Search Documents

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By C. S. Barrett, C. T. Haller

TWINNING in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study' concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: I. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation. 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. MATERIALS AND METHODS The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. [ ] X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on {102} planes causes a reorientation of the crystal lattice by 86°, it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallographic observation, for it was found

Jan 1, 1946

By Walter Renton, Ingalls

SEVERAL years ago I became interested in computing the historic lead production of the United States, and the mines, or mining districts whence derived. This led me subsequently to an examination of the recent records- of some of the American zinc-mining districts and of the great lead and zinc-mining districts in foreign countries. My present article thus will be to a large extent an addendum to my book, "World Survey of the Zinc Industry," which was published by the Mining and Metallurgical Society of America in 1931, and to which I shall refer hereinafter as Ingalls, op. cit. Throughout this article all expressions of tons mean the ton of 2000 lb. Where original data have been given in metric tons I have converted in many instances simply by multiplying by 1.1, and long tons by 1.12. I have not been fussy about digits and have rounded off many figures. These may explain differences between data herein and other data.

Jan 1, 1946

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

By Otto H. Henry, J. J. Cordiano

Though powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread" to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. Purpose of Investigation Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but ' such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: 1. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1946

By F. O., Garrabrant

ELECTRIC power requirements for Climax are similar to those of most metal mines, except that large blocks of power are used underground and there are a number of other unusual applications. Power is furnished to the Company by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are designed so that with the addition of forced cooling their capacity may be increased a third at 12,000-ft. altitude. On the secondary side of this bank is a 15-kv., 1200-amp. oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. (A more complete description of the electrical distribution system at Climax, with detailed drawings, is contained in T.P. 1734, A.I.M.E., Mining Technology, July, 1944.)

Jan 1, 1946

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

By J. H. Jacobs

This report records a chapter in the history of the development of an electrolytic manganese industry in the United States. Nearly all the manganese requirements of the United States have been imported. Although there are large quantities of manganese ore in the United States, most of it is low-grade and cannot be used for the production of ferromanganese. Since the electrolytic production of manganese carried out by a process developed in the laboratories of the Bureau of Mines offers a method whereby the extensive low-grade deposits may be utilized and since commercial development had proceeded slowly, the Bureau constructed a new and larger pilot plant at Boulder City, Nev., where abundant electric power was available. An authorization in November 1940 covered a plant of only several hundred pounds daily capacity. Additions to some sections author¬ized by subsequent appropriations have enabled the plant to produce over 2,000 pounds a day for extended periods.

Jan 1, 1946

8186. Aquilina, C. Determinazioni relative di gravita eseguite nel 1939 (Relative Determinations of Gravity Made in 1939), Ric. Ingegn, Rome, vol. 10, 1942, pp, 6376. In 1939, the author made a survey of relative gravity in the Mediterranean-basin, 41° 35,5' to 41° 56.3' northern latitude and 0° 10,3' to 0° 28' longitude, referred to Mt. Mario. Ten stations were covered; 25 other stations had been occupied in the vicinity of Rome and in Albanian mountains during previous years. The new measurements revealed gravity anomalies ranging within the following limits: (1) With a free-air reduction, between + 29 and + 120 mgl., average + 60 mgl.; and (2) with a Bouguer reduction, between + 22 and + 87 mgl., average + 41.5 mgl. - V. S.

Jan 1, 1946

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By A. Ross Rornmel

ABILITY to speak effectively is one of man's most longed for and coveted abilities. It is the ability to stand on one's feet, transfer knowledge and thoughts to others, to reach an objective professionally or otherwise by leading groups through a channel of planned thought. Each day group speaking plays an important part in making or marring success, and the engineering profession often provides this opportunity and requirement. An ability to speak effectively develops courage, poise, confidence, and prestige for the speaker. The technical man cannot be reluctant to face an audience. He is often called upon to do this in presence of employees, supervisors, and other groups. His ability to speak effectively is as much a requirement as the fundamentals of his profession. The three fundamentals of effective speaking are: (1) Enthusiasm and Confidence. These are joined because of their close relation. (2) Preparation. This includes knowledge of the subject. (3) Presentation. By this is meant the features of delivery.

Jan 1, 1946

By Oliver Bowles

WAR necessities have spurred inventive genius in many fields. A grinding mill without any moving grinding parts stirs the imagination. Among the new and striking accomplishments in the heterogeneous group of nonmetallic industrial minerals is the use of an electric arc to speed up manyfold the difficult and delicate task of drilling a microscopic hole in a diamond, the hardest of all known substances. Outstanding in the field of optical research is the ability that man has developed to improve upon nature by making in the laboratory optical crystals many times larger than those usually found in rocky crevices. These are merely samples of numerous events and circumstances of noteworthy import, many of which are recorded in this review. Termination of the second World War in 1945 permits an appraisal of the effects of the conflict and the probable effects of the coming restoration of a peacetime economy on the nonmetallic mineral industries. Some industries were stimulated greatly by the war, notably mica, quartz crystal, graphite, spinning asbestos, potash, fluorspar, barite, and refractories. The large-tonnage industries connected with the building trades, however, were forced to curtail their activities, except where their products were needed for wartime construction. Their reconversion to peacetime production will not be difficult.

Jan 1, 1946

By E. J. Eisenach, W. E. Jones

SAFETY and industrial hygiene have always been recognized as highly important in company policy, and the co-operative support of the company officials and entire plant personnel has contributed largely to the present success of the Company's program in this field. Growth has necessarily been slow, and dependent, at times, on trial and error but the program in its present form combines the regulations, working methods, and equipment that have proved their value under actual operating conditions. Every effort is made to keep the program on a practical basis. Continuous experimental work is carried on in conjunction with the health and safety program, with resultant periodic changes for improvement. As a proof of accomplishment, in 1945 the frequency and severity rates for accidents were the lowest in the history of the operation. A full-time safety engineer was employed in 1933 and an assistant safety engineer in 1936. During the following year a stenographer was employed in the office and a safety inspector was added for the mine. During the gradual expansion of operations that was climaxed by

Jan 1, 1946

By H. Stigzelius

FINLAND'S recent mining history is both dramatic and pitiful in its shifting fortunes, dominated as it has been, by the country's proximity to the border zone of opposing dictatorships and social traditions; Fascism to the south, Communism to the east, and Democracy to the west. After 108 years under Russia's more or less harsh rule, Finland gained its democratic independence during the 1917 revolutionary strife in Russia with the official help of Germany and spontaneous help of other neighbors. The young nation was attacked by Russia in 1939 and again in 1941. It is common knowledge how the Finns fought with everything they had and everything they could get against their overwhelming adversary, and how by force of circumstances they landed in the Axis camp in 1941. Finland has never been known as a mining country in the same way as near-by Sweden, whose abundant iron and copper smelters during long periods so greatly contributed to the nation's welfare. Its largely barren, Archaean-granite geology long seemed forbidding. Some mining was done, to be sure; copper and tin at Pitkaranta near the Russian border, and lead and copper at Orijarvi. But towards the end of the last century the absence of a single producing mine cast a pessimistic shadow of truth over the Finnish poet Runeberg's words, that

Jan 1, 1946

By L. S. Cates

THE war is now behind us. We in the mining industry feel a just pride in the part that our industry and our men and our products played in defeating the enemy on the fighting fronts around the world. In five years of mobilization and actual combat, our mines and oil wells produced over 3 billion tons of coal, a billion tons of petroleum, 500 million tons of iron ore, 21/4 million tons of lead, 31/2 million tons of zinc, 5 million tons of copper, 14 million tons of bauxite, 17 million tons of sulphur, 68 million tons of salt, and 3 million tons of potash. It was an unparalleled performance. But what of today? Why the present low production and high costs? Among the black clouds in the mining sky none are so black as that presented by the labor situation. We know it is the result of the legislation and the interpretation of that legislation in the past ten or fifteen years. Since the passage of the Norris-LaGuardia Act in 1932, we have had nothing but a succession of laws, regulations, and decisions that have intensified the strength of the unions and made the operators of the mines and the sources of their financing prartirally impotent

Jan 1, 1946

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

By George A. Miller

OIL, the abundance of it in the hands of the Allies and the lack of it in the hands of the Axis, played a major role in winning World War II. It bids fair to implement the winning of the peace. In fact the signing of the revised agreement on petroleum between the Government of the United Kingdom of Great Britain and Northern Ireland and the Government of the United States of America on Sept. 24, 1945, may be considered as the first step in establishing a new pattern in foreign relations by our Government. The significance of this agreement on petroleum is that it was arrived at on the part of the United States of America through the advice and consent of the most interested parties, the leaders of the petroleum industry and the Government, distinctly a first step toward unifying the power of business and the strength of the Government, which places us on a par with the British Crown which has always had the advice and counsel of its business leaders in formulating its foreign trade policies. And what is the thing so patently discernible in this new first step toward winning the peace? It is that the petroleum agreement, the first draft of which, signed in Washington on Aug. 8, 1944, almost caused an epidemic of apoplexy among the leaders of the oil industry, represents the desire of the people most concerned with the problems of petroleum both at home and abroad. This new agreement, which will come up before the Senate for ratification this month-hearings will commence in January - derives its "power from the consent of the governed," something about which our forefathers were vitally concerned once upon a time.

Jan 1, 1946

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946