Search Documents

By Oswaldo Delfim

Com o aumento da exportação do minério de ferro para os mercados asiáticos e consequentes novos parâmetros nas especificações, principalmente granulométricas para o minério com maior grau de pureza, viabilizaram-se importantes mudanças no processo produtivo, como por exemplo, a classificação do minério em sua umidade natural. Os ganhos adquiridos nesta nova condição de processo vão desde o aumento da recuperação mássica (de 90 a 95 para 100%), menor investimento no Capex e Opex, além dos ganhos na área ambiental como a eliminação da água na rota do processo e das barragens de rejeitos com consequente facilidade na obtenção do licenciamento ambiental. Neste artigo apresentamos os detalhes técnicos das condições dinâmicas ideais da peneira vibratória dedicada a esta nova aplicação.

Aug 16, 2017

By Lidong Teng

ArcSaveTM is a new generation of electromagnetic stirrer (EMS) from ABB for electric arc furnace (EAF) operation. Its goal is to improve the safety, increase the productivity and reduce costs. Electromagnetic stirring in the melt bath during arc furnace operation will affect the scrap smelting, bath temperature distribution, refining reactions, and also the tapping practice. This paper has summarized the investigation results obtained from the first ArcSaveTM system installed in a 90 ton EBT arc furnace in USA. The hot test results show that ArcSaveTM has enhanced the heat and mass transfer in the arc furnace process. This results in a faster scrap melting rate, lower slag superheat during arcing, more homogenous melt bath, higher decarburization rate and higher EBT free opening frequency. ArcSaveTM has also reduced the tapping temperature and tapping oxygen in the steel. This brings a higher scrap yield and saves ferroalloy consumption in the downstream ladle furnace operation. The lower energy consumption, short tap-to-tap time, and consistent furnace operation bring increased productivity and safety.

Aug 16, 2017

By Cristina Escudero Martinez

The purpose of the Basic Oxygen Steelmaking (BOS) is to refine the hot metal produced in the blast furnace into raw liquid steel, which may be subsequently refined in the secondary steelmaking shop. Appropriated fluxes for the BOF could require low melting point to reduce the energy consumption, to reduce the energy to fluidity the slag at lower temperature and to melt at lower temperature than steel. It is necessary a good Tumble test result and the fluxes do not generate fines which could obstruct the blowing plugs, so we would have a homogeneous flux. A homogeneous chemistry that allows to control the basicity (Si and MgO levels) and a high absorption characteristics to combine the flux with P, S, Si, etc. are necessary. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification being olivine and serpentine its principal minerals. It is formed by orthopyroxene, clinopyroxene and olivine in variable proportion. Dunite is a very homogeneous and hard stone. The main characteristics are: High hot and cold resistance to mechanical stress (shatter / crushing / abrasion), softening and melting points of a flux, not a refractory material, large porosity which is increased more than 20% when dunite is heated at BOF process temperature, and high absorption level, and stable components with low melting points. PASEK Dunite is a good flux in BOF process and its use is recommended if the BOF process produces pig iron with low Si content, generates high levels of slag and it is necessary maintaining the basicity index and the MgO amount and with high value of hot metal ratio (high amount of phosphorus to remove).

Aug 16, 2017

By André Luiz Vasconcellos da Costa e Silva

O sistema ferro-oxigênio alumino tem sido investigado há muitos anos em função de sua importância para a indústria do aço. Uma grande fração de todo o aço plano produzido é de aço de baixo carbono acalmado ao alumínio, não apenas pelo baixo conteúdo de oxigênio residual em solução que pode ser obtido mas, também, pela importância do alumínio residual na formação de AlN, ferramenta importante no controle de estrutura e textura obtidas. O sistema Fe-O é relativamente bem compreendido e quantificado, da mesma forma que o sistema Fe-Al. Entretanto, há discrepâncias significativas na quantificação do comportamento do sistema Fe-Al-O havendo, ainda, bastante controvérsia com respeito a equilíbrios importantes. Assim, o objetivo deste trabalho é (a) realizar uma revisão crítica dos experimentos e avaliações termodinâmicas principalmente do equilíbrio Al-Fe-O–Al2O3 (b) avaliar os métodos atualmente usados para descrever este equilíbrio e (c) apresentar recomendações sobre os dados, com base em sua confiabilidade e consistência.

Aug 16, 2017

By Marco Castenetto

Some of the most significant Danieli innovations in the field of long products are the: i) The EWR® system, through automatic continuous head-to-tail flash welding of billets at reheating furnace exit side, enables uninterrupted production of the mill for endless rolling of straight bars, wire rod and bar in coils. The process is particularly beneficial to wire rod and bar-in-coil mills as it enables production of “customized-size coils” (any coil weight according to specific Customer request) and with extra-high final coil weight, even starting from low-weight billets; ii) The Spooler process is based on twistfree winding of hot-rolled rebars into highly-compact/ultra-heavy coils featuring a unique cobble-free un-coiling capability. This enables high-speed feeding of the downstream cold-processing lines with hot-rolled spooled coils coming directly from the rolling mill without the need of any traditional off-line operation (such as de-coiling, stretching & re-winding). The system results highly beneficial both to bar-in-coil producers and to the downstream lines operators. The latest step forward is the combined application of these two systems that has made it possible for endless rolling of spooled bar in coils, enabling to cumulate the benefits of the two processes, particularly as far as transformation costs are concerned.

Aug 16, 2017

By Alexandre Rizek Schultz

Silat, Siderúrgica Latino-americana, selected Russula as the main engineering contractor for their 700,000 tpy Greenfield steel plant dedicated to long and flat steel production. The project is currently under construction in the district Guararu in Caucaia in the metropolitan region of Fortaleza. The project will be developed in two phases. First phase: 600,000 tons per year rebar mill and 60,000 tpy steel mesh line; Second phase: 700,000 tpy melt shop (90 ton/hr EAF and 4 strand continuous caster for billets up to 180 mm x 180 mm).

Aug 16, 2017

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Jerin Russell

This paper presents a new instrument for real-time detection of excessively coarse material in the overflow pipes of individual hydrocyclones using a non-invasive acoustic measurement technique. The hydrocyclone is an important device used in mineral processing beneficiation circuits for classification of mineral slurries by particle size. It separates a single input stream into two output streams; an underflow of coarse particles that undergo additional grinding for further size reduction, and an overflow stream of finer particles that typically goes directly into a flotation circuit for recovery of the desired mineral. However the hydrocyclone is a major piece of equipment in the beneficiation process that has no instrumentation for directly measuring its performance. The parameters currently measured – inlet pressure, feed flow rate, feed flow density – are common to the entire hydrocyclone cluster which typically has three to twelve hydrocyclones. Thus no information is available to detect individual hydrocyclones that are operating poorly. The system described in this paper detects the presence of unwanted excessively coarse material in the overflow stream of a hydrocyclone using sensors mounted to the exterior pipe surface. It provides real-time monitoring, trending and alarming of the coarse material level. This enables operators to identify poorly performing hydrocyclones, and enables corrective action to reduce or eliminate the coarse material discharge. Improving the classification efficiency of individual hydrocyclones will improve the overall classification efficiency of a hydrocyclone cluster. This leads to less variation in the particle size distribution and slurry density in the flotation feed, which will in turn improve overall mineral recovery. The reduction of unwanted coarse material in the flotation feed reduces the accumulation of that material in flotation cells. This can lead to equipment damage, and unplanned shutdowns due to events such as blocked dart valves.

Aug 16, 2017

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By Amélia de Santana Cartaxo

A pedra cariri, devido a sua extração, produz um alto teor de formação de sobras, o qual polui muito os arredores dos municípios, prejudicando rios e relevos da região. O presente trabalho tem como objetivo caracterizar o resíduo da pedra cariri, juntamente com uma argila para propor seu uso na formulação de blocos de vedação. Inicialmente a pedra cariri e a argila foram beneficiadas. Estes materiais foram submetidos a um ensaio de plasticidade pelo método pfefferkorn, e posteriormente á analises de difração de raios-x e de fluorescência de raios-x, para saber suas composições mineralógicas. Através da fluorescência e da difração de raios-x comprovou-se que a pedra cariri possui um teor elevado de CaO(89,0%), que ajudará na densificação da peça e no abaixamento da temperatura de queima, e que a argila tem um percentual bom de sílica livre, que ajudará na eliminação do gás CO2 decorrente da decomposição térmica do carbonato presente na pedra cariri, ajudando também na estabilidade dimensional da peça. Pelas analises feitas, percebe-se um potencial de uso da pedra cariri na formulação de massas para fabricação de blocos de vedação.

Aug 16, 2017

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Claudio Pereira Diogo

A lot of galvalume/aluzinc steel sheet was furnished to a metallic roof manufacturer intended for tile fabrication. But, according with the roof manufacturer, that coils develops a different superficial aspect during processing. The purpose of this work was to provide an explanation for the appearance of the observed surface on one side of the coils. In order to find out the origin of the problem, mechanical and microstructural characterization tests were done at INSPEBRAS with the support of a partner laboratory. The results are described in this paper with their analysis and conclusions.

Aug 16, 2017

By Daniel Augusto Godinho de Carvalho

Since the beginning of BOF process, slag formation has been subjected to extensive development. During the initial stages of the blow, fast slag formation is primordial for the process performance. This is mainly to allow oxidizing reactions, and also to protect the refractory. A modeling of BOF process for the purpose of process optimization requires precise knowledge concerning the dissolution of CaO and MgO based materials. Using this knowledge, the optimal process conditions can be ensured by a controlling of the slag formation during the converter steelmaking process. Taking into account an application of large amount of different raw materials, as well as location-specific process conditions, the characterization of the dissolution behavior of different additives is an important key to improve the technological process. Thereby, in the frames of this project, an appropriate model for slag formation is established and compared to operational results for a 330t BOF, operating at ThyssenKrupp CSA, Santa Cruz, Brazil.

Aug 16, 2017

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017

By Danilo Fontes Ferreira

O presente trabalho estudou o comportamento de uma liga de titânio ASTM-F67Gr1 frente à corrosão e à tribocorrosão em meio fisiológico. Para a realização desta pesquisa foi desenvolvido um aparato experimental capaz de impor simultaneamente um desgaste mecânico e corrosivo às amostras testadas, visando avaliar o comportamento tribocorrosivo. O meio corrosivo selecionado foi a solução de Ringer. A partir de curvas de polarização potenciodinâmica foi possível obter os parâmetros eletroquímicos necessários à realização dos ensaios de tribocorrosão bem como comprovar a excelente resistência a corrosão do titânio na solução de Ringer. A partir dos ensaios de tribocorrosão foi constatada a influência da velocidade e da carga aplicada, no fenômeno de tribocorrosão. Os resultados evidenciaram uma maior influência da velocidade no incremento da corrosão e da carga aplicada no incremento da sinergia, durante o desgaste tribocorrosivo.

Aug 16, 2017

By Vinícius Carvalho Teles

Durante a estampagem, ocorre o desgaste na superfície da ferramenta devido ao deslizamento entre a ferramenta e a peça. A manutenção das ferramentas de conformação envolve o polimento das bordas ou, em casos mais severos, a substituição da mesma é necessário. Ensaios de deslizamento alternado em revestimentos CrAlSiN depositados sobre aço ferramenta evidenciaram mecanismos de desgaste abrasivo devido a partículas de desgaste anteriores. O objetivo deste trabalho foi investigar a resistência a abrasão destes revestimentos, onde variou-se a topografia do substrato e arquitetura do revestimento, a composição química e a espessura. As propriedades mecânicas destes revestimentos foram avaliadas utilizando ensaios de esclerometria com carga progressiva e microdureza Knoop. A resistência à abrasão foi avaliada utilizado testes de microabrasão com partículas abrasivas de SiC. Os resultados mostraram que não houve diferença nas taxas de desgaste entre as duas arquiteturas. Maiores taxas de desgaste foram obtidas ao diminuir o teor de AlSiN na superfície e ao diminuir a espessura. Também foi observado uma relação entre as taxas de desgaste e o produto da carga crítica e a microdureza.

Aug 16, 2017

By William Rodrigues Soares

Este trabalho apresenta um estudo sobre a influência de diferentes ciclos de tratamentos térmicos sobre a microestrutura e propriedades mecânicas de dois aços (A e B) especificados pela norma API 5CT. O aço B tem um conteúdo de elementos de liga maior que o aço A. Caracterizou-se de forma qualitativa e quantitativa as microestruturas por meio de microscopia óptica e eletrônica de varredura. As propriedades mecânicas foram medidas por meio do ensaio de tração. As amostras do aço A submetidas ao resfriamento ao ar calmo e forçado apresentaram uma maior fração volumétrica do constituinte MA (martensita/austenita retida) em relação ao aço B e o aumento da taxa de resfriamento aumentou a quantidade de MA para os dois aços, o que resultou em um aumento no limite de resistência a tração para os aços A e B. As amostras que foram resfriadas ao ar calmo e ao ar forçado apresentaram menores limites de escoamento que as amostras temperadas e revenidas. Este resultado pode ser explicado pela presença de bainita e do constituinte MA nas amostras resfriadas ao ar calmo e ao ar forçado cuja presença gera uma maior densidade de discordâncias.

Aug 16, 2017

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017