Search Documents

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By Caisa Samuelsson, Taishi Matsushita, Hannes Holmgren, Sina Mostaghel

"Rönnskär Smelter of Boliden Mineral AB, Sweden, is a large end-processor of secondary raw materials and waste, including electronic scrap. Electronic scrap may introduce various impurities to the smelter's flow-sheet, among which alumina is a common and significant one. This article summarizes the results of an ongoing research at Luleä University of Technology, Sweden, to study the influences of alumina on different properties of slag from the zinc fuming process at Rönnskär smelter. A combination of different experimental techniques and thermodynamic calculations have been used to investigate properties such as density, surface tension, effective thermal diffusivity, viscosity, and melting/leaching behaviors. Results show that the addition of alumina to this slag increases the degree of polymerization of the melt, and physical properties vary correspondingly. Mineralogy of the semi-rapidly solidified samples is also changed due to alumina addition. A correlation between mineralogy and leaching behavior can be observed.IntroductionBoliden's Rönnskär Smelter is a base- and precious-metals producer located in north of Sweden. Its main products are copper, zinc clinker, lead, gold, and silver. Sulphuric acid, liquid sulphuric dioxide and iron sand (granulated slag) are some of its main by-products. In order to optimize the overall outcome of the process, different refining units are integrated in the smelter's flow-sheet (Figure 1). Copper concentrates and fluxing materials (mainly silica sand) are charged to the process. The produced matte is sent to the converter and the generated slag is charged to the fuming furnace, where it is treated by reducing gases to produce zinc clinker. The converter's slag is charged to the electric furnace, while the fumed slag is tapped into the settling furnace for further cleaning, where matte, slag and speiss (residual metals) are separated. The matte from the settling furnace is also sent to the converters; its speiss is sold to external customers; and its slag is water granulated and sold as construction material, which is known as iron sand."

Jan 1, 2012

By V. E. Cogho

Optimum Coal Mine comprises numerous defunct, active, and future mining sections. The mine is primarily a large opencast coal mine; however, underground mining activities will be increasing steadily over the next five years. Opencast and underground mining activities have a significant impact on surface and groundwater resources. To ensure that the mine will be able to continue with its mining operations in the catchment, the extent of this impact requires that substantial intervention and mitigation measures need to be implemented to ensure the environmental integrity and economic use of the catchment's water resources. In developing a sustainable long-term mine water management strategy, numerous scenarios had to be analysed. The various scenarios are a combination of water and land management activities. The main components of the mine's integrated water management strategy include: ? Management of water recharge by continual and appropriate rehabilitation of disturbed land ? Beneficial re-use of impacted mine water for coal plant process water and mining operations ? Reclamation and desalination of remaining excess impacted mine water to potable standard. From the mine's long-term water balance, it is evident that the continued implementation of numerous water management actions is required to mitigate the water resources impact in a sustainable manner. In addition, the installation of a water reclamation plant at Optimum Coal Mine (15Ml/day) is a key step for the mine to achieve a zero impact target.

Jan 1, 2012

By A. Tordoir, S. S. Kanchibotla, W. Rogers, E. Engmann, B. Bisiaux, S. Ako

Blast-induced rock mass displacement can have a significant impact on ore loss and dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of, blasting can lead to significant financial losses due to ore loss and dilution. Ore dilution occurs when waste material is miscategorized as ore and sent for processing or stockpiling, diluting the run-of-mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorized as waste and sent to the waste dumps, thus never being processed and recovered. Extensive research has been conducted at the University of Queensland over the last fifteen years to understand the impact of blast movement on ore loss and dilution. Recent outcomes of this research have led to the development of innovative tools and techniques to measure and model blast movement. These techniques have been implemented at the Ahafo gold mine in Ghana to understand blast movement dynamics and to implement solutions to reduce blast-induced ore loss and dilution. These solutions are validated through controlled trials and have been incorporated into site standard operating procedures.

Jan 1, 2012

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By Peter Faust

"The south access road to San Francisco’s Golden Gate Bridge, known as Doyle Drive or Presidio Parkway, needs to be replaced. Built in 1936, it is the primary highway and transit linkage through San Francisco between counties to the north and south. The roadway is tucked into the natural contours of the Presidio and the Golden Gate National Recreation Area, one of the nation’s largest urban parks.The old steel truss structure will be replaced by a new concrete cast-in-place bridge. The foundation design of the new bridge is based on drilled mono shafts below each bridge column. Most shafts required large diameter permanent steel casing installed under strict vibration limitations since several historic landmarks are near the project alignment. Malcolm Drilling decided to use the largest oscillator in the world to install the piles.The area occupied by the Presidio is generally hilly, sloping down northwards to San Francisco Bay. In the western half of the project route, two bluffs rise steeply to about 80 ft (25 m). The bluffs are separated by a valley 60 ft (18 m) deep and 1,500 ft (457 m) wide, which is spanned by the old and new bridge. Overburden soils in this valley are made up of artificial fill, slope debris, ravine fill and Colma Formation, a fine to medium-grained sand unit with clay beds. The Bay Muds encountered in the project area are typically soft clayey silts, becoming medium stiff with depth.The basement rocks underlying the overburden belong to the Franciscan Formation, described as shale, sandstone, serpentine and greywacke, it is extremely variable in hardness, fracturing and weathering. The material can vary from very hard to very soft, can be slightly to very intensely fractured and almost not weathered, to totally decomposed within relatively short distances both laterally and vertically. Rock strength can vary from too weak to be tested to serpentine layers with unconfined compressive strength of 15,000 psi (103MPa) or higher. Groundwater levels in the area are typically no more than 10 to 20 ft (3 to 6 m) below the ground surface."

Jan 1, 2012

By A. R. Miller

A fuel cell locomotive incorporates the advantages of its competitors, namely catenary-electric and diesel-electric units, while avoiding their disadvantages. It possesses the environmental benefits, at the vehicle, of an electric locomotive but the higher overall energy efficiency and lower infrastructure costs of a diesel locomotive. The natural fuel for a fuel cell is hydrogen, which can be produced from many renewable sources or via nuclear energy, and thus a hydrogen-fuel cell locomotive will not depend on imported oil. Hydrogen produced from renewable primary energies or nuclear energy would provide a totally zero-emissions vehicle, that is, with zero carbon in the energy cycle. A project partnership among Vehicle Projects Inc of the USA, and South African partners Anglo American Platinum, Ltd, Trident South Africa, and Battery Electric, has designed and is launching a series of five prototype fuel cell-powered mine locomotives.

Jan 1, 2012

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10 ? 15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2012

By R. Degel

Submerged arc furnaces and electric smelters are applied in numerous metal and slag production lines. Particularly in ferroalloy and non-ferrous metal production, like silicon metal, platinum group metals, calcium carbide, and copper, the units are an essential part of the production technology. Most of these electric furnaces are considered to be highly energy-intensive units. The high level of required electrical power is defined by the process. SMS developed several measures to reduce the overall electrical energy consumption of these metal production lines. In particular, the following measures contributes to a lower energy consumption: improved electrical efficiency with intelligent design and application of components, minimizing the heat losses from the furnaces with a balanced cooling/refractory systems, minimization of process steps (such as elimination of agglomeration), recovery of energy, process optimization (resulting in higher metal yield) and the achievement of higher recovery rates, enlarging furnace capacity to reduce heat losses, and maximizing the power-on time. This paper gives an overview of the above-mentioned solutions.

Jan 1, 2012

By R. Gebrekristos

It is commonly accepted that three types of aquifers exist in the Bushveld Complex: (a) alluvial aquifers in areas of river courses, (b) weathered bedrock aquifer formed by the in-situ weathering of the bedrocks, (c) fractured aquifers underlying the weathered aquifers controlled by the regional and local fracturing of the crystalline rocks. Hydrogeological studies conducted in the Critical Zone of the Bushveld Complex in the western limb show that the UG2 pyroxenite layer is of a particular interest and has a unique aquifer property. It yields much of the groundwater inflow into some mines and can be classified as the most important aquifer in the vicinity of the mining zone. The UG2 pyroxenite aquifer is restricted to the dipping UG2 pyroxenite unit. The unit weathers more intensely than the surrounding norites and anorthosites and is characterized by deeper weathering horizons (two to three times deeper than the surrounding rocks). For much of the UG2 mining area between depths of 35 ? 80 m, stoping of the UG2 takes place approximately 5 ? 7 m below the UG2 pyroxenite aquifer, and usually there is no groundwater inflow into the mine workings. However, unsealed deep exploration boreholes intersecting the UG2 pyroxenite and reaching underground mine workings, or mine roofbolts penetrating the weathered pyroxenite aquifer from underneath, can result in significant groundwater inflows into the underground workings. The reason as to why the UG2 pyroxenite weathers more than the norites and anorthosites has not been fully studied but is suspected to be due to the bedding planes of the unit and mineralogical composition of the particular pyroxenes forming the unit, which result in preferential physical and chemical weathering under atmospheric conditions. The weathered pyroxenes form sand-sized, rounded grains with improved effective porosity and permeability suitable for the storage and passage of groundwater. The orientation of the pyroxenite aquifer can easily be determined as it dips with the Bushveld layered strata. No-flow boundaries can be assumed on the hanging- and footwall of the pyroxenite aquifer and the flow rates can be estimated using 2-dimentional analytical equations. However, this must be confirmed with strong conceptual models since the existence of a fracture network connecting the pyroxenite aquifer with the overlying weathered and/or underling fractured aquifers can complicate the system, lowering the accuracy of analytical models and necessitating the utilization of numerical models.

Jan 1, 2012

By L. Bloch

Most mine safety initiatives in South Africa are doomed to limited success because of one simple fact: they are a-historical and un-cultural and do not deal with the serious ?legacy issues? that still negatively impact on safety, production, and relationships. We in the SA mining industry continually use imported, foreign safety concepts and systems that will not work fully in a South African context. ?The 4th Wave: Culture-Based Behavioural Safety?, as developed by Lance Bloch, an international award-winning clinical psychologist with 12 years? experience in the mining industry - focused mostly on Platinum - is making waves. He has been very successful in creating people-centred, empowered, high-performance safety cultures wherever he has worked. Not only does the 4th Wave transform the corporate culture of a mine, improving safety and production and building an environment of Ubuntu, but it also uses people?s cultures as a means of winning hearts and minds in the battle for safe production. Powerful relationships are built through engagement at all levels, leading to all being focused on the best needs of the company and its constituents as a whole. The programmes are no less than nation-building - something most necessary in the industry, with the pressures from community, unions, the DMR, and politicians. This presentation will describe and discuss the 4th Wave as an advance on previous safety technology and programmes, as particularly relevant to platinum mining in South Africa today.

Jan 1, 2012

By C. A. Snyders

This paper investigates the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were performed on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of platinum, palladium, and gold were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours and 100 per cent, 97.4 per cent, and 99.9 per cent respectively after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while nickel concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, nickel adsorbs at approximately the same rate as that of the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and experiments suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing.

Jan 1, 2012

By E. Schoeman

Ion exchange resins were investigated for the effective recovery of platinum, palladium, and gold from a pregnant cyanide heap leach solution. Screening results indicated that strong-base anion exchange resins proved to be most effective in the recovery of these metal cyanides. Gold was selectively recovered with the use of Minix, while effective recovery of gold, platinum, and palladium over the base metals, copper, and iron, was achieved with Amberlite PWA-5. Successful elution of these metal cyanides was possible from both Minix and Amberlite PWA-5, using a 2M potassium thiocyanate solution at ambient temperature. Acidic thiourea was unable to elute platinum from either Minix or Amberlite PWA-5. Effective elution of palladium and gold were, however, achieved with use of acidic thiourea. Using these results, two conceptual flow diagrams for the recovery of these metals from cyanide solutions are proposed.

Jan 1, 2012

By B. R. Conard

Occupational epidemiology of the nickel-producing industry has found that inhalation exposures to certain nickel-containing substances are linked to respiratory cancers and to nonmalignant respiratory endpoints. Establishing such a linkage, however, is complicated by the fact that some diseases occur long after exposure to a causal agent (i.e., some diseases have long latencies). Furthermore, most chemical agents (especially nickel substances) vary significantly in their toxicological properties and their concentrations in workplace air have varied over processing history. Because of these complications, it is critical to understand historical exposures to specific nickel substances. To assist in this effort, the author focuses on the history of smelting and its related processes at Vale Canada’s (Inco’s) Ontario operations in the first half of the 20th century.

Jan 1, 2012

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

An atomic force microscopy (AFM) has been applied to study the adsorption of collectors on mineral surfaces in a copper/molybdenum flotation system. AFM images show that collectors absorb on chalcopyrite surface in patches at pH 11. A study of temperature effect on surface morphology excludes the possibility that these patches are nanobubbles forming on hydrophobized mineral surface. Hydrocarbon oil absorbs on molybdenite quickly, while KEX (potassium ethyl xanthate) has little affinity for molybdenite. Pyrite is much more reactive in water and its surface is easily coated in Ca(OH)2 solutions at pH 11. Based on the obtained AFM images, the adsorption of chemicals on mineral surface and its impact on copper/molybdenum flotation were discussed.

Jan 1, 2012

By W.A. van der Westhuizen

Mineral resource management has become a well used phrase in the mining and minerals industry. Mineral resource managers are being appointed in many mining and mining-related organisations. Every mineral resource manager has his/her own ideas regarding what MRM means. There seems to be a tendency to define MRM close to home; geology would apply MRM principles to their environment and so will metallurgy, planning, mining, survey and every discipline and participant in the mining value chain. What do we do in the MRM environment and what do we aim to achieve? Surely we must have goals: what are they? Is value tracking MRM? What about best practices? Let us start at the beginning: what do we want to achieve in any mining operation? The minerals industry would like to make money, now and in the future. This calls for serious management inputs. The most important aspect is a holistic management approach regarding the total mining value chain. Process optimisation follows with application of Mineral Resource Throughput Management (MRTM) and Process Flow Management principles. Once flow processes have been established the necessary condition driven standards and measurements will be installed to ensure continuity in applicable processes.

Jan 1, 2012