pendulum is an excellent tool allowing calculation of explosive charge impulse. Most ballistic pendula for this application are limited to narrow impulse ranges as the pendulum mass determines the angle of swing; and a mass capable of being moved by a small charge would be far too small for a larger charge. This paper describes a modular design (the Alford Modular Ballistic Pendulum) which overcomes this problem.

Feb 6, 2023

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-growing push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source of rare earths found in the United States is bastnaesite, a rare-earth-bearing fluorocarbonate, mined at the Mountain Pass Mine in California. To increase production, it has been essential to optimize existing processes and create new ones to capture current reserves. This paper presents the results of a research program conducted to expand the understanding of the bastnaesite leaching system. With the help of prior knowledge and thermodynamic calculations, a novel single-stage hydrochloric acid leach system was created to optimize the extraction of rare earths from bastnaesite. Historically, this extraction has entailed the use of a two-stage leach system involving a high-temperature hydrochloric acid leach followed by a caustic crack. We ran a series of single-stage leach experiments by reacting locked-cycle flotation concentrate with hydrochloric acid to test common leaching parameters. The results of these single-stage tests showed significantly higher rare-earth recoveries than the reported recoveries of the historic two-stage caustic crack processes, all while decreasing the number and amount of reagents needed.

Feb 1, 2023

By E. J. Owen, S. Cherotich, V. T. McLemore

Breccia pipes are vertical pipe-like columns of rocks that provide conduits for fluid flow and open spaces for mineral precipitation, hence are focus areas for exploration. In the Gallinas Mountains, Lincoln County, New Mexico, there is recorded production of Cu, Pb, Ag, F, Fe, REE (as bastnäsite), and Au from 1902 to 1980, but no production reported from the breccia pipes. Previous studies described the occurrence of REE in breccia pipes, but their transportation and deposition controls are still unclear. The aim of this research is to characterize the magmatic-hydrothermal breccia pipes in order to understand the geochemical and physical conditions of deposition of REE and gold in the breccia pipes found in the Gallinas Mountains. There are more than 20 exposed breccia pipes that form a NE-trending belt about 3–5 kilometers, mostly gray-brown and consist of angular- to sub-rounded rock fragments, some host high concentrations of REE (80,500 ppm total REE) and Au (175 ppb). Preliminary studies suggest they are magmatic and intruded into the host rock and, subsequently, hydrothermal fluids precipitated F-REE and Au along the edges of some breccia pipes. More studies are underway to test this hypothesis.

Feb 1, 2023