Search Documents

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By AIME AIME

TO THE AMERICAN MINING CONGRESS. AMERICAN INSTITUTE OE MINING ENGINEERS. MINING AND METALLURGICAL SOCIETY OF AMERICA. The committee that makes this report was appointed at the meeting of the American Mining Congress, at Denver, Colo., in. November, 1906. The appointment had in view the drafting. of a law for the regulation of quarrying and metalliferous mining under the police laws of the States, with the hope that the uniform adoption of such a law could tend to reduce the number of accidents in mining. Since its. appointment, the committee has had' under serious and continuous consideration the matter with which it was charged. At the meetings 0f the American Mining Congress in 19o7, 1908 and 1909, it reported progress. At the meeting in 1909 it was authorized to present its report not only to the American Mining Congress, but also to the American Institute of Mining Engineers and the. Mining and Metallurgical Society of America, and to present its report in printed form during the interim between meetings of the American Mining Congress. The committee collected from the officials of the States of the Union copies of their mining laws. With the assistance of the Engineering and Mining Journal copies of the laws 0f Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New aland, and certain European countries were also obtained. These laws were subjected to careful study. The first publication of the committee was a summary of the more important metalliferous mining laws 0f this country. Upon the basis of the existing laws of the States of the Union, Great Britain, and the English speaking colonies, a tentative draft. was prepared and printed in limited number in 1909, for convenience in securing the advice and criticism of a considerable number 0f persons engaged in the mining industry. In this way valuable suggestions were received. At the request of the chairman of this committee, Mr. Frederick L. Hoffman, statistician of the Prudential Insurance Company, of Newark, N. J., summarized and reviewed the available statistics of fatalities in metalliferous mining in the United States. Mr. Hoffman's report was published in the Engineering and Mining

Jan 10, 1910

By A T. Spathis

The 11th International Symposium on Rock Fragmentation by Blasting (FRAGBLAST 11) was held in Sydney, Australia, between 24-26 August, 2015. The 93 papers, including six keynote presentations, covered exciting and practical topics in 20 sessions within 12 themes. Just fewer than 300 delegates from 27 countries attended. Four workshops were conducted on the weekend prior to the symposium, with three field visits after the symposium to Sydney region quarries, the Hunter Valley coal mining region, and the Kalgoorlie gold mining region. Delegates had the opportunity to visit the exhibition areas that showcased the latest products, software, hardware and systems in blasting technology. The keynote addresses were held in plenary sessions and set the tone for the parallel sessions that followed. They spanned the dynamics of the mining industry, the detonics of explosives, the interaction of stress waves and fracture mechanics in fragmentation, wall control blasting, and the importance of education and engineering for full process optimisation.

Jan 1, 2015

By R. G. K. Morrison

By arrangement between the Ontario Mining Association and Messrs. John Taylor & Sons, Mining Engineers, 6 Queen Street Place, London, E.C.4, the writer was engaged for a period of not more than three months to report on the rockburst situation in Ontario mines. This was later amplified, by mutual agreement, to include, at the expense of detail, visits to the larger camps where rockbursts had not occurred, to get a general picture of conditions and to discuss the subject with operators in their respective areas. Scope of Activities Visits were paid to the following properties for the purpose of enquiry and discussion; the underground workings of those mines marked with an asterisk were visited on one or more occasions: KIRKLAND LAKE * Macassa Mines, Limited * Kirkland Lake Gold Mining Co., Ltd. * Teck-Hughes Gold Mines, Limited * Lake Shore Mines, Limited * Wright-Hargreaves Mines, Limited Sylvanite Gold Mines, Limited Toburn Gold Mines, Limited EAST KIRKLAND & LARDER LAKE Upper Canada Mines, Limited Chesterville Larder Lake Gold Mtng Co., Ltd. Kerr-Addison Gold Mines, Limited Omega Gold Mines, Limited PORCUPINE * Hollinger Consolidated Gold Mines, Ltd. * Mcintyre Porcupine Mines, Limited * Dome Mines, Limited * Buffalo Ankerite Gold Mines, Limited Paymaster Consolidated Mines, Limited Preston East Dome Mines, Limited Pamour Porcupine Mines, Limited Broulan Porcupine Mines, Limited Hallnor Mines, Limited Naybob Gold Mines, Limited Delnite Mines, Limited Moneta Porcupine Mines, Limited DeSantis Porcupine Mines, Limited Coniaurum Mines, Limited SUDURY lnternational Nickel Co. of Can., Ltd. * Falconbridge Nickel Mines, Limited LITTLE LONG LAC AREA * Little Long Lac Gold Mines, Limited MacLeod-Cockshutt Gold Mines, Ltd. Hard Rock Gold Mines, Limited Bankfield Consolidated Mines, Limited Magnet Consolidated Mines (1936), Ltd. à PICKLE LAKE AREA * Central Patricia Gold Mines, Limited * Pickle Crow Gold Mines, Limited UCHI LAKE * Uchi Gold Mines, Limited McKENZIE ISLAND AREA Gold Eagle Gold Mines, Limited * McKenzie Red Lake Gold Mines, Ltd. * Cochenour Willans Gold Mines, Limited RED LAKE * Howey Gold Mines, Limited Hasaga Gold Mines, Limited Madson Red Lake Gold Mines, Limited

Jan 1, 1942

By R. S. Dean

As set forth in the decision of the Trail Smelter Arbitral Tribunal, dated April 16, 1938 This Tribunal is constituted under and its powers are derived from and limited by the convention between the United States of America and the Dominion of Canada signed at Ottawa, April 15, 1935, duly ratified by the two parties and ratification exchanged at Ottawa, August 3, 1935 (hereinafter termed "the Convention") . . . The duty imposed upon the Tribunal by the Convention was to "finally decide" the following questions: (1) Whether damage caused by the Trail Smelter in the State of Washington has occurred since the first day of January 1932, and, if so, what indemnity should be paid therefor? (2) In the event of the answer to the first part of the preceding Question being in the affirmative, whether the Trail Smelter should be required to refrain from causing damage in the State of Washington in the future and, if so, to what extent? (3) In the light of the answer to the preceding Question, what measures or regime, if any, should be adopted or maintained by the Trail Smelter? (4) What indemnity or compensation, if any, should be paid on account of any decision or decisions rendered by the Tribunal pursuant to the next two preceding Questions? In this decision reported to the Government of the United States of America and to the Government of the Dominion of Canada, the Tribunal answered the first question in its entirety and reserved decision on the other three questions in accordance with the following extract from their decision

Jan 1, 1944

By AIME AIME

T HE Board of Directors of the A. I. M. E. held a meeting at Institute headquarters on Jan. 28, 1921. There were present 10 directors and 14 guests, the secretary and the assistant secretary. The following actions of the Executive and Finance Committees were approved: Wilkes-Barre Meeting, Sept. 12 to 17, 1921; authorization of Oregon Section; authorization of Upper Peninsula Section; appointment of Philip W. Henry and Thomas H. Leggett on special committee on Code of Ethics; and presentation of five copies of Raymond Memorial Volume to T. A. Rickard, who edited it. The By-Laws of the Ohio Section were approved. The resolutions in reference to the payment of certain contributions and assessments to the Library Board of the United Engineering Societies, adopted by the Board of Directors on June 27, 1919, were rescinded, and the resolution adopted that the income of the James Douglas Trust of $100,000 be paid over to the Library or otherwise applied by it for the purpose of maintaining the Scientific Library of this Institute in such manner as may be deemed advisable in furtherance of the purposes of such trust, and that said income shall be paid on account of and included in. the assessment levied by the United Engineering Societies on the Institute for the maintenance of the joint libraries of the Founder Societies.

Jan 1, 1921

By AIME AIME

QUALITY and size do not ordinarily go hand in hand, but there is good evidence that both these attributes reached a new peak at the Annual Meeting of the Institute in New York just concluded. Certainly, the total attendance of 2500 was far above any yet attained, as might be expected with the recent rapid growth of Institute member- ship. General comment indicates that the quality of the papers also was notable, though not measurable by so definite a yardstick as attendance. During the meeting 49 technical sessions were held, at which more than 250 formal papers were presented. In addition, there were some thirty special meetings of committees, Divisions, and other Institute groups. In reporting the Annual Meeting eleven years ago the statement was made that "unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger," and "the fifth floor, where a buffet lunch is served each day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size." Unfortunately the angel to succeed Andrew Carnegie, who financed the building of the present home of the Institute 35 years ago, has not yet ' appeared. Even if some one would merely build another elevator or two in the present building it would help. Fortunately, the modern auditorium of the American Radiator & Standard

Jan 1, 1940

By Milton E. Wadsworth, T. D. Chatwin

Bulk density variations can usually be minimized by properly mixing the material before moisture measurement. The measuring of moisture on material being with- drawn directly from storage bins requires some form of bulk density correction. In Bethlehem's pellet plants continuous automatic bulk density correction and uniform feed-rate control are obtained with Bethlehem's patented Bin Level Control System. With this sys- tem a single probe, suspended or inserted in the bin, senses whether material is at the proper level in the bin and automatically regulates filter speed to control the filter-cake discharge rate to maintain this level. The level of concentrate in the filter-cake bin can thereby be controlled to within ± 1/2 in. of the point of contact between the concentrate and the probe. Material thickness on the conveyor does not have to be controlled accurately and mix compositions can vary widely as long as they do not contain variable amounts of water-soluble electrolytes. In sinter plants, errors caused by changes in normal feed rate and bed height are minimized by counter-weights that permit the free-floating to maintain a uniform contact pressure on the mix. Large changes in mix resistance can be taken care of either by resetting the control point or by adjusting the calibration control.

Jan 9, 1968

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By Walter E. Mingramm

THE construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquified air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the' difficulty and cost of keeping on hand a large quantity of liquified air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found employment in all the devices now in practical use, is that in which the air contained in the human lungs at the beginning of the work is regenerated by the apparatus. By means of chemicals, such as caustic potash and caustic soda, the carbonic acid gas, CO., exhaled is absorbed, and the oxygen that has been consumed is replaced from a tank containing this gas under high pressure. The pressure of the oxygen (which is 1,875 lb. in the two cylinders at the beginning of the work) is automatically reduced to 75 lb., and is sufficient to keep the air inside of the apparatus in constant circulation, and to force it to pass through the chemicals provided for the absorption of the CO, gas. In the attempt to construct an apparatus which would (1) furnish the wearer with a sufficient supply of air; (2) replace the amount of oxygen used up by the lungs during the time of

Jan 7, 1908

By Morris Muskat

It is pointed out that the application of capillary pressure curves obtained by drainage or desaturation processes to the calculation of the fluid distribution in interphase transition zones involves a number of difficulties; namely: (I) the development of very low nonwetting phase saturations appears to be in contradiction with the lack of mobility of such distributions indicated by permeability-saturation curves, (2) dispersed nonwetting phases are thermodynamically unstable, and (3) discontinuous phases should not be subject to hydrostatic equilibrium requirements. While these difficulties could be obviated by assuming that the capillary pressure drainage curve has an initial horizontal segment, they are automatically circumvented by application of the imbibition capillary pressure curve to the lower part of the water-oil transition zone. These generally show zero displacement pressure at only partial wetting-phase saturations. The countercurrent upward flow of oil into the main oil-saturated pay and downward drainage of water also suggests that wetting phase imbibition processes will control the saturation distribution immediately above the water-saturated section. Similar considerations, with a generalized interpretation of the apparent wetting-phase behavior of the oil and gas phases, provides a basis for constructing the curve for fluid distribution in the oil-gas transition zone. In the transition zones so derived, the oil begins with a nonvanishing saturation at the water-oil contact and terminates with a similar saturation at the top of the gas-oil contact. The gas-oil transition zone begins with an equivalent nonvanishing gas saturation. Introduction It has been a common assumption for some years that the nature of the fluid dis- tribution in virgin reservoirs, and in particular that in the transition zones between the oil and water and between the oil and gas sections, can be computed by a simple application of capillary pressure data. The results of such calculations appear to have been first reported by Leverett.' The latter, however, indicated only the numerical values of the parameters used in the computations, without explicitly describing the procedure. Leverett's illustrative calculated transition zones are reproduced in Fig I. Although no critical study of the apparently obvious method of calculation has been published, one cannot proceed very far in the computation without encountering some rather fundamental questions not yet answered in the literature. This paper is not written under the pretense that the whole transition-zone problem has been fully and satisfactorily solved. Its purpose, rather, is to discuss suggestions for its treatment, much of it admittedly hypothetical, and emphasize the nature of the uncertainties arising therein; for the literature, as now available, gives little indication that there are any problems still outstanding. The Transition-zone Equation The basic equation, which presumably gives directly the fluid distribution without recourse to any further consideration, is: Ap = (r1 - r2)gh [1] where r1, y2 are the densities of the two contiguous fluids, h is the height above the "capillary-free" zone of complete saturation with fluid I, g the acceleration of gravity, and Ap is the capillary pressure across the average interface at the height

Jan 1, 1949

By Zhiwei Jiao, Ziqing Guo, Mushen Wang, Yueda Fang, Qiuming Tang

In order to achieve anti-terrorism, production safety, better explosive performance, lower cost, and environment protection, we developed HMS (emulsification in borehole).Long-process PM (plant-mixed) and SM (site-mixed) emulsion trucks are reviewed and compared to a new type of short-process HM (hole-mixed) truck for onsite emulsion manufacturing. The short-process HM truck has demonstrated many advantages over its PM and SM counterparts in areas such as process safety and security, energy efficiency and environmental impacts: 1) No emulsion matrix is manufactured in the plant, transported on public roads, or even present on the surfaces of blasting job sites. Such characteristics are certainly beneficial in eliminating risks of the product being diverted and used by unlawful players; 2) This short-process involves "micro-fluid control to form super oil phase-rich" in tubular emulsification process, making it intrinsically safe; 3) There is basically no residual matrix left in the truck or on the job site to clean up, which greatly reduces environmental impact of the process; 4) Comparing with typical PM and SM trucks, the HM truck has eliminated the needs of many power equipment and critical pump pressure for turbulent flow forming a static emulsification with super oil phase -rich is only 0.2Mpa. These is therefore quite energy efficient.

Feb 1, 2020

By S Wangchai, D B. Hastie, P W. Wypych, A P. Grima

Industries that handle and process ‘dusty’ ores are facing increasingly difficult challenges to ensure sustainable operation and development. Most existing dust-control measures treat only the symptoms of dust generation and do not deal with the root cause/s of the problem. Many of these methods are also relatively inefficient in terms of controlling dust emissions. This paper summarises the various existing options available for dust control and some of their features, advantages and disadvantages. It then describes some of the new technologies that are being researched, developed and employed to minimise dust emissions by addressing dustability or dustiness and the dust generation mechanisms found in industry. Recent research results and case studies are presented to demonstrate some interesting findings obtained from this work. With improved understanding and modelling of dust generation mechanisms and bulk material dustiness, it is possible to achieve a step-change improvement in the design, troubleshooting and application of more efficient dust-control technologies.CITATION:Wypych, P W, Hastie, D B, Wangchai, S and Grima, A P, 2015. Research and application of new dust control technologies for the iron ore industry, in Proceedings Iron Ore 2015, pp 529–536 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By Plato Malozemoff

While this conference is dedicated to the examination of "Challenges in Mineral Processing," the broader aspect of the pursuit of this subject is Research and Development in the Mining Industry. When I was asked to speak at this symposium, I hesitated to accept. While my early schooling, training and professional occupation were in the field of this symposium, it was so long ago that I no longer feel competent to contribute anything of interest to you except perhaps for a limited historical perspective, which most of you probably already know. However, it might be worthwhile to explore the more general aspect of research and development from the viewpoint of management, as this is the stance from which I dealt with the subject for the last 30 years or so. While most managements generally have a positive view of research and development, few of the leaders in the mineral industry have actually had the personal experience of doing research for a long enough time to have obtained a full understanding and the feel for its place in the long-term technological innovation that our industry must foster. I graduated from the University of California in Berkeley with a Bachelor of Science degree and a major in metallurgy. It was during the great depression of the thirties, and it was difficult to obtain a practical job in the industry. I got a scholarship at the Montana School of Mines and received a Master of Science degree in ore dressing under Professor A. M. Gaudin, followed by another year with him pursuing research. Anyone who studied under him, or knew him well, would assert that this was a unique experience. Gaudin had a brilliant mind and a profound respect for science and the scientific method. He wished to know the scientific basis for every new technological appli-

Jan 1, 1989

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By Hinchliffe WD, Griffin A

The desorption of gold from activated carbon is promoted by adding organic solvents to aqueous cyanide solutions. At 65-80¦ the elution of gold is fast and is not affected by water quality. The Micron Procedure involves pretreatment of the loaded carbon with NaCN/NaOH followed by elution with methanol vapour and condensate. Carbon is packed into a column above the distillation pot and acts as a fractionating column. Recovery of the methanol condensate leaves a methanol free concentrated gold solution and carbon containing

Jan 1, 1984