Search Documents

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By P Guj, J A. Bell

The valuation of early-stage exploration projects requires a valuer to take into account a large number of uncertain value drivers, the interplay among which may be non-linear. This paper examines some of the key value drivers including geology, target metrics, project area and maturity, the market and the psychology behind the decision-making process. The commonly accepted valuation methods and their underlying logic are outlined, including a view on why they evolved, what value drivers they attempt to address and their potential shortcomings. These methods include the multiple of exploration expenditure, geoscience rating, expected values and market based methods. The potential future valuation methods of replacement values and neural networks are also introduced along with how to minimise heuristic bias and error within the market-based approach.CITATION:Bell, J A and Guj, P, 2012. Exploration value drivers and methodologies, in Proceedings Project Evaluation 2012 , pp 17-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By B Maybee, L Fava, D Millar

In the context of a case study for an underground gold mine, the value generated by a schedule optimisation tool (SOT) is assessed. SOT is a software tool for underground mine planning that maximises the net present value (NPV) of a development and production schedule. A baseline study measures the NPV of a schedule generated by SOT from a sequence prepared by the site mine planners. Operational resource constraints and precedence constraints are adhered to by the schedule and NPV is evaluated with a financial model including revenues, costs and discount rate, as specified by the mine planner.The case study has several facets in addition to the baselining component. Scenarios were conducted that examined the degree of constraint on operational resources, the projected gold price and unit costs. Life-of-mine schedules subject to optimisation using SOT allowed for equitable comparisons.Haulage was identified as a dominant constraint for the mine. It was one of six operational resources that were used to constrain the optimisation of the mine schedule, with alternative levels for some of these constraints being identified so that their effects on the NPV could be studied. Alternative price projections for gold and different cost projections were identified and their effects on the optimised schedule examined. Price and cost scenarios that brought additional economic material into the schedule at various times in the mine life were considered in comparison to a scenario that assumed no additional economic material would become available.This case study illustrated that the use of a schedule optimisation tool to optimise mine schedules provides mine planners with an ability to perform a wide variety of analyses in a relatively short period of time. Such tools thereby support strategic decision-making that can add significant value to an orebody.The case study demonstrates that by fixing the set of development and production activities to be carried out before optimising the life-of-mine schedule, the mine planners can inadvertently set up a situation where the NPV would be progressively eroded in the last several years of the mine life. This clearly illustrates the need for schedule optimisation to be integrated with life-of-mine planning.CITATION:Fava, L, Maybee, B and Millar, D, 2012. Decision support for an underground gold mining operation - A case study using the schedule optimisation tool, in Proceedings Project Evaluation 2012 , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By A Chandra, P Guj

Only a few complex real options can be valued using closed-form equations, such as the Black and Scholes formula, because these algorithms are restrictive and prevent the construction of practical project evaluation models. Although a binomial lattice method paired with the ærisk-neutral probabilityÆ provides an easier and flexible modelling of exploration and mining projects, it has limitations when projects are complex, long-lived and influenced by the interplay of various market and private uncertainties. In order to overcome these limitations, modern decision tree software using dynamic programming capability can be used for real option valuations. This is a powerful computational tool in which the impact of various sources of uncertainties can be differentiated, so that the optimal decision path can be explicitly displayed visually. There has been significant academic controversy surrounding whether different real option (RO) valuation methods would lead to different real option values (ROV). This paper, using a realistic copper mining example, demonstrates that as long as the same degree of subjectivity and consistency are used in different real option valuation methods, they yield the same result. This conclusion is valid irrespective of whether the cash flow volatility generated by various sources of uncertainties is handled in an aggregated or in an explicit and differentiated manner. This paper compares two choices for an investor either to æbuy now and developÆ a project or to enter into a ætwo-year option to purchaseÆ after the proponents have developed it. It also shows how significantly different net after-tax operating cash flows may be generated by these different choices on the same underlying asset represented by the project. This is due to the difference in the amount and timing of the relevant capital investments affecting the depreciation and amortisation charges and as a consequence, the income tax paid. CITATION:Guj, P and Chandra, A, 2012. Real option valuation of mineral exploration/mining projects using decision trees - Differentiating market risk from private risk, in Proceedings Project Evaluation 2012 , pp 177-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By J Gould, T Elkington

Mine operation strategies are commonly optimised with a net present value (NPV) maximisation objective. There are well known properties of a typical mining project optimised for NPV, including high production rates and declining cut-off grade schedules. In practice, however, frequently there are operations that diverge from such NPV-maximising properties. Although a range of reasons for this can be at play, one possible explanation is that operators intuitively adjust their strategies to compensate for the flaws inherent to NPV maximisation. In particular, NPV analysis does not reflect the benefits of managerial flexibility inherent in a mining plan. Real options valuation (ROV) is an alternative approach that addresses this issue. We compare the properties of NPV and ROV optimisation solutions generated for the same scenario. Our simple case study demonstrates that the presence of real operating options in the optimisation model not only entails increased project value as expected, but also tends to encourage lower processing capacity (with lower associated capital cost), higher cut-off grades and greater use of stockpiles.CITATION:Elkington, T and Gould, J, 2012. Real option value optimisation, in Proceedings Project Evaluation 2012 , pp 35-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By S Shafiee, N Abbate

The evaluation of mining projects requires a methodology that will give flexibility and manage the existing uncertainty within the projects. The discount cash flow (DCF) and other traditional evaluation approaches, which are widely used in evaluating a significant number of mining projects, have simply assumed that the main variables remain constant in their evaluation; elements such as discounted rate, mine life, operating cost and production rate. The DCF ignores managementÆs flexibility to adapt and reforecast and revise decisions. Real options valuation (ROV) is one of the modern evaluation methodologies that provide a tool to adapt and revise mining projects under uncertainty and future variables movements. ROV brings more variables into the evaluation model compared to DCF and assumes them as uncertain and dependent. Finally, ROV provides a range of solutions that can assist in managing this flexibility.This paper endeavours to compare ROV and DCF for mining projects comprehensively and applies these two techniques in the model. The paper shows that ROV will be inclusive of extra value in mining projects due to variables not allowed for, or even ignored, when the DCF model alone is used. One of the significant advantages of the ROV method is being able to evaluate mining projects under different scenarios from the inception of the projects. Furthermore, ROV gives the ability to evaluate the mining project while allowing for abandonment, temporary suspension, or expanding the mining project. In other words, the ROV evaluation process creates an analytical environment, which allows for optimisation of the mining plan within the mining project, as well as the ability to change the capital structure dependant on existing circumstances over the life of the project. The ROV is a new evaluation method that can add value in mining project analysis and offers opportunities to amplify gains, or to mitigate losses. This paper also discusses some of the reluctance to use ROV instead of DCF in current project evaluation.CITATION:Shafiee, S and Abbate, N, 2012. Now, this is the time for mining companies to choose - Real option valuation or discount cash flow, in Proceedings Project Evaluation 2012 , pp 225-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G M. Jones, J Rademan

Debswana, owned by the Government of the Republic of Botswana (GRB) and De Beers in a 50:50 joint venture partnership, operates the Jwaneng diamond mine in Botswana - the most valuable diamond mine in the world. The mine provides between 60 - 70 per cent of DebswanaÆs earnings, and about 30 - 40 per cent of the GRBÆs income. In 2008, the company embarked on the Cut 8 Project - an open pit waste cut-back to expose more diamond bearing ore to sustain mine life by another six to seven years. This undertaking was much larger than previous cut-backs; it increased the waste stripping ratio threefold, increasing significantly the waste handling fleet of trucks, shovels and infrastructure, and impacted a large part of the materials handling plant which required replacement with new facilities. The project coincided with the beginning of the Global Financial Crisis (GFC) and a slowdown in the economy. Its $4 billion total life cost was billed as æthe largest private investment project in BotswanaÆ which produced heightened expectations amongst stakeholders that it would redress some of the issues brought about by the GFC and leave behind a legacy of jobs, increased opportunities for citizen owned business and improved social infrastructure.Most of the big project challenges were non-technical and ranged from dealing with various stakeholders?at?all levels, a 25 per cent currency depreciation of the Botswana Pula against the South African Rand, obtaining work permits for non-citizens in a job starved environment, managing construction to world class safety standards, managing the low productivity of construction workers and producing a viable legacy program that satisfied the GRB and stakeholders. Whilst most of these risks were identified in front end studies, the magnitudes were in many instances underestimated. Managing this uncertainty on Cut 8 can provide valuable lessons to other projects in a similar environment, or at least provide the information to indicate that these factors should be adequately provided for in the financial evaluation of a project in the form of budget, schedule, contingency or risk mitigation.CITATION:Jones, G M and J Rademan, 2012. Reliability of expert judgements and uncertainty assessments, in Proceedings Project Evaluation 2012 , pp 109-116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By T Y. Dube

In this paper current net present value (NPV) based mine valuation techniques that take into account market and private risk are discussed and analysed. Potential pitfalls that arise from the application of a portfolio, market or commodity based risk metric to a mining project are identified. An alternative non-simulative framework for quantifying and factoring market and private risk in NPV calculations is proposed and then applied to a hypothetical case study in an attempt to overcome identified pitfalls. Mathematical proof that a static discounted cash flow (DCF) calculation can underestimate or overestimate mine NPV is presented, the conditions for each are outlined and the degree of underestimation defined.CITATION:Dube, T Y, 2012. How the use of market-based risk metrics can undervalue good mining projects and overvalue poor ones, in Proceedings Project Evaluation 2012 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By D Jeffery, R Whittering, G Lane

Most aspects of process design are best addressed via bench scale or pilot plant scale test work. However, as experience is gained, fundamental or indicative data can provide more than adequate information to manage the risk associated with some process aspects of concentrator design.Historical precedence exists where minimal design test work has resulted in successful projects. On many occasions benchmarking, sometimes supported by fundamental data such as mineralogy, has been used to successfully develop effective process plant outcomes. Of course, this style of approach is most common with æfast trackÆ projects and often comes with the usual surprises that result from inadequate geometallurgy to define the project cash flow.This paper explores the risks and opportunities associated with the various facets of process development and design for a base metals concentrator. The paper is intended to provide guidance to project managers rather than address the technical aspects of process engineering.CITATION:Lane, G, Whittering, R and Jeffery, D, 2012. Benchmarking versus test work - How should you manage process risk?, in Proceedings Project Evaluation 2012 , pp 49-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By T Schrimpf, I Bryan

The life cycle of a mining project begins with initial regional exploration and ends with mine closure and rehabilitation. Between resource definition and the commencement of mine construction is the study phase. In this phase technical concepts and processes are defined, evaluated and assessed with the aim of establishing whether the deposit is economically feasible. The study phase usually involves various steps from a concept/scoping study to prefeasibility and ultimately definitive feasibility study. The complete study phase can take several years. Although the costs for studies are low in comparison to actual construction and operating costs of a mining project, they are significant especially for junior exploration and mining companies advancing projects to the point of being funded.The studies aim to determine selected parameters for the project, eg mining and processing methods, operating strategy, etc and provide a roadmap for project development ahead. Although mining studies are of the utmost importance for the mining project and the project owner, they are usually carried out using a conventional engineering approach: the consultant or design engineer works to a defined scope of work. The resulting design might be based on good engineering, but might often also fail to provide the solution for the project owner that delivers the best shareholder value. An alternative to this more traditional approach to project evaluation is what we have termed a value engineering approach. Value engineering is a creative, organised effort, which in the case of a mining study analyses the requirements of the study for the purpose of achieving the essential outcomes with the highest shareholder value. The outcome of a study is a concept that delivers the highest achievable value of the resource project and shows the way ahead to realise this value. Through a group investigation by experienced, multi-disciplinary teams the value of the resource is improved through the study of alternative options, methods and processes. The scope of the study is not limited to a narrowly defined engineering scope, but to the creation of value.The study commences with the identification of key value drivers and risks, based on the available information (drill data, geotechnical data, metallurgical test work, etc). This enables the quantification of key uncertainties, risks and value adding opportunities. Study efforts concentrate on key value drivers and are not unnecessarily spent on side issues. This approach can significantly reduce the time frame and costs for the study phase.This paper describes in more detail RMDSTEMÆs value engineering approach to mining studies and illustrates it with examples and case studies.CITATION:Schrimpf, T and Bryan, I, 2012. The application of value engineering principles to mining studies, in Proceedings Project Evaluation 2012 , pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By R Redden

"The Didipio Gold-Copper project in the Philippines has been a well-defined reasonably high gold grade porphyry for almost two decades. OceanaGold are now bringing the project into production in late 2012 and have recently reoptimised the project with the goal of combining the inherent high grades with higher through-put than previously proposed that will see strong initial metal production. The project was discovered and well defined by 1995, but has seen some obstacles to development, namely sovereign risk, capital cost and project funding. The project strengths over this time that have kept the flames alive are: strong grades large orebody with low stripping ratios a simple beneficiation process and a clean high-grade concentrate strong support from the Philippines government.The initial study in 1998 used Gold and Copper price assumptions of $325/oz and $0.95 lb respectively. Today reserves are based on $950 and $2.85. So, being a porphyry with a large reducing grade halo, the deposit now lends itself to extraction on a much larger scale than before, without any significant capital expenditure as a larger open pit now dominates the project.Didipio is a game changer for OceanaGold, so it has been important to learn from history and to capitalise on a strong initial metal production profile. The project sits in a reasonably remote mountainous area of Luzon which sees annual typhoons and numerous short duration high intensity rainfall events and two rivers flowing through the project area, so it has not been without some innovative technical solutions.CITATION:Redden, R, 2012. Didipio - Learning the lessons, adapting and getting ready for production, in Proceedings Project Evaluation 2012, pp 67-76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By K. A. Natarajan

The utility of yeast, Saccharomyces cerevisiae, in the separation of quartz from hematite is demonstrated. Yeast cells, as well as their metabolites, functioned as flotation collectors, depressants or flocculants and dispersants for hematite and quartz. Interaction between yeast and the above minerals resulted in significant surface chemical changes, rendering quartz surfaces hydrophobic and hematite hydrophilic. Mineral-specific extracellular proteins and exopolysaccharides were secreted by yeast cells when grown in the presence of quartz and hematite, respectively. Quartz could be efficiently separated from hematite through microbially induced flotation and selective flocculation.

May 1, 2012

By Hussin A. M. Ahmed

Oxidized coals are difficult to float. Therefore, in this paper, a special flotation procedure was investigated for upgrading this type of coal. The procedure is called direct contact flotation. It relies on mixing dry coal either with pure (anhydrous) flotation reagent(s) or microemulsion. By applying the new direct contact flotation procedure, a coal yield reaching > 95% using anhydrous flotation reagents was achieved, but with relatively high consumption of reagents (up to 30 g/kg). This high reagent consumption may be attributed to the fines included in the flotation feed (100% less than 0.5 mm, with 40% less than 75 µm). On the other hand, the clean coal yield was found to be approximately 88% when mixing dry oxidized coal with microemulsion droplets from dodecane and dodecyl tetra (ethylene glycol) ether (C12E4) in water at a total reagent dosage of 10 g/kg. The direct contact of coal either with unhydrous reagents or microemulsion also provided a high flotation selectivity.

May 1, 2012

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By Jennifer J. Swenson

El presente texto describe los problemas de deforestación, precios e importaciones de mercurio en la minera artesanal aurífera de Madre de Dios. En ese sentido, a medida que la interconexión de la economia mundial avanza, es más difícil que países en desarrollo aprovechen las fuerzas lucrativas de la demanda global para lograr una sostenibilidad social y ambiental. En consecuencia, los países en desarrollo contienen un peso ambiental desigual en relación con los países desarrollados qie importan materias primas. Como ejemplo de ello, el precio del oro aumentó, así como la minería aurífera informal y no industrial en los países en los países en desarrollo y el mal manejo del mercurio en el uso del oro, repercutió en el medio ambiente y los mismos mineros, al igual que el problema de la deforestación. Por ello, se plantea un programa para enfrentar dchos problemas en la región de Madre de Dios y reducir el aumento de la minería informal.

May 1, 2012

By I M. Platten, S C. Dominy

The Clogau St DavidÆs gold mine has a recorded production of around 81 000 oz Au and it is the largest mine in the Dolgellau gold-belt and BritainÆs most prolific historical producer. The original mine was first worked for copper, however; in 1854, gold was found in waste material from the St DavidÆs section. In recent times the mine has operated intermittently between 1983 - 2007. The principal black shale-hosted gold-bearing reef (Main Reef) can be traced for about 3 km, striking approximately NE-SW and dipping steeply between 60¦ - 90¦ SE. The reef system pinches and swells, changes strike and splits into a number of smaller branches. Reef width is variable, ranging from over 6 m to a few cm and in places reducing to small irregular blobs. The reef is internally complex and composed of swarms of narrow (1 - 300 mm) subparallel veins separated by country rock sheets. The gold-bearing veins within the reef package are discontinuous; though generally possess bonanza grades running 10s - 100s oz/t Au. It has historically been shown that some gold-rich vein segments can grade up to 300 oz/t Au. The predictability of the gold-rich segments is poor, but has been shown to be related to presence of the Clogau (black shale) Formation, and/or the mechanical interactions of the reef with greenstone sills, reef branching and splitting and/or cross-fractures to form ore shoots. The mine is currently being re-evaluated as a potential small-scale selective operation.CITATION:Dominy, S C and Platten, I M, 2012. Geology, mineralisation and potential of the Clogau St DavidÆs mine, Dolgellau gold-belt, Gwynedd, Wales, in Proceedings Narrow Vein Mining 2012 , pp 101-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By P. Zhang

This paper gives a review of promising technologies for phosphate processing, and covers flotation, analysis and process control, as well as tailings treatment and utilization. Air bubbles of less than a µm in size, combined with relatively large bubbles, have been demonstrated, both in the lab and on a pilot scale, to improve flotation dramatically, by reducing reagent use while improving product grade. Innovative use of polymers has allowed rapid dewatering of fine tailings with a final product that does not segregate. The first online laser-induced breakdown spectroscopy (LIBS) analyzer was created, allowing rapid analysis of wet samples using the laser technology. Many large commercial projects are successfully pursuing the utilization of phosphogypsum.

Feb 1, 2012

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012