Search Documents

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

By T. T. Read, T. L. Joseph, F. H. Royster

In a preliminary study of the beneficiation of iron ores conducted by the Bureau of Mines, one of the authors (T. T. Read) found it necessary to ascertain, if possible, how much effect a decrease in the silica content of an iron ore has upon the cost of making pig iron from the ore. In the beneficiation of iron ores the most important impurity to be removed is usually silica, and the amount that can be expended on a beneficiation process to reduce the silica content of the ore is obviously determined by the amount of increase in the value of the ore after beneficiation. The price that can actually be obtained for a beneficiated ore is, of course, a matter of negotiation between the seller and the buyer, but since the relative value of different grades of iron ore must be chiefly based upon the cost of making pig iron from them, an approximation as to the effect which decrease in the silica content of ore has upon the cost of snaking pig iron is an important guide in estimating what probable average gain will result from subjecting an ore to a beneficiation process. A search of the literature failed to reveal any detailed statement on this important topic, but fortunately the data are at hand to permit making an approximate calculation of the probable effect. For the purpose of the calculation assume three iron ores with the following composition (natural):

Jan 1, 1924

By F. C. Houghten, R. R. Sayers, C. P. Yalaglou

"Introduction.Atmospheric conditions relative to high temperature and humidity are of great importance in mining, as well as in such allied fields as railroad and vehicular tunnels. An extended investigation into the effect of these factors on men has been in progress for some time, both in the field under actual working conditions, and at the Pittsburgh experiment station of the bureau in cooperation with the American Society of Heating and Ventilating Engineers and the U. S. Public Health Service.For several years one of the writers (Dr. Sayers) and L. Harrington, supervising mining engineer of the bureau, have been studying the effects of hot humid atmosphere in metal mines on the comfort and efficiency of the workers. Some of the reactions experienced in still and in moving saturated mine air at temperatures of 90 to 100°F., with men at rest are presented in a recent paper.****The present paper is based on experiments made under carefully controlled conditions to determine the relative feeling of warmth experienced by men in atmospheres of various degrees of temperature and humidity. The work was conducted by the research laboratory of the American society of Heating and Ventilating Engineers, at the Pittsburgh experiment station of the Bureau of Mines, in special physchrometric chambers built for this purpose. It was carried on under the direction of F. Paul Anderson, director of the laboratory, Dr. R. R. Sayers and A. C. Fieldner of the Bureau of Mines. The results given in this paper are for still air only. Investigations of the effects of moving air are being continued, and will be reported later."

Jan 1, 1924

By W. W. Odell

"It is common knowledge that extensive lignite deposits occur in the States of Montana, North and South Dakota and Texas. The total area of these deposits and the total amount of lignite in them is so great that the true economic value of lignite is seldom realized. These deposits underlie areas of thousands of square miles. The area of the lignite lands in North Dakota alone is estimated to be approximately 32,000 square miles. Nearly one-third of the total solid-fuel resources of the United States is lignite and approximately 90 per cent of this lies in the Northwest.To the people of the Northwest the more extended utilization of lignite is of fundamental importance, hence any methods for commercially producing salable products from lignite that promise further development of these great fields deserve careful study.The development of our lignite resources has been slow, partly because the districts wherein lignite is found is not thickly settled or highly developed in manufacturing industries, but also because of the physical and chemical characteristics of the lignite. Lignite is classed as a low-grade fuel and may be con¬sidered as imperfectly developed coal -which has a more or less woody structure; it may be of the brown-coal type or darker, denser and more homogeneous, approaching subbituminous coal in character. As mined it contains more than 30 per cent of moisture exclusive of the -rater of decomposition formed .then it is carbonized or burned. The heating value as determined by the calorimeter is approximately half that of good quality bituminous coal. Upon exposure to the air lignite loses part of its moisture, whereupon the lumps chock and split until after considerable exposure, a large percentage of slack is formed. It cannot be stored in large piles so successfully as come other fuels, and it some instances it is more apt to ignite spontaneously in storage or in transit then the higher grade fuels."

Feb 1, 1924

By Byron M. Bird, Earl R. McMillan

"The method and apparatus described herein was developed at the Northwest experiment station of the Bureau of Mines, Interior Department, in cooperative research work with the University of Washington. A fuller description will appear in a bulletin entitled ""study of coal washing problems in the Pacific Northwest, to be published by the University. During the past four years this Bureau and the University have been co-operating with various coal companies in the Pacific Northwest in an extensive study of coal washing problems. Much of the valuable data resulting from this study has been obtained with the well-known float-and-sink test. This test has known for a number of years****, but its possibilities have not been thoroughly understood. A few investigations have developed apparatus and technique suitable to their needs, but these were not adopted to the conditions faced in the Northwest. Thus, the necessity arose for designing suitably equipment and working out a method of procedure or technique in carrying on the fundamental studies of coal washing by means of the float-and-sink test method."

Feb 1, 1924

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By N. A. C. Smith, D. D. Stark

"Sulphur is apparently a normal Constituent of crude petroleum, but in most crudes is present in percentages of less than one-half of one per cent. Some crudes, however, contain more, and occurrences have been reported of heavy asphaltic oils with as much as five per cent of sulphur.Occurrences of Sulpher-bearing CrudesIn North America, the fields rest of the Mississippi River are almost entirely free from sulphur oils, the time oil from Northern Ohio and Indiana, and the Potrolia crude in Ontario, being practically the only ones which contain sulohur in amounts over 0.5. per cent. In the Mid-Continent district the production of high sulphur crude in general is small and unim¬portant. The two main excentions are the Healdton field in Oklahoma and the El Dorado field in Arkansas, both of which produce oils with considerable sulphur content. In the Wyoming field, one sand, the Ember Sandstone, pro¬duces a crude of high sulphur content, and it is probable that this crude rill be of considerable importance as production increases. At present, however, very little crude is produced from this formation. In the Gulf Coast conditions are irregular, some crudes being low in sulphur and others comparatively high. The same is largely true of California. The crudes of Mexico contain notable amounts of sulphur, and as they have been of great commercial importance in this country, a typical sample of light Mexican crude was selected for the present study. It is probable that the results obtained poly also (but to a lesser degree) to other sulphur-bearing oils. An analysis of this crude will be found in Table 3, also analyses of other typical sulphur-bearing crudes from different sections of the United States."

Mar 1, 1924

By Oliver Bowles

"Underground operation.In its broader sense the term ""mining"" is applied to all processes whereby raw materials are taken from the earth to be used as sources of mineral products. In a more restricted sense ""mining"" is applied to underground operations as contrasted with open pit work designated as quarrying. The tern is used in the restricted tense in this paper; for it relates to the exploitation of limestone deposits by modern methods of underground operation rather than by open pit methods.Present tendency toward miningIt may seem to some readers that a paper on mining limestone will find little general interest among lime plant operators, for only a limited number of them have yet resorted to this means of procuring raw materials. It is noteworthy, however, that a growing tendency exists toward underground operation, for one by one quarry owners are faced with increasing difficulties in open pit operation. It seems desirable, therefore, for operators to keep closely in touch with this gradual change in process, to inquire into the underlying causes, to compare costs, and to study the effects of the change in method on subsequent steps in calcining the stone to produce lime."

Mar 1, 1924

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By D. A. Reynolds, A. C. Fieldner, S. H. Katz

"03-01-192403-31-2019RI 2591 - Reports of Investigations - Department of the Interior - Bureau of MinesBureau of MinesPittsburgh Experiment Station American Society of Heating and Ventilating EngineersU.S. Public Health ServicesTucson Experiment Station Introduction.""Carbon monoxide self-rescuers,"" or simply ""self-rescuers,"" are pocketsize gas respirators which protect the wearer from air contaminated with poisonous carbon monoxide gas. On March 6, 1924, the Bureau of Mines approved the ""M.S.A. self-rescuer’ manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa., after the M.S.A- self-rescuer bad passed all the tests and requirements of the Bureau's Schedule 14A4.The purpose of the self-rescuer is to help miners to escape from mines in which fires are burning or explosions have occurred, by providing protection from carbon monoxide for at least one half-hour. The self-rescuer can be used similarly by workers above ground who may through accident become surrounded or entrapped by atmospheres containing carbon monoxide.no hazards threaten the miner, who escapes serious injury by fire or violence in a large mine fire namely, ( 1) asphyxiation by poisonous carbon monoxide gas; and (2) suffocation by insufficient oxygen to support life. In order to save himself, the miner must either erect a barrica4e5 against afterdamp and wait restoration of ventilation and rescue or take a long chance at getting out of the mine through entries not permeated by afterdamp.. The self-rescuer removes the hazard of carbon monoxide poisoning for one half-hour or more, and accordingly greatly increases the miner's chance of saving his life.This paper describes the construction and details of the M.S.A. self-rescuer as approved by the Bureau of Mines, and discusses its performance under test condition"

Mar 1, 1924

By M. M. Myers

"Importance pf the small stone problem.Profitable disposal of limestone too small for making lime in the shaft kiln, is one of the most urgent problems in the lime industry. Reports received by the Bureau of Mines from 31 quarries show that the proportion of small stone varies from 2 to 40 per cent, averaging 18 per cent of gross pro¬duction, Modern methods of heavy blasting, and the use of crushers in large quarries tend to increase the proportion of small stone above that produced in early days when light blasting and hand sledging were almost universally used. There is also a growing movement toward underground operation of lime deposits, a method which in general produces a greater proportion of fines than is encountered in open-pit work. Thus the small stone problem is of growing importance, and demands the attention of every progressive lime producer. As the problem is of almost universal interest, it is urgently desired that every operator who reads this report will contribute from his knowledge or experience, answers to the questions on the final sheet.There are several markets in which small stone may be sold but in these markets the competition is generally keen and the prices low. The lime producer's chief product is lime, he understands its manufacture and marketing, and brings him a greater return than can be obtained from most limestone by-products. For these reasons it is evident that the conversion of small into lime is the nest desirable means of disposal."

Apr 1, 1924

By J. J. Jakosky

"This report is the second of a series dealing with electrical methods of underground communication nd signalling, and is a discussion of some of the factors involved in -applying radio in mines.A previous report2 described the results obtained by the use of the ""T.P.S."" of ground-conduction method of signalling, and outlined in a general way the requirements for a practical mine communication apparatus.The popularity of radio, the development work on new apparatus, a desire to render humanitarian service to entombed miners, and an endeavor to find new uses and applications for radio stimulated many persons to attempt the application of radio to mine rescue purposes. A number of experiments on underground reception from surface broadcast stations have been conducted by different experimenters in various parts of the country and the widespread interest in the subject is shown by the fact that these tests have been con¬ducted in many States, The Bureau of Mines has received information regarding, underground tests in Illinois, Pennsylvania, Arizona, Utah, Idaho, Colorado, Michigan, Wyoming, Kentucky, New York, Connecticut, and in England, Germany, Italy, and Franc.From occasional press notices and illustrations in different papers it may appear that radio communication in mines and in tunnels being excavated is en established fact, and that the method is comparatively simple. As a matter of fact the reverse is the case."

Apr 1, 1924

By George S. Rice, J. W. Paull, R. R. Sayers

"Standard rock dust for use in the rock dusting of coal mines might be defined tentatively as powdered mineral, light colored and free of carbonaceous matter and free silica, all of which will pass a 20-mesh screen while 50% of it will pass-through a 200-mesh screen.Such dust may be prepared from limestone, gypsum, anhydrite, or shale free of sand and flint. For the initial rock dusting of the average nongaseous bituminous mines enough standard rock dust should be applied so that the combustible content of the resulting mixture of rook dust with mine dust shall not exceed 45%, a range somewhere between 35% end 45% being the practical objective sought.All entries, slopes or passageways and room necks should be rock dusted.Additional safeguards are:a.,Rockdusting roomsb.,Scattering of dust in vicinity of shots before firing.c.,Placing of barriers in the mouths of panels, cross-entries and other key positions.Redusting becomes necessary whenever the combustible content of the mine dust exceeds the permissible maximum. This should be determined by regular, systematic sampling, followed by a simple analysis of the samples for combustible content. A Bureau of Mines volumeter for measuring the density can be used for the determination of combustible content."

May 1, 1924

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By A. W. Fahrenwald

"About two years ago the Bureau of Mines, Department of the Interior, and the University of Idaho undertook an investigation of classification in its relation to table concentration of Idaho ores. The cooperation of the management of the Bunker Hill & Sullivan Co. in placing at our disposal their West Mill and facilities as desired, offered an unusual opportunity for studying the field of hindered classification in its practical and economic relation to table concentration.It has been shorn theoretically, and demonstrated experimentally, that ore products are more easily and economically concentrated on tables if the natural feed, consisting of various minerals and of all sizes of particles of each mineral, be classified or grouped into a series of products in which the mineral particles of greatest density are small in diameter relative to the diameter of the mineral particles of lesser density. Products in which the maximum difference in diameter of light and heavy minerals occurs are to be obtained only by true hindered settling classification. To our knowledge there has never been a really good hindered settling classifier used in practice and the present tendency seems to be to by-pass any attempt at such classification.After a careful study of the nature of hindered classification and of the requirements for hindered settling in practice, a classifier has been developed that takes fullest practical advantage of the widely known, but generally only meagerly understood, condition of hindered settling so well analyzed a number of years ago by Dr. Richards.The present paper presents briefly some of the more important practical results accruing through the investigation."

Jun 1, 1924

By J. W. Faul

[The Bureau of Mines initiated an extensive research on coal-mine ventilation factors in 1922, large- scale tests being conducted in its experimental nine near Bruceton, Pa., over a period of two years. A comprehensive report an this work is in course of preparation, but in order to place the practical results before the mining fraternity immediately and in condenses form, the more important features will be presented in a number of short papers. The present report is the first of a series dealing with the resistance of coal-mine entries to the flow of air and considers only entries in which there are no obstructions other than the natural roughness of the ribs, roof, and floor.]

Jan 1, 1924

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By E. G. Meiter, S. H. Katz

"Railroad locomotives produce heat, gas, and smoke, which cause considerable discomfort to engine men and firemen while passing through tunnels. In order to try and improve these conditions, the Bureau of Mines has investigated the composition of atmospheres in cabs of freight locomotives while in tunnels; and some of the higher temperatures in the cabs were noted; physiological effects upon men were determined and gas masks and respirators were devised to eliminate the effects of irritating and poisonous gases and smoke. Those investigations were conducted in tunnels of the Baltimore & Ohio, Pennsylvania, and Union Pacific railroads; while that described in this paper was carried out in tunnels of the Chesapeake & Ohio, Railroad, situated in the Blue Ridge and Allegheny Mountains in Virginia and West Virginia, Freight locomotives used by this railroad are of the Mallet type, which have two separate cylinders: and two separate sets of driving wheels on each side. In locomotive language they are of the 2-6-6-2 type. All of the cylinders act as simple engines when starting or in slow, heavy hauling; but at faster speeds the pair of cylinders on each side operate compound, Mallet locomotives are the largest and most powerful now operated.The tendency in train operation has always been to increase the burden upon locomotives, Present traffic needs frequently load even the Mallet engine to capacity, and yet the weight of trains tends to increase. It has been suggested as a means of securing greater power units that Mallets be constructed to operate only as simple engines. This would increase the amount of steam given off as the amount of coal burned and the resulting volume of flue gas emitted."

Jul 1, 1924

By G. A. Bole

"This paper presents a review of the literature and is an epitome of work acne and articles published by Schurecht, Robson and Andrews', in the investigation of the feasibility of making basic refractories from dolomite, was carried on successively by these men, at the Ceramic experiment Station of the Bureau of Mines, Columbus, Ohio.Scope of the work.The dolomite refractories investigation of the Ceramic Station includes a study of the many fluxes which could be used to aid in the dead-burning of dolomite and also a complete survey of the iron oxide-alumina-silica field as fluxes. The temperature of calcination and the resulting properties have been carefully investigated, and the most desirable calcines chosen for further investigation in the making of dolamite bricks. Many binders and the several methods in common use of fabricating bricks commercially were tried, and a thorough study was made of the properties of the most successful ware,Previous Investigators.Even before the World War, considerable work was done on dolomite this war greatly accelerated the efforts of the many Investigators."

Jul 1, 1924