Search Documents

By E. W. Parker

Anthracite, as sent to market, comes under three general terms of description: characteristics, source and size. Anthracite is generally classified as white ash, red ash, or Lykens Valley. The white ash coals are sometimes further described as "hard" or "free-burning." Lehigh white ash would come under the former description and Shamokin white ash under the latter. As a rule, it may be said that the nearer the origin of the coal to the western extremity of the anthracite region, the softer and more free-burning it is. Indeed, for many years the coal from Trevorton, at the western tip of the Middle Western field, was classified as "semianthracite" in the shipment reports. Lykens Valley coal is always a red ash coal, with a higher volatile content than the general run of anthracite, and consequently free-burning. The name does not exclusively indicate the neighborhood in which the coal is dug, but rather refers to the beds from which it is obtained. These beds lie, not above the Pottsville conglomerate, as is the rule, but encased in it. The extreme eastern limit of the Lykens Valley beds would seem to be about Tremont, in Schuylkill County, and the Natalie mine, near Mount Carmel. There are, of course, traces of these beds farther to the east, but they do not seem to be workable. There are as many as six of the Lykens Valley measures found in the conglomerate at some points, but to a large extent they are unworkable. Whether this coal is obtained in the Lykens Valley proper, where the beds were first identified, or from the Shamokin Valley, it is always Lykens Valley coal, and it has long been considered a premium coal, especially desirable for domestic use, particularly when a quick, hot kitchen fire is desired. Coals are, of course, frequently marketed under special names—Jeddo, Scranton, Kingston, Old Company Lehigh, Famous Reading, Lacka-wanna, etc.—which, of course, have the trade significance which their producers and vendors have built up. General Description of the Various Coals, with Name of Seam and Producing District This is partly covered in the paragraphs above. Lykens Valley coal is produced from one or another of the six Lykens Valley beds lying within

Jan 1, 1930

The following discussion occurred on the afternoon of Sept,. 22, 1930, as part of the fall meeting of the Iron and Steel Division at Chicago. About seventy-five men attended this session. C. B. Murray opened the meeting, as follows: C. B. Murray, Cleveland, Ohio.—It is very encouraging to see so many here this afternoon to discuss this important matter of beneficiation. The producers of ore, I am sure, are anxious to furnish the grade of ore that the consumer wants. The consumer sometimes wants that which cannot be economically produced and often the producer cannot understand why the consumer wants certain things. It was to bring together these two interested parties that this meeting was proposed. I was appointed the chairman of the meeting, chiefly because I happened to be the chairman of the Iron Ore Committee of the Institute. I know a little about iron ore but have not perhaps kept up with the times in blast-furnace practice. I am asking Mr. Sweetser, who is well informed from both sides, to take over the meeting and carry on the discussion. R. H. Sweetser, Columbus, Ohio.—We want to have a free discussion between the iron-ore men and the blast-furnace men as to just what we are trying to reach in the beneficiation of iron ores. Many of those present have had a great deal of experience. There are men here from the ranges who have been passing through the experimental stage of beneficiation of iron ores, and there are some who have already gone on to commercial production. We have reached the point where the beneficiation of iron ore is important to the whole iron and steel industry. The connection between iron-ore beneficiation and the cleaning of coal is so close that I think we can profit by working very close to the coal people. Some Aspects of the Iron-ore Situation W. G. Swart, Babbitt, Minn.—I was very much interested in Mr. Richards'* paper on tonnages and the 20-year life. There is one interesting thing about the ore reserves; that is, the irregular distribution of that tonnage. On the Mesabi Range, for example, the United States Steel Corpn. owns between 70 and 75 per cent. of the reserve tonnage. They ship bctween 40 and 50 per cent. of the annual Lake Superior

Jan 1, 1930

By Horace Freeman

The sulphur consumed in Canadian pulp mills and acid plants is worth approximately three million dollars annually and amounts to one hundred and fifty thousand long tons, all of which is imported from the United States. Concurrently with a decline in the value of newsprint there has been a gradual increase in the price of this raw material. Most pulp mills in Canada are situated within reasonable distance of domestic pyrite deposits; nevertheless it has not yet been found possible to mine these deposits and utilize the contained sulphur in competition with the imported material. It is the purpose of this paper to elucidate the reasons therefor, and to describe? a commercial-scale experiment undertaken with the object of introducing a native raw material into the Canadian pulp industry on the purely economic basis. Reasons for the Preferred use of Sulphur The known sulphur deposits in the United States are very large, so that at least a twenty-year supply of this material is assured. It is recovered cheaply and in pure condition. Although large deposits of pyrite are known in Canada, nothing has yet been developed to compare in size, cost of mining, or purity with the United States material. It has been necessary to handle and transport more than two tons of pyrite to equal a ton of sulphur.

Jan 1, 1930

By R. Duncan Gardner

This paper describing the milling practice at the concentrator of the Harmony Mines Co. is one of a series being; prepared by the Bureau of Mines on milling methods and costs in the United States. For the period February 15, 1929, to June 1, 1929, the concentrator treated 200 tons of copper ore per day containing 3.84 per cent copper and recovered 99.2 per cent of the total copper in concentrates averaging 26.61 per cent copper. Milling practice at the Harmony Mines is in most respects similar to the usual practice at the average flotation concentrator producing bulk flotation concentrates. The exceptionally high recovery is due to a number of minor conditions. These minor details will be stressed throughout this paper.

Jan 1, 1930

IF lead be heated with concentrated sulphuric acid two distinct actions will usually be observed. In the first, bubbles begin to be evolved more or less rapidly from the lead, and in the second, which occurs at a higher temperature than the first, hydrogen and sulphur dioxide are evolved, free sulphur is liberated, and leadsulphate is formed. The second action may be violent and usually continues till the lead is all consumed.Attempts have been made to apply these reactions, by means of a standard procedure, as a "Flash test" for the acid resisting qualities of chemical sheet lead. The purpose of this article is to comment on the best method of performing the test, on the various phenomena which may be observed during the course of it and on the interpretation of the results when obtained.PREVIOUS WORKIn 1919, Barr...

Jan 1, 1930

By F. D. DeVaney

[In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Minn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Josoph and Kinney5 in venting about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say:]

Jan 1, 1930

By F. R. Wadleigh

There are in commercial use today in the United States various classifications of coal, each based on one or more characteristics. The bases of these classifications may be described as follows: GeNeRaL Basis Examples 1. Geological By seams and basins (local). 2. Chemical By constituents, as determined by analysis—ash, volatilc, slilfur and hcating value. 3. Combustion Characteristics As frce-burning, smokeless, character of ash. 4. Carbonization Characteristics Coking, noncoking. 5. Physical Characteristics Splint, soft, hard, block. 6. Geographical States, Fields, Counties, Districts. 7. Sizes By dimension or name. 8. Company Names Producing or sales company names, as "C. C. B. Pocahontas," etc. 9. Trade Names, copyrighted or not 10. Uses Gas, steam, coking, locomotive, fuel, bunkers, etc. 11. Use Methods Stoker coal. 12. Pools (Tidewater Exchanges) Analyses Size Seams Railroads Uses Structure Districts There are also classifications founded on more than one basis, as follows: 1. Geographical and Geological. By locality of mines (State, District, County) and seam. Examples: Cambria County, Miller Seam, New River, Sewell Seam. 2. Geographical and Chemical. Alabama medium volatile. 3. Combustion Characteristics and Ash Content. Free-burning, red ash (anthra- cite). 4. Carbonization Characteristics and Analysis. Noncoking, high-volatile, low sulfur. 5. Physical and Carbonization Characteristics. Splint, noncoking. 6. Size and Use. ¾-in. gas coal; domestic sizes (prepared sizcs); stcam sizcs. 7. Company Name and Seam. Consolidation Co., Elkhorn. 8. Size and Analysis. Low-volatile run-of-mine; low-volatilc slack. 9. Sizes—size of screen and name. 6 by sin. lump. 10. Chemical and USP. High-volatile steam. 11. Geographical and Use. Youghiogheny gas. 12. District, Size and Use. Pittsburgh gas l¼-in. lump. ,

Jan 1, 1930

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

By Alfred Beasley

LEAD-REFINING practice at the. Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill-has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1.

Jan 1, 1930

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930

By C. G. Maier

The fundamental chemistry of zinc smelting, especially that part dealing with the chemical reduction of the zinc-oxide content of a roasted zinc ore, has been discussed by metallurgists in some detail, but, in the light of present knowledge, unsatisfactorily. A considerable portion of the information available has been qualitative, or quantitative in a sense that could not be interpreted chemically. A number of attempts to elucidate the physical chemistry of zinc oxide reduction have been based upon unsubstantiated and, as is now known, incorrect equilibrium data. To write upon the chemistry of zinc smelting at this time, when electrolytic methods for the production of zinc metal from ore are becoming increasingly widespread, may seem a belated effort. So, for example, C. A. Hansen,3 in the communicated discussion of an article by the author,4 writes as follows:

Jan 1, 1930

By Chas. F. Jackson

During the past year a special study was made of shrinkage stoping A large number of mines in the United States and Canada which employ this method were visited and their practices were discussed with the operating staffs. The operating data obtained are appended hereto. Data were also abstracted from the literature on other mines and are combined in tables with data personally secured by the author. References are made to these published articles, some of which have appeared as information circulars of the United States Bureau of Mines, in the Transactions of the American Institute of Mining and Metallurgical Engineers, and the Engineering and Mining Journal. Several of the mines referred to which have not been described in individual papers will be described in detail in information circulars to be issued by the bureau. Eventually it is planned to combine and condense the information in these circulars and present the data in bulletin form.

Jan 1, 1930

By R. R. Brandenthaler

The development of the Seminole area into one of the major oil-producing sections of the country has been accompanied by many innovations and departures from former methods of development. On July 1, 1929, two years and nine months from the date of discovery, 20,490 acres were considered proved, and additional acreage is constantly being developed. Because of its peculiar conditions, extent, and rapid rate of development, the Seminole area provided numerous problems, the solution of which necessitated research in connection with practical field operation; as a result, there was a radical departure from methods usually employed in the development of a new field in the Mid-Continent area.

Jan 1, 1930

By Robert H. Ridgway

This circular outlines salient facts regarding the sulphur industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. It will welcome comments, criticisms, and contributions of data that may assist in making later editions of this circular more accurate, or in developing more fully the bureau's mineral files pertaining to sulphur. Throughout this paper sulphur is used to designate crude sulphur or brimstone, not sulphur produced from pyrites or' smelter gases.

Jan 1, 1930

By Paul M. Tyler

The literature on radium is already voluminous, but mcuh of it is too technical to be intelligible to the average reader, and there is no single publication that covers certain economic features of the radium industry. As a result of the renewed interest in the possibilities of domestic carnotite deposits a number of requests have been made to the Bureau of Mines for information, more particularly with reference to the business aspects of the industry. In order to meet this apparent need, the present paper has been prepared from material available in the files of the bureau. The technical data are compiled from various sources and are believed to be reasonably dependable, but the attempt has been not so much to achieve meticulous scientific accuracy as to brim; together facts of industrial significance and popular interest. GENERAL DESCRIPTION Radium is a brilliant white metal that melts sharply at about 700°C. and volatilizes appreciably at that temperature. With an estimated specific gravity of nearly 6.0, it is more than twice as heavy as aluminum and 25 per cent lighter than irons. Although it has been isolated in its metallic state, it is not used in that form, partly because it tarnishes rapidly even in dry air (forming a nitride), partly because of the greater expense of reducing it to metal, and partly because of the difficulty of dealing with such minute quantities of material. It is used always in the form of its compounds, the most important of which from the vie point of utilization are the bromide, chloride, and sulphate.

Jan 1, 1930

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By AIME AIME

THE Tuesday afternoon session", H. A. Bedworth chairman and T. S. Fuller, vice-chairman, was opened with D. J. McAdam, Jr.'s paper entitled "The Influence of Cyclic Stress on Corrosion." This paper dealt with the influence of cyclic stress on corrosion of alloy steels, corrosion-resisting steels, monel metal and aluminum alloys. The paper was discussed by T. S. Fuller, who pointed out that steels under stress corroded more than unstressed steels when subjected to steam.

Jan 1, 1930

By R. J. Colony

MINING geology does not lend itself - very readily to a review embracing "improvements in methods," as perhaps do shop practices or laboratory procedures. The "methods" used in mining geology are simply the application of geology to mining; winning the ore, the handling of material, mechanical appliances, all belong strictly to mining proper, and have no place in a review of geology as applied to mining. A comprehensive review would necessarily cover a .very broad field, which could be subdivided into many -parts. Only a few of these can be discussed here. .Those that have been suggested to the chairman indude :

Jan 1, 1930

By HARRINCTON EMERSON

UNEMPLOYMENT is the most ominous shadow ahead of the industrial nations today. Only two great industrial countries are free from unemployment, France and the Soviet Commonwealth. In France the social unit is the family, not the individual. This has saved France. In the Soviet Commonwealth, development is proceeding so rapidly from agricultural to industrial that there is still a dearth of muscle workers in the non-agricultural enterprises. In the other industrial countries unemployment results both from acute temporary recession in industrial activities and from the rapidly increasing substitution of the machine for the man. Temporary recessions can be mitigated, alleviated by makeshifts, often ill considered. Secular recessions due to a fundamental change in the way of accomplishing physical, chemical results cannot be cured by any makeshift. There must be a period of transition. There is therefore before us the three- fold problem, immediate, prosimate and ultimate.

Jan 1, 1930