Search Documents

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By Xiqing Wu, Liang Dai, Tao Yue, Longsheng Yi, Ruifang Wang

Magnetic seeding flotation (MSF), i.e. adding magnetic seeds and pre-magnetization-flotation, is a new flotation technology especially for fine particles, which improves the flotation performance by enlarging the apparent size of the particles in a way of magnetic agglomeration. Both the fine coal slimes with a size of 66.68% –38µm and the pyrite slimes with a size of 73.95% –23 µm were investigated by the MSF, respectively. Flotation tests with variable of dosages of magnetic seeds and polyacrylamide were conducted, and some measurements, such as laser diffraction size analysis, magnetic susceptibility by vibrating sample magnetometer (VSM) and infrared spectroscopy (IRS), were also applied in order to probe the mechanism of the MSF. Based on the tests, measurements and calculations it was found that both the recovery of coal and the flotation kinetics of pyrite slimes increased with the additions of the magnetic seeds, and in the presence of polyacrylamide the coal flotation was further strengthened due to a synergetic effect of magnetic seeds and polyacrylamide on the flotation and a relatively larger apparent size of slimes after additions of magnetic seeds and polyacrylamide. The reason for the MSF lies in fact that the presence of the polyacrylamide intensified the adsorption of magnetic seeds on the coal particles and increased the coverage of the magnetic seeds on the coal surface from 0.2 to 1.3 wt%, resulting in increased magnetic susceptibility of coal particles from 9.13×10-9 to 22.17×10-9 m3/kg and thus a low magnetic field strength of pre-magnetization needed for the magnetic agglomeration among the coal particles from 602 to 24 mT prior to proper flotation. IRS shows that polyacrylamide chemisorbed on the surfaces of both coal particles and magnetic seeds, thus acting as the bridging media between particles and seeds.

Jan 1, 2016

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By Jun Xiao, Xiaodong Li, Chunming He, Daixiong Chen

"Benzohydroxamic acid with double dentate can react with copper to form cyclic hydroxyl oxime acid copper chelate, indicating a good selectivity for copper oxide minerals flotation, especially for malachite. The flotation results of the pure malachite mineral show a strong synergistic collecting effect between hydroximic acid and xanthate at a ratio of 3.5:1, achieving a malachite recovery of 95.5% when certain sodium sulphide is used as a sulphidizing agent in the optimal pH range. Thanks to the synergistic collecting effect, the flotation recovery of malachite of a real refractory ore flotation ,can reach over 92% under the optimum condition, a 12% higher than the recovery achieved with the conventional collectors. In industrial application, the flotation of the copper oxide minerals is improved , leading to a high efficiency utilization of copper oxide resources.INTRODUCTIONBeneficiation of copper oxide ore is one of the recognized challenges in mineral processing industry. Copper oxide ore is a vital component of copper resource in the world, which has abundant reserves. Majority of sulphide deposits has oxidized zone on the top, and some deposits are oxidized to become the large and medium-sized oxide deposits (Willam & Chavez, 2001). Most copper oxide ores have problems in processing such as high slime consumption, poor floatability, complex ore property and low flotation recovery, so it is of great significance in beneficiation of copper oxide ores to develop an efficient collector, especially for malachite (Fu & Gu, 1997; Wen, 2010; Riet, Kier & Elford, 1980). At present, sulphidization-xanthate flotation is the most important method for treating copper oxide ore. In recent years, due to the decreasing ore grade, the utilization of refractory copper oxide ore draws more and more attention (Zhou, 2003), except for sulphidization-xanthate method, chelating flotation method (Lu, 2009), chemical beneficiation method (Lenormed, Salman & Yoon, 1979), microwave radiation flotation method, hydrothermal sulphidization-flotation method (Mao, Wen & Fang, 2014) and ammonia leaching of sulphide precipitation-flotation method (Lekang, Stevik & Bomo, 2003) have occurred."

Jan 1, 2016

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016