Search Documents

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The investigated sulfide Cu-Ni ores are characterized by low PGE contents and emulgated impregnations of pentlandite and palladium minerals in the main ore-forming mineral pyrrhotite, which hinders their selective separation, requiring a collective flotation of sulfides to concentrate, and hydrometallurgical processing. As revealed by studies of floatability of Pt-Cu-Ni ore in a mixture of butyl xanthate and chelating phosphorus containing reagents, the most effective additive is Aerophine 3416 (a phosphinates mixture) manufactured by Cytec. Using collective flotation with a butyl xanthate – Aerophine 3416 composite in the ratio of 1:3 has afforded to enhance the Pt, Pd, and Ni recovery by 13.6 %, 9.2 %, and 9.4 %, respectively. The optimal ratios of Aerophine 3416 to butyl collector for the collective flotation are the following: 1:1 for Pt and Pd and 3:1 for Ni. The effect of these reagents on the electrode potential and surface hydrophobicity of pyrrhotite, pentlandite, and platinum black has been investigated. The extraction UV spectrophotometry experiments demonstrate that DIBDTPI exists on the pyrrhotite surface mainly in the form of disulfide in weak acid medium and in the form of compounds with Fe on the mineral surface in minute amounts. There appears some disulfide and few amount of (DIBDTPI)2Ni on the surface after interaction of DIBDTPI and pentlanditeINTRODUCTIONXanthates are widely used in flotation of copper-nickel ores containing platinum group metals (PGM) as sulfides collectors which can concentrate the most part of PGM connected with the sulfides. Though xanthates are hardly efficient for flotation of free PGM, the latter are floated more slowly compared to the sulfides of base metals. The reasons for poor floatation of free (mineral) forms of PGM are under-researched, however the key accepted reasons are: fine disseminations of free PGM, insufficient interaction with xanthate and negative influence of blue copperas and sulfur-containing ions which are sulfides oxidation products (Penberthy et al. 1999; Shackleton et al., 2007). That’s why an additional collector, normally dialkyldithiophosphates, is used during flotation of PGM-containing copper-nickel ores. A reagent DP-4 is used for recovery of PGM at Norilsk mining and metallurgical plant. The reagent represents a slightly-soluble organic calcium sulfonate which is given to flotation pulp in the form of water emulsion of 5% - solution in automotive diesel oil."

Jan 1, 2016

By Mostafa Benzaazoua, Emilie Ré, Raphaël Mermillod-Blondin, Hassan Bouzahzah, Jean-François Wilhelmy, University of Québec in Abitibi-Témiscamingue

"We analyzed two copper and lead flotation concentrates from the LaRonde mill using MLA technology (Mineral Liberation Analyzer) to identify the contaminants and to quantify their size and liberation. The MLA mineral quantification was compared with traditional mineralogical techniques (Scanning Electron Microscopy, Optical Microscopy, X-Ray Diffraction and Chemistry). The accuracy of MLA data was then quantify in application to metallurgical decision (mineral identification, mineral quantification, particle sizing and liberation quantification). We prepared five well-known materials from pure minerals and analysed them by MLA. MLA concentrates analyses showed the lead concentrate is mainly contaminated by pyrite and sphalerite. These minerals are liberated above 70 % and present a floatable size around 15 to 35 µm. Surface activation by dissolved lead from galena is therefore assumed for these contaminants. The analyses of the known samples show that mineral quantification and size distribution given by the MLA are consistent with the chemical analyses and the laser particle sizer. The liberation measurement is affected by the stereological effect. Modelling quantifies the overestimation of the particle liberation. Based on the modelling, the stereological shift on liberation should not impact metallurgical conclusions on the concentrate contaminations.INTRODUCTIONTo face the diversity of mineral processing challenges, the process mineralogy includes phase quantification, measurement of mineral size, liberation by exposure and by grade, association, surface contact proportion and texture. In the last decades, two SEM commercial tools emerged: MLA and QEMSCAN R. Both are based on specific combinations of backscattered electrons and X-ray images as well as image analysis routines developed at CANMET (Petruk & Pinard, 1976, Petruk, 1989), CSIRO (Frost, O'Hara, Suddaby, Grant, Reid, Wilson & Zuiderwyk, 1977, Reid, Gottlieb, MacDonald, & Miller, 1984) and JKMRC (Hall, 1977, Gu & Sugden, 1995). Recently, TIMA (TESCAN) and Mineralogic MiningR (ZEISS) supplied automated mineralogy for mining industry (Bouzahzah, Benzaazoua, Graham & Cropp, 2015, Gottlieb & Dosbaba, 2015a). In parallel, home-made routine were developped to resolve mineralogy challenges in mineral process but also in geometallurgy and mining environment (Kahn, Mano, & Tassinari, 2002, Knight, Klassen & Hunt, 2002, Mermillod-Blondin, Benzaazoua, Kongolo, de Donato, Bussiere & Marion, 2011, Hunt & Bradshaw, 2015). SEM mineralogy become essential to operation by setting units on mine sites (MacDonald, Latti, Adair, Bradshaw, & Dunn, 2011, Goergen et al., 2013, Dobbe et al., 2014, Gottlieb & Dosbaba, 2015b)."

Jan 1, 2016

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016

By P. L. Li, B. X. Song, C. H. Wang, T. Wang, Z. Hu

"The treatment of an oxidized copper-gold ore by stage cyanide addition was investigated. For cyanidation, free cyanide ion concentration can be an indicator of whether there is copper dissolved in cyanide solution, and maintaining the free cyanide ion concentration lower than 1.0 g/L could be an effective way to prevent copper dissolution and reduce cyanide consumption. For that purpose, stage cyanide addition was introduced to control free cyanide ion concentration within the range from 0.8 to 1.0 g/L. Cyanidation tests results indicate that gold extraction was still acceptable at reduced cyanide consumption with a lower copper extraction. Based on the experimental study, industry application works at Beiya concentrator of Yunnan province, China were successfully conducted. When the raw ore contains 2.95 ppm Au and 0.75% Cu, by stage cyanide addition method, the gold extraction was still 93% at reduced cyanide consumption of 2135 g/t, which was only half of one addition method, and the copper extraction dropped to only 5%, which indicated that dissolution was prevented for almost 75% of the malachites.INTRODUCTIONCyanide with its competency to form a strong complex with gold, is the most preferable lixiviant for gold leaching. However, cyanidation is not inherently a selective process since many other minerals present in the ore are also readily soluble, especially the copper minerals. Muir (2011) reported that every 1% reactive copper present in the ore consumes about 30 kg/t NaCN, which can have detrimental effects on the process efficiency and economics due to high cyanide consumption, reduced gold leach rates and poor gold recovery."

Jan 1, 2016

By Akira Ishikuro, Masamichi Shintaku, Futoshi Kusumoto, Takeshi Kudo

"The Bankei-Kitanosawa tunnel that is located in Sapporo, Hokkaido, Japan includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. The mucks containing hazardous materials were disposed into the waterproof branch tunnels created from the inside of the main tunnel. The full face early ring closure method was employed to ensure the stability of the tunnel in the low strength rock masses having no stand-up time. As a result, the waterproof tunnels branching off the main tunnel can manage water tightness so as to ensure safety and relief against environmental risks of the hazardous materials. It is also demonstrated that the full face early ring closure method enable construction of the tunnel with a small overburden in the low strength rock masses. INTRODUCTION The Bankei-Kitanosawa tunnel includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. In order to overcome the restrictions, the hazardous materials were designed to be disposed into large cross section waterproof tunnels which were newly designed and constructed in high strength and hazardous material free Andesite. The lining for the tunnels was composed of with shotcrete. In addition, full face early ring closure (Sato et al., 2013) was employed to stabilize the tunnel so as to enable safe tunnel excavation in low strength rock masses where a ground arch is deemed unachievable. This paper presents the safe disposal method of mucks which are likely to liquate out natural hazardous materials as well as the full face early ring closure method and its mechanical characteristics."

Jan 1, 2016

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. An alternative parameter, the organic efficiency, does indirectly consider process economics, but it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach, the partition moment of inertia, is introduced. This parameter reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure that promises better use of performance data. IntroductionPartition curves are commonly used in the characterization, evaluation and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, density separators and other beneficiation technologies that are based on intensive physical properties. Graphically, the partition curve depicts the recovery of particles as a function of the physical property on which the separation is based, such as particle density, size or magnetic susceptibility. Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic S shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout, or bypass, values; the midpoint slope; and the separation cut point, defined as the property value with 50 percent recovery.Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, as a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point, that is, an infinitely large slope. One common formulation of this slope, the Ecart Probable, Ep, is derived by evaluating the slope between the 25 and 75 percent recovery points:"

Jan 1, 2016

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By C. Eddine

"Can we use data to make communication effective? How does one successfully tackle the challenge of solving cultural differences and harmonizing the needs of diverse stakeholders while developing and maintaining a strong and reliable corporate image? Is it possible to achieve better engagement and minimizing risks with data? This paper aims to explore human rights and business procedures, the promotion of shared prosperity in a sustainable manner and the use of metrics to guide decision-making process. Among the topics examined are: • the significance of stakeholder engagement in community development projects; • the use of grievance mechanisms to give a voice to First Nations and communities / populations in vulnerable positions (including children and elders); • the benefits of configuring and implementing a feedback system in partnership with the communities. This research is a preliminary initiative and has limitations on the extent of the material used. The author acknowledges there is a vast amount of work and publications available on this subject, as well, as a variety of examples that have not been included. The intention is to keep developing this research to assess and expand how data can be used to minimize risks and improve engagement, in addition to inspire others to continue advancing this topic. Natural resources consumption is a reality that will not disappear in a foreseeable future. Several developments and operations are located in remote areas where communities in vulnerable situation and Indigenous Peoples live. Feedback systems are being ratified as a tool to help tackling the challenges of harmonizing cultural differences and fulfilling the needs of diverse stakeholders. Integrating social, environmental, and economic values plays an imperative purpose in preserving a productive and trustworthy relationship with stakeholders. Positioning social standards next to environmental and economic principles shows inclusiveness and firm intention of integration. We add value to a positive image of our industry by embracing responsibility for corporate actions and promoting their beneficial impact on the environment. The social context within communities, groups and organizations is dynamic and presents new challenges as connections evolve. There are wildly diverse expectations which one may need to address during exploration, construction and operating phases. Disagreements are an inevitable consequence of interactions due to the different needs and requirements of the parts involved. Nevertheless, balancing differences and solving conflicts can offer remarkable opportunities for improvement."

Jan 1, 2016

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By Osamu Nishikokura, Jumpei Yamashita, Darrell Liebno, Malcolm Sheehan

"The Eglinton-Scarborough Crosstown Project builds a 19km LRT corridor that includes a 10km underground portion, between Keele Street and Laird Drive. The West Tunnel Contract (ECLC1-15) includes 6.5km of twin EPB TBM bored tunnels with a 5.75m internal diameter precast concrete segment lining (PCTL), between Keele Street and Yonge Street. This paper summarizes the overall scope of work, the technical challenges faced and innovative solutions developed by the contractor during the TBM move across an existing subway tunnel using state of the art high capacity strandjack gantry crane.1. PROJECT OVERVIEW The Greater Toronto and Hamilton Area (GTHA) is Canada’s largest urban region, populated with over 6 million people, and is one of the most rapidly growing regions in North America. One forecast estimates that the population of this region will increase to 8.6 million by the year 2031. In September 2008, Metrolinx, an agency of the Government of Ontario, launched a 25-year regional transportation plan named “The Big Move” to cope with the expected increase in transportation demand. The Eglinton-Scarborough Crosstown, one of the projects included in “The Big Move”, is a light rail transit (LRT) that will run across Toronto in an east-west direction between Mount Dennis and Kennedy along Eglinton Avenue. In October 2012, the West Tunnel Contract of the Crosstown LRT (ECLC1-15) was awarded to Crosstown Transit Constructors (CTC), a joint venture between Obayashi Canada Ltd., Kenny Construction Company, Kenaidan Contracting Ltd. and Technicore Underground Inc. The project includes approximately 6.2 km long twin bored tunnels, 9 cross passages, 1 emergency exit building, 7 sets of station headwalls, and an intermediate pair of extraction and launch shafts. Each of 6.5 km long twin tunnels are divided by the existing subway station into two drives: the first half from the launch shaft LS-1 (west of Keele Station) to the extraction shaft ES-1 (west of Eglinton West Station), and the second half from the launch shaft LS-2 (east of Eglinton West Station) to Yonge Station, as shown in Figure-1. The TBMs are extracted at ES-1 and moved to LS-2 over the existing Yonge-University Subway Line at Eglinton West Station before resumption of tunneling at LS-2."

Jan 1, 2016

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy Joint Venture in Madagascar is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behavior and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and both intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behavior of iron.INTRODUCTION The main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. The Ambatovy ore is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. Since the nickel content of the ore is roughly one fortieth that of iron, successful recovery of nickel depends on close control of the behavior of iron in the selected process. Exploration of the Ambatovy area, which is located to the east of Antananarivo, the capital of Madagascar, dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy Nickel Project. Dynatec then became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan (Collins et al., 2004, 2005, 2009; Collins & Vardill, 2005). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy Nickel Project, in 2007. The current Ambatovy Joint Venture consists of an integrated nickel and cobalt mining, processing, refining and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner) and KORES (27.5% owner)."

Jan 1, 2016

By Alexandru Corneliu Stematiu, Catalin Popescu, Radu Sarghiuta

"The tunnel sector is excavated into a rock mass heavily affected by tectonics, defined as a regional fault. The rock around the tunnel support undertakes the non – elastic deformation and gradually detaches from the rest of the non affected rock mass, moving inside of the excavated area and tending to fill up the whole space. The initial solution of using stiff support consisting in double steel ribs I12 with circular shape in the upper part and straight vertical pillars in the lower part has proved to be inadequate. Based on the calculations of the subsidence phenomena and a mathematical model, the proposed alternative support was provided by special circular steel ribs – SG-23 –that allows a limited rib deformation (by relative slip between the arch segments) in order to mobilize the contact between the rock contour and the inner face of the rib - not only for the deformed rib but also for the neighboring ribs. 1. INTRODUCTION Hydropower development of Jiu river in Romania, in the narrow gorge sector includes two diversion HPP and a small hydro plant that provides the minimum required flow downstream: CHE Dumitra , CHE Bumbesti and MHC Livezeni (Table 1. Hydropower parameters).The Livezeni intake reservoir is provided by a gated dam located 1250 m downstream of merging point between Jiul de Vest river and Jiul de Est river. The dam is equipped with three radial gates with flap gates with a span of 12 m each and the height of (6 + 3) m. The longitudinal profile of Dumitra head and the location of the gallery zone that is the subject of the paper are presented in Figure 2. Longitudinal Profile – Dumitra Head."

Jan 1, 2016

By Robinson Leon-Diaz, Alberto Jaen-Toribio, Raymond Blanchard, Mike Deevy, Miguel Fuentes-Llanos

"Tunnels designed to NFPA 502 are required to withstand the RWS time-temperature curve, more specifically prevent progressive spalling and loss of strength of steel reinforcement. Fire boards or spray-on layers can be effective, however, these solutions have capital and whole-life cost implications. The use of “fire resistant” concrete based on a suitable aggregate with polypropylene fibers has also increased in recent years. This article presents a new methodology for thermal and structural analysis of segmentally lined tunnels, which permits the analysis of project specific fire curves and an assessment of different fire protection strategies. The effectiveness of fire boards is assessed along with whether “fire resistant” concrete alone is a viable means of achieving the required protection. Finally, since NFPA 502 recommends water-based fixed fire-fighting systems for Category C and D tunnels, we discuss the question of how a fixed fire-fighting system should be addressed within the structural design. INTRODUCTION Protecting road tunnels from structural damage and collapse is a key requirement for both life safety and business continuity. Where road tunnels are part of key highway corridors, protecting business continuity is a high priority for owners, operators and the Authority Having Jurisdiction. For existing tunnels, compliance with NFPA 502 may require upgrades with either passive fire protection and/or water-based fixed firefighting systems. For new tunnels, compliance with NFPA 502 requires a combination of good practice in design and fire testing. A water-based fixed firefighting system is a Conditionally Mandatory Requirement1 for Class C and D tunnels, i.e. all tunnels greater than 300m and 1000m long respectively. The basis for fire safety design of new tunnels and assessment of existing tunnels is the worst-case fire scenario. A number of factors, including but not limited to the following, influence this design fire scenario:"

Jan 1, 2016