Search Documents

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017

By K. Avarmaa, P. Taskinen

"The solubilities of rhodium (Rh) in a molten silver alloy in doré-smelting conditions for treating copper refinery slime at temperatures of 1,000 to 1,300 °C were measured using a high-temperature equilibration-quenching technique and direct phase analysis by electron probe X-ray microanalysis. The results obtained indicate that the solubility of rhodium in molten silver is very limited: only 0.04 to 0.26 weight percent at 1,000 and 1,300 °C, respectively. The thermodynamic properties of rhodium in molten silver were estimated from the solubility data. The compositions of the solid rhodium alloys in equilibrium with molten silver-rich doré metal were also measured in this study. The excess rhodium in the doré alloy will precipitate during the refining as solid, greater than 99 weight percent Rh.IntroductionSilver refining is a core step of the processes of anode slime treatment and precious metals recovery in copper refineries (Hait, Jana and Sanyal, 2009; Ludvigsson and Larsson, 2003). It separates the oxidic materials, such as nickel oxide (NiO) and barium sulfate (BaSO4), from metallics after the de-coppering and de-selenation steps of the anode slime, and refines the silver bullion from the undesired elements present (Cooper, 1990; Hyvärinen, Lindroos and Yllö, 1989). Doré metal is a silver-rich alloy which after the smelting step will be refined electrolytically, and the remaining constituents of gold as well as the platinum group metals (PGM) will be subsequently recovered in their own processing stages.Because of low concentrations of PGMs in copper, they are typically soluble in the doré metal in anode slime treatment. This can be concluded from their binary phase diagram data with silver (Massalski et al., 2007). One exception is sometimes encountered in the anode slime smelting operations if the smelter feedstock is rich in rhodium, as may be the case if the raw materials contain secondary raw materials such as e-scrap. The solubility of rhodium in solid silver is less than 0.04 weight percent (Królas and Sternik, 1995), and its solubility in molten silver is highly uncertain. The only experimental information in the literature (Królas et al., 1993; Elliott, 1985) suggests that the silver-rhodium alloy system at 960 °C forms a eutectic, which locates less than 2 °C below the melting point of pure silver (Arblaster, 2015). Early observations (Rössler, 1900) propose that rhodium is insoluble in molten silver even if solid silver-rhodium solutions have been recently produced on a nanoscale (Kusada et al., 2010).The aim of this study is to measure experimentally the solubility of rhodium in molten silver at doré metal smelting and refining temperatures. The silver alloy used to mimic the doré alloy contained silver and about 1 weight percent of the alloying elements copper, gold, palladium, rhodium and tellurium. The experiments were carried out in metal-slag equilibria with nitrogen-oxygen mixtures as the atmosphere, employing an equilibration-quenching technique and using direct phase composition analysis by electron probe X-ray microanalysis (EPMA) (Jak, Hayes and Lee, 1995)."

Jan 1, 2017

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By D. Paul Bishop, Kevin P. Plucknett, Hung-wei Liu

"Spark plasma sintering (SPS) process has been evaluated for producing the commercially pure (CP) Ti, TiAl and a TiAl-B4C composite. Comparisons were made between the materials in terms of the sintered density, resultant hardness and microstructures. In the present work, the titanium aluminide powders (Ti-48Al, producing a mixture of y-TiAl/a2-Ti3Al) were synthesised „in-house? using a simple reaction-sintering and mechanical attrition approach. This allowed various size distributions to be generated. The powders were then blended with a fine boron carbide (B4C) powder (up to 6 wt.%), and the resulting mixtures were consolidated using spark plasma sintering (SPS) under vacuum in graphite dies. An applied stress of 50 MPa was used for all SPS runs. The SPS parameters were varied in terms of the ultimate sintering temperature (up to 1300°C) and hold time (up to 10 minutes) for each material. It is demonstrated that high densities can be achieved this approach (exceeding 95% of theoretical, with optimised samples close to full density). Microstructural characterisation was conducted using optical microscopy, scanning electron microscopy, and X-ray diffraction. The B4C additions were seen to partially react with the TiAl to form reinforcements, such as TiCx and TiBx. Preliminary mechanical property assessment will also be briefly discussed.INTRODUCTION Titanium- and titanium aluminide-based alloys possess many unique properties, such as excellent corrosion resistance and high temperature strength, respectively (Cardarelli, 2001; Leyens & Peters, 2003). Compared to many other competing materials (e.g. stainless steel or Ni-based alloys), Ti- and TiAl-based alloys also have relatively low densities (~4.5 and ~3.9-4.1 g/cm3, respectively), which is critical for performance in aviation and automobile applications. However, the manufacturing cost is high, due to the expensive raw Ti material and difficulties in machining. TiAl-based alloys are particularly difficult to produce because of their limited ductility (Lütjering & Williams, 2007). To overcome those problems, powder metallurgy (PM) technologies have shown great potential as near-net shape processes for Ti- and TiAl-based alloys. The general PM process largely avoids laborious post-machining and minimises material use. In industrial production, the PM approach has been successfully utilised to manufacture aluminium- and iron-based alloys (Huo & Heath, 2008)."

Jan 1, 2017

By M. Rylatt, E. Legault-Seguin, C. Mohns

"With energy costs increasing and ore grades diminishing, the role of preconcentration in hard-rock mining operations has gained greater interest. Dense medium separation is a process that can be conducted at particle sizes from 250 to 0.50 mm with high separation efficiency, depending on liberation characteristics of the valuable minerals. Pilot-plant case studies conducted at the SGS Lakefield site are presented, including mineral systems such as spodumene, sulfide-bearing gold ores, and complex sulfide ores. These case studies demonstrate that, for amenable ores, mass rejection of 20–60% is possible while maintaining recoveries of greater than 90%.RÉSUMÉ Au vu de la hausse des coûts liés à l’énergie et du déclin de la teneur des minerais, le rôle de la préconcentration dans les exploitations minières en roche dure présente un intérêt croissant. La séparation (ou concentration) en milieu dense est un processus pouvant être mené sur des calibres de grains de 250 à 0.50 mm avec un rendement élevé de séparation, en fonction des caractéristiques de libération des constituants des minéraux métallifères. Sont présentées dans cet article des études de cas menées dans des usines pilotes du site de Lakefield de SGS, lesquelles incluent des systèmes de minéraux tels que le spodumène, les minerais aurifères sulfurés et les minerais sulfurés complexes. Ces études de cas montrent que pour les minerais présentant les caractéristiques de libération appropriées, il est possible d’atteindre un rejet en masse de 20 à 60 %, tout en maintenant des récupérations supérieures à 90 %.INTRODUCTIONPreconcentration is the process of rejecting gangue minerals while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Preconcentration has been practiced in the industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, which typically require finer grind sizes and incur higher energy costs.The benefits of preconcentration are:• lower mining costs, which allows for nonselective mining;• lower process capital and operating costs (e.g., resulting from reduced grinding, flotation, and fines disposal stages);• increased ore reserves, which provides the potential to treat lower grade ore;• increased mine production without expansion of the existing plant or concentrator;• reduced overall tailings impoundment by converting the reject into a byproduct (e.g., underground backfill or aggregate);• improved efficiency of downstream processes (e.g., silica removal in electric arc furnace feed, removal of softer sliming minerals prior to grinding);• potential application to brownfield operations and greenfield projects; and• a “green” process option, which reduces processing energy consumption;– reduces mill feed;– increases stage metal recovery (higher grade feed);– increases mill metal output per tonne processed;– reduces surface plant, tailings dump, and tailings pond requirements because the plant has a small footprint and can be installed underground; and– can be applied to retreatment of old tailings dumps to recover metal values and reduce environmental impacts (e.g., dissolved metal runoff, acid drainage)."

Jan 1, 2017

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By Baohua Guo, Xuelin Yang, Tingkan Lu, Hailin Sun

The work presented in this paper mainly involves two parts. Firstly, the fundamental characteristics of the high pressure carbon dioxide gas fracturing technique (CO2 technique), including, a proposed method of TNT equivalence calculation, which is used to calculate the TNT equivalence of discharge of CO2 technique, and the comparison of the explosion volume generated by dynamite and expansion volume of liquid carbon dioxide is conducted to show the differences of fragmentation capacity between the two of them. Secondly, the coal seam fragmentation mechanisms of CO2 technique are proposed, including, 1) Gas jet cutting and penetration by shaped charge, 2) Gas volume expansion by changing phases of carbon dioxide, 3) Coal seam softening by destress blasting and 4) Coal seam fragmentation by discharge vibration, associating with the mechanisms, the equations for calculating fragmentation radius are developed and verified.

Jan 1, 2017

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

By Mark Vardy, Kate Dobson, Isobel Yeo, Paul Lusty, Bramley Murton

In response to anthropogenic climate change, the way in which we use and generate energy is changing. To facilitate these developments, it is essential that we increase and diversify the supply of ‘E-Tech’ elements essential for cleaner energy generation and more efficient usage. The vast majority of these materials (e.g. cobalt, lithium, niobium, platinum group metals, rare earth elements and indium) come almost exclusively from mining and new resources must be found and developed in order to secure supply and meet the demands of the future. Ferromanganese (FeMn) crusts are rich in cobalt, tellurium and rare earth metals, and are common on seafloor hard grounds at water depths over 1000 m. The mining of both FeMn crusts and nodules is potentially viable dependent of the balance of cobalt and nickle prices (Martino & Parson, 2012), however, crusts need to be at least 4 cm thick with cobalt contents of at least 0.8% (International Seabed Authority, 2008). The difficulty for those wishing to exploit these resources is firstly finding them, and secondly assessing their potential remotely. Such capability would not only save time and money, but also allow mining operations to be more focused, reducing needless destruction of seafloor habitats from exploratory mining or mining of noneconomically worthwhile deposits. In this contribution, we examine the distribution of crusts on a single Atlantic Gyot (Tropic Seamount), the morphology of FeMn crusts, their variable growth patterns and the characteristic geophysical response from crusts in various datasets, including ship based 60 m resolution multibeam and high resolution bathymetry, backscatter and sub-bottom profiler data acquired using an Autonomous Underwater Vehicle (AUV).

Jan 1, 2017

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By C. Fuellenbach, J. Brune

"INTRODUCTION Mining activities must be safe and profitable. These two requirements influence each other. The purchase and implementation of safety improvements costs money. Injuries and illnesses at mines stop or delay production and may result in additional costs or a loss of profit. Other effects of injuries and illnesses include the negative influence on employee morale, corporate reputation and conflicts with contract partners. Based on this researchers asked the question: are mines with lower rates of injuries and illnesses more profitable than mines with a higher frequencies? One aspect of this research is the evaluation of the safety situation and the measurement of benefits of safety improvements in the German mining industry. In the following paper, this part of the research will be examined. The main aim is the evaluation of injury rates in different German mining sectors and regions in Germany. SELECTION OF GERMAN MINING OPERATIONS The research team decided to focus the study on the salt and potash and the aggregate and industrial minerals mining industries in Germany. These two mining industries are different in the number and size of operators, structure of the industry, pricing and markets. The selection of two different industries adds to the clarity of the evaluation. Salt and potash mining industry The German salt and potash industry is primarily located central Germany. All salt and potash mines in Germany are underground operations. In 2015, the German potash industry employed 8,100 employees and generated a total revenue of 2 billion Euros. German potash reserves include magnesium compounds like kieserite (MgSO4·H2O), in addition to sylvite (KCl) and carnallite (KMgCl3·6(H2O)). The German salt industry employed 2,300 people in 2015 and generated revenue of 800 million Euros (Krueger, 2015) There are seven mining companies with salt and potash operations: esco-european salt company GmbH & Co. KG, K + S Kali GmbH, Saline Luisenhall GmbH, GSES Glückauf Sondershausen Entwicklungs- und Sicherungs-gesellschaft GmbH, Südwestdeutsche Salzwerke AG, Wacker Chemie AG and Südsalz GmbH. In this way, esco – european salt company GmbH & Co. KG is an affiliated company. Esco was founded as a joint venture of K + S and Solvay in 2002, since 2004 K + S is the sole holder (esco - european salt company GmbH & Co. KG, 2016). Likewise, the Südwestdeutsche Salzwerke AG has a controlling interest in Südsalz GmbH (Südsalz GmbH, 2016). Aggregate and industrial minerals mining industry The aggregate mining industry in Germany is comprised of many small mining operations and relevant companies. According to the German Department of Economics (BMWi, 2015), the following industrial materials are classified as aggregates: fluorite, barite, kaolin, quartz and quartz sand, quartzite, silica, loamy and foundry sand, pegmatite sand, shale, clay, bentonite, schistose, limestone and dolomite, gypsum and anhydrite, basaltic lava and lava sand, gravel and split, pebble and silicic sand and peat."

Jan 1, 2017