Search Documents

By Byron E. Blair

This report describes procedures for using a high-speed camera to study blasting phenomena. Both quantitative and qualitative information can be obtained, provided that proper interpretations of the projected two-dimensional images are made. Geometrical relationships between object and image displacements are given in terms of horizontal and vertical angles of the camera optic axis with respect to the quarry face. Correction factors are given for obtaining true object displacements from image displacements in the camera film plane. The time of initial rock movement also is considered, and the control-ling factors of camera speed, scale factor, minimum increment of projection measurement, etc., are evaluated in terms of minimum time intervals. The high-speed camera and associated equipment are described, and field measurements and laboratory data analysis techniques are outlined. An analysis of a typical high-speed motion picture is made, and the application of the necessary correction factors is illustrated.

Jan 1, 1960

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By E. G. King

Strontium sulfide and barium sulfide occur as intermediates in commercial treatments of the impure natural sulfates to produce pure strontium and barium chemicals. Thermodynamic considerations involving these sulfides have been hampered by lack of basic data, such as the entropies at 298.15°K. This paper reports the results of heat capacity measurements of strontium sulfide and barium sulfide in the temperature range 50°-298°K. The entropies at 298.15°K. were derived from the heat capacity values. Free energies of formation at 298.15°k. were computed from the entropies and literature values of the heats of formation. Strontium sulfide and barium sulfide are thermo-dynamically less stable than calcium sulfide, but more stable than magnesium sulfide.

Jan 1, 1960

By J. B. Gayle

Oven widths for experimental and commercial slot-type ovens differ appreably in most instances; the experimental ovens usually ranging from 10 to 14 inches and the commercial units from 14 to 21 inches. Application of results obtained with experimental ovens to commercial practice thus requires major extrapolations. A critical survey of the literature indicated that sufficient information about the effects of variations in oven width on the carbonizing process is not available to permit such extrapolations to be made with any considerable degree of confidence.

Jan 1, 1960

By I. Iwasaki

In recent years the rapid depletion of high-grade iron ores and the demand by blast furnace operators for increasingly low-silica ores have stimulated interest in flotation studies of low-grade iron ores, such as wash-ore tailings and oxidized taconites. Four processes have been reported for the flotation separation of these iron ores--anionic and cationic collection of the iron oxides, cationic collection of siliceous gangue, and anionic collection of activated siliceous gangue (5).5/ The effectiveness of any one method, however, depends largely on the mineralogical composition and on the physical structure of the sample; hence, a comprehensive study of the floatability of the individual minerals occurring in these materials is essential. A review of the literature shows that the floatability of hematite and magnetite has been frequently investigated, whereas very little corresponding information is available for goethite, or for its more earthy form, limonite, both of which are abundant in the Mesabi and Cuyuna ores (19). The purpose of this investigation was to formulate general information on the floatability of goethite. Vacuum flotation, contact angle measurement, and simplified flotation tests using a modified Hallimond tube were used. The experimental results were correlated with the electrokinetic properties of goethite as determined by streaming potential measurement. The results were used to interpret the batch flotation tests made on an artificial mixture of quartz and goethite.

Jan 1, 1960

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

By D. C. Fleck

This report describes a method of using sodium for reducing titanium tetrachloride, developed at Boulder City, Nev., as part of the Federal Bureau of Mines effort to improve the extractive metallurgy of titanium. Finely divided titanium metal, titanium lower chlorides, or a mixture thereof was produced in a continuous operation at temperatures between 105° and 205° C. by the reaction of molten sodium and vaporized titanium tetra-chloride in an agitated bed of finely divided inert solids (powdered sodium chloride or the reaction products). Composition of the product was controlled by varying the relative quantities of sodium and titanium tetrachloride used. A description of the operations and analytical data of the reaction products are given.

Jan 1, 1960

By J. S. Berber

Bastnasite is a natural fluocarbonate of the cerium group and affords an abundant and high-grade source of the lighter rare-earth elements. As part of a broad research program in rare-earth element technology, the Federal Bureau of Mines directed extensive experimental work to separating and purifying the rare-earth elements in bastnasite. By the use of a combination of techniques--classical chemical, ion exchange, and solvent extraction--the processing of a bastnasite concentrate to obtain the individual rare-earth elements, or groups of elements, was accomplished. A bastnasite concentrate, containing about 60 percent rare-earth oxides, was sulfated with concentrated sulfuric acid to eliminate the carbon dioxide, fluorine, and silica. Calcination at 1,200° F. made the gangue matter insoluble, thus permitting the separation of the soluble rare-earth sulfates. Essentially 100 percent of the rare-earth elements were recovered by this procedure. Since the rare-earth sulfate solution contained only trace amounts of nonrare-earth elements, subsequent separation procedures were simplified.

Jan 1, 1960

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By D. D. Walker

Scheelite, the most abundant tungsten mineral in the Philipsburg region of Montana, is found in replacement deposits and along fissures and cracks in limestone at various distances from contacts with acidic igneous rocks. It also occurs at the limestone-igneous contacts, but typical garnet tactites are developed in only a few places in the region. The most favorable host rocks for scheelite mineralization are the Jefferson, Hasmark, and Madison limestones. Scheelite is exposed in float, outcrops, and surface and mine workings along a 2-mile-wide belt extending southwest from Lost Creek beyond Silver Lake, a distance of 15 miles or more. (See fig. 1.) Some scheelite is found in veins formerly mined for silver. Powellite and molybdenite occasionally are present with the scheelite. Hubnerite occurs in quartz veins in the Black Pine area 10 miles northwest of Philipsburg. These quartz veins occur in the quartzites of the Precambrian Spokane formation. Tungsten production in the region has come almost exclusively from scheelite deposits, both lode and placer. During a 6-year period beginning in 1943 a total of 142.0 tons of 63-percent W03 concentrate was produced by H & H Mines Co. In the early 1950's, the Trigger mine produced 4,000 tons of 1-percent W03 ore and the Tip Top 650 tons of 2.0-percent W03 ore and 2,906 tons of 2.2-percent ore. There has been sporadic production from some of the smaller properties in the area.

Jan 1, 1960

By John Nagy

A study was made in the Bureau of Mines experimental coal mine of factors affecting gas ignition by a cutoff explosive charge. Experiments showed that, although gas could be ignited under some circumstances, the probability under normal mining conditions would be low. The use of permissible explosives, relatively short-delay intervals in firing adjacent holes, blasting to a 6-inch kerf, and reasonable care in the placement of the holes favor safe blasting and are current practice in mining. The experiments also showed that the weight of the charge is not a primary factor in the ignition of gas by a cutoff charge. The quenching action of a first charge on the igniting action of a second was verified in a supplementary study. Related experiments have shown that gas at the face may be ignited by a single charge of explosive when fired with a light coal burden. Permissible explosives were less hazardous under these conditions than nonpermissible explosives. The frequency of gas ignition in cutoff and single-charge experiments increased as the linear distance between the sheared face and the opposing mine rib increased.

Jan 1, 1960

By John C. Holtz

"The Federal Bureau of Mines serves the mining industry by approving equipment that is designed to prevent explosion, fire, shock, or toxic hazards in mines when such equipment is used and maintained in a proper manner, through research, consultation, testing, and inspection, the Bureau studies machinery and component parts submitted by manufacturers and others. Before receiving the Bureau's approval as permissible for safe use in mines, equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's various permissibility schedules. An important phase of the Bureau's research is the testing of diesel engines.Mobile diesel-powered equipment can be used safely in underground noncoal mines and tunnels when mechanical ventilation is provided to dilute and remove the exhaust gas and to replenish oxygen in the underground atmosphere. Safe ventilation is determined by suitable tests of each engine used in a diesel machine. This ventilation cannot be predicted safely, accurately, and economically from any general empirical relationship.In determining safe ventilation, the quantities of carbon dioxide, carbon monoxide, and oxides of nitrogen generated by a diesel engine must be ascertained. These quantities are related to the displacement of the engine, its speed of operation, the design of the combustion chamber, and the fuel:air ratio needed to produce useful power. At overrich fuel:air ratios, all diesel engines generate excessive quantities of toxic carbon monoxide and smoke. The results of engine tests are used to determine a maximum fuel-injection rate at or below which carbon monoxide can be controlled by a reasonable ventilation and smoke is essentially eliminated. Toxic oxides of nitrogen are related to fuel:air ratio and the design of the combustion chamber. Their concentration in the exhaust cannot be controlled by engine adjustments, and each engine appears to have individual characteristics concerning formation of these oxides. Production of oxides of nitrogen frequently is the most important factor in determining safe ventilation."

Oct 1, 1959

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By Michael Sokaski, M. R. Geer, H. F. Yancey

This report is one of a series describing investigations by the Federal Bureau of Mines of the performance of various types of coal - cleaning equipment ; other reports in the series are listed in the bibliography . The information in these reports is useful to the coal industry and the manufacturers of coal - cleaning equipment in several ways : First , it assists the coalpreparation engineer who is planning a new plant to select the type of process best suited to the requirements by enabling him to forecast the yield and quality of clean coal obtainable with each type of equipment . Second , the information serves as a yardstick by which the performance of a plant can be judged and thus helps determine whether it is operating at satisfactory efficiency . Both these functions promote better coal - preparation practice ; that is , they help provide coal of more suitable quality for the market and likewise minimize the waste of good coal . This serves the interest of conservation with which the Bureau is vitally concerned . The present report deals with three plants using the Tromp dense - medium process , named after its inventor , K. F. Tromp , who developed the process in the Netherlands in 1936.5/ Selection of this particular dense -medium process for investigation was entirely a matter of convenience , and reports dealing with other dense -medium systems are planned for the future . Two baths are employed in one of the plants investigated . The first of these , handling 6- to 3 - inch coal , exhibited an exceptionally sharp separation between coal and impurity . This was characterized by an error area of 12 and a probable error of 0.023 . In the second bath , treating refuse from the

Jul 1, 1960

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960