Search Documents

By A. J. Dickson, A. M. Starfield

This paper reviews the progress made to date in the development of computer models of heat and moisture transfer from rock surfaces to the ventilating air in deep-level mines. The application of these programs to ventilation planning and design is discussed.

Jan 1, 2014

By Juan Estrada, Mirtha Frómeta, Rubén Alcalá, Emilio Montejo, José Castellanos, Juan Berto, María Rivas

"The oxidized nickel ores from San Felipe deposit are composed mainly Smectites which gives to the pulps very unfavorable rheological .properties (cinematic viscosity and high shearing strength) for transportation processes (pumping), very low settling velocities and very low thickened pulps. These properties do not allow the preparation of high % solids, which affects the economic efficiency if a high pressure acid leach (HPAL) process is used. Pulps of close to 30% solids have very high BYS making pumping impossible. CIPIMM developed three technologies to solve these problems and to substantially increase the % solids in the pulps to be leached without a thickening step. These technologies are: • CIPIMM 2. At Preparation of pulps using additives. This method is based on the effect of some additives (inorganic salts) to improve the pulp’s properties. The use of this method allows increasing the % solids in the pulp up to 40% with good rheological properties • CIPIMM 2B. Preparation of pulps by thermal treatment of the ore previous to the preparation of the pulps. This method is based on the thermal destruction of the clays structure. Its use allows to obtain pulps with 50 - 60 % solids with excellent rheological characteristics. As a collateral effect, the Ni and Co grades increases by 10 - 15%. • CIPIMM 2C. Pulp preparation by chemical treatment. This method is based on the chemical transformation of clays, to obtain without thickening, pulps with 43- 45% solids and excellent rheological properties. The use of one of the three technologies depends on the chemical and mineralogical composition of the ores and the results of technical-economical evaluations to determine which one is the best alternative before running higher scale tests."

Jan 1, 2014

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By Jiongtian Liu, Jianjun Wu, Yongzhou Wan, Li Feng

"Mechanical Thermal Expression (MTE) is a developing non-evaporative lignite dewatering technology. It has been shown to effectively dewater high moisture content in low rank coals via the application of mechanical force and thermal energy at elevated temperatures. In this paper, the dewatering behavior of Yunnan Xiaolongtang lignite during the MTE-process was studied. Furthermore, how variations in temperature and pressure during the MTE process affect the surface oxygen functional groups and pore structure were also discussed using Fourier transform infrared spectrometer (FTIR) and mercury intrusion porosimetry (MIP). Increases in MTE temperature and pressure resulted in significant reductions in residual moisture content and moisture holding capacity, along with the increase of fixed carbon content and reductions of other elements content, especially oxygen content, which have been largely attributed to the destruction of the surface oxygen functional groups and porosity in lignite. The optimized technology conditions are temperature 150~220°C and pressure 7~10MPa. The residual moisture content of the lignite treated by MTE under the conditions of 200°C and 10MPa is decreased to 8%, while the dewatering rate exceeds 76 % and the calorific value approaches 22 MJ/kg. The experimental results offer a deeper understanding of the influence of process parameters on the lignite stuctures and properties. The reduction in residual moisture content, surface oxygen functional groups and pore volume under increasingly severe MTE conditions are suggestive of the structure changes that accompany increased coalification (rank) within the lignitic range."

Jan 1, 2014

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By G. Bonifazi

Mining activities belong to human history, they are lost in the mists of time. They usually impact on large portions of the territory, both directly (exploitation areas and logistic activities directly related to exploitation) and indirectly (exploited material handling, processing and storage areas). As a result, at the end of mine life cycle, dismissed areas usually cannot be directly re-utilized without efficient and well addressed rehabilitation actions. Main goal of the proposed approach was to analyze the results obtained when a set of procedures, based on the collection and the analysis of remote sensed data, is developed to evaluate the effect of rehabilitation of land contaminated by extractive industry activities and to perform a monitoring and registration of the environmental impact of such operations by the application and the integration of modern information technologies, as Earth Observation (EO) and Geographic Information Systems (GIS). The study was developed in the framework of the EU-Asia program of the European union (EXTRACT-IT Project-Contract No: CN/ASIA IT&C/006 (89870): Application of Information Technologies for the sustainable management of Extractive industry activities) and it was addressed to three different dismissed mine areas in India, Thailand and China, respectively. The results, in terms of methodologies selected, strategies applied and results obtained, are described with particular reference to Fuxin coal mine area in China.

Jan 1, 2014

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By Dong Liang, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"The formation, distribution and survival of pure Al nuclei under surface pulsed magneto oscillation (SPMO) treatment were investigated with thecombination of experiments and numerical simulation. The results indicated that the nuclei originated from the whole top surface of melt owing to the oscillation of top surface induced by SPMO. The temperature field significantly affected the survival of the nuclei The electromagnetic force and flow field of the melt with SPMO treatment were simulated by finite element software ANSYS. The electromagnetic force mainly distributed below the top surface near the mould wall. The electromagnetic farce not only made the melt oscillate but also increased the convection of meh below the top surface vigorously. The oscillation near the top surface of the melt promoted the nucleation largely, and the convection increased the uniform of the temperature distribution in the whole meh which favored the survival of nucleiIntroductionAs we all know, fine equiaxed grains are beneficial fur the improvement of the mechanical property, process ability and the uniformity of metallic materials [1-2]. With the researches of recent decades, people discovered that the electromagnetic field is an efficient method to refine the solidified structure of metals [3-7]. Pulsed magnetic field technology obtains more and more attentions in recent years due to its smaller power consumption, bigger instantaneous magnetic field intensity, non-contacting with the meh and simple convenient equipment manufacturing [8-9]. However, the melts would splash fiercely when pulsed magnetic field is applied with a slightly higher power. Thus, based on the understanding of the solidification refinement mechanism of electric current pulse (ECP) [10], Gong et al [11] developed a novel technology called pulse magneto-oscillation (PMO) to refine the solidification structure. The technology can be easily applied in the solidification structure refinement of continuous casting slab. But fur aluminum continuous casting, the sump is very shallow, which greatly limits the application of pulse magneto-oscillation technology."

Jan 1, 2014

By S. Jayasekera, A. M. T. S. Bandara, J. Kyle, E. Koenigsberger, L. Koenigsberger

The extraction of rare earth oxides from fluoroapatite rich phosphate concentrates often involves a weak acid leach of fluoroapatite and a sulphuric acid bake of the leach residue followed by water leach and precipitation to obtain an intermediate product. The main aim of this study was to determine and rationalize the solubility of rare earth metal ions in synthetic solutions representing various process liquors at the temperatures 40, 60 and 80oC. The liquors contained different acid and metal ion concentrations with respect to sulphuric acid, phosphoric acid and sulphate salts of sodium, magnesium, aluminium, potassium, calcium and iron(III). A solid of mixed rare earth carbonates was used as the source of rare earth metal ions. The solubility tests and characterization of solids using XRD were conducted at Murdoch University laboratories as part of the process development for the Arafura Resources Nolans rare earth project. The composition of initial carbonate solids and the solids and solutions formed after saturation were analysed for rare earth and other elements at TSW Analytical Laboratories in Perth using ICP-MS and ICP-OES. The precipitated solid in sodium-rich acidic sulphate solutions is the double salt NaRE(SO4)2 based on the solid assays. However, in acidic solutions free of sodium or of low concentrations of sodium the precipitated solid appears to be RE2(SO4)3.

Jan 1, 2014

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Christopher Tucker, Marcello Veiga

Social issues are increasingly recognized as significant inhibitors to mineral development projects. Increasingly social risk is being recognized as a key factor determining the success of a mineral investment. Groups opposed to a mine for social or political reasons often use environmental impacts, real or perceived, to prevent mine development. These risk factors depend largely on cultural perceptions of mining activities and must be understood as such in order to be appropriately managed. A first step to addressing social issues is inclusive, transparent and meaningful engagement of stakeholders. This process allows stakeholders to understand what the other parties value in order to collectively establish a common currency for development and the creation of mutual value. Expanding the scope of benefits and values a mine can bring is of increasing importance to mining companies who typically consult outside specialists remote from the mine site and late in the development timeline for this purpose. Training technical staff, engineers and geologists, who make initial and ongoing contact with local interests, in a holistic approach to mine development is crucial to successful and economic mineral development projects. Further extending this conversation to the general public, media governments and non-governmental organizations is a necessary step in developing a meaningful discourse on the benefit of mining activities.

Jan 1, 2014

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By Lorraine Kent

Excessive floor and side deformation are major problems in deep coal mine entries in Europe, and in particular in the UK where rockbolt support is used at depths of working of around 3000 ft. This has major economic and safety implications for the industry resulting in the potential for sidewall instability, disruption to mine infrastructure, (belt conveyors, floor mounted transport systems and powered supports), and the requirement to safely manage excavation of large quantities of floor material. European research aimed at improving deformation control is described. The outcomes include innovations in support systems, materials and installation practices, as well as better methods for predicting and monitoring deformation levels. As coal mines get deeper, some entry deformation is inevitable, and methods for mechanised removal of floor lift and repair of sidewalls have been developed to allow production to continue as mining clearances are re-established.

Jan 1, 2014

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014

Systemic process mineralogy study on Baerbulawu refractory hematite ore in Kazakhstan has been carried out. The ore contains Fe 41.34%, and 87.26 % of which exists in hematite. Most hema-tite occurs as fine or ultrafine grains and its average size is only 0.015mm. The gangue is mainly composed of quartz, mica, chlorite, kaolinite and other clay minerals. The liberation of hematite is only 66% when the ore is grinded to 75% ?0.074mm, while part of gangue is already liberated from hematite under this grinding condition, so these gangue can be cast away by magnetic separation in advance. Hematite will not liberate completely from gangue untill grinding fineness reaches 86% ?0.038mm, at the same time, free particles of ultrafine hematite tend to coagulate randomly with quartz and clay minerals, so appropriate dispersant is necessary to pre-vent hematite and clay minerals from coagulation. Based on the process mineralogy research, final technology flowsheet is high-intensity magnetic separation by coarse grinding?rough magnetic concentrate regrinding?inverse flotation, and an ideal index is achieved. The yield of final iron concentrate is 43.46%, and its grade and recovery are 66.76% and 70.55% respectively. The research result is also useful to other similar iron ores.

Jan 1, 2014

By S. Gerl

Since Schönert, 1980 a multiplicity of scientists have dedicated themselves intensively to the scientific investigation of wet grinding in agitated media mills. The achieved research results led to a clearly improved understanding of the comminution mechanism in wet operated agitated media mills and in consequence also to clearly more efficient machines. In contrast to this the standard of knowledge on dry grinding in agitated media mills is still very small. The practical experience from numerous plants shows however that the transferability of knowledge from wet grinding to the dry grinding regarding transport phenomena and comminution behaviour, influence of the operating parameters and also wear is very limited. In the industrial application above all the continuous mode of operation is preferred. The main problem which has to be solved in agitated media mills is minor the comminution itself, than rather the question of the trouble free material supply and material extraction as well as the cooling of the mill. The agitated media mill MaxxMill® offers an innovative concept to overcome the feeding and extraction problem with its rotating grinding chamber, the eccentrically mounted agitators as well as the eccentric flow deflector with integrated material supply. Because of the pneumatic extraction of the ground materi-al cooling of the milling chamber is not necessary. On a MaxxMill ® laboratory mill with a 5 litre grinding chamber volume extensive parameter studies were carried out to study the influence of operating parameters on the continuous dry grinding of quartz sand. The test were performed in a continuous single pass operation without classification of the final product. Apart from the influence of the throughput rate on fineness above all the influence of the agitator and grinding chamber speed as well as the grinding media size was examined.

Jan 1, 2014