Search Documents

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By R. C. Gould, A. M. Skov, L. F. Elkins

Comparison of long term decline in oil production during cyclic waterflooding or pressure pulsing of part of the Driver Unit with steady injection-imbibition flooding in the Tex Harvey area led to large expansion of flood in the Driver Unit on the steady injection basis. While the flood has been successful, the major problem has been attainment of satisfactory oil production rates in most of the wells. Large volume fracture treatments of low capacity wells were unsuccessful in achieving sustained increases in production. A two-section area in the Driver Unit has already recovered 620 bbl of oil per acre by waterflood but other areas have not performed so well. Sun Andres water containing 300 to 500 ppm H,S is sweetened to 0.5 to 1 ppm H,S by extraction with oxygen-free flue gas. This prevents contamination of gas produced in the area and apparently it has reduced corrosion in minimum investment, thin-wall, cement-lined water dktribution systems. Cement-lined tubing in injection wells has mitigated corrosion as effectively as thick polyvinyl chloride films have, and at less cost. Introduction As reported in the literature the Spraberry field of West Texas has presented unusual problems for both primary production and waterflood ing. Earlier information from the Spraberry Driver Unit included conception and evaluation of cyclic waterflooding or pressure pulsing in a nine-section pilot test as an aid to extraction of oil from the tight matrix rock and as a boost to normal capillary imbibition forces An additional 5 years' operation in that area, and performance of expanded steady injection water-flood, now covering a total of 68 sq miles, are reported herein. In addition, since the Driver Unit is one of the largest waterfloods in areal extent in the U. S., many operating experiences are presented for the benefit of engineers concerned with operation of other Spraberry floods or with other waterfloods where this reservoir technology and/or water handling technology may be adaptable in part. These include: (1) attempts to improve producing well capacity through large volume fracture treatments, (2) long-term performance of water treating plants utilizing oxygen-free flue gas to extract H,S from sour San Andres water, (3) performance of thin-wall cement-lined pipe in water distribution systems including comparison between those sections carrying raw San Andres water and those carrying treated water, and (4) comparison of performance of various lining materials and subsurface equipment in water supply and water injection wells. These experiences are reported without regard to whether results are good, bad or indifferent. Since the operations reported are limited to the techniques, materials, and equipment actually used in the Driver Unit, no comparison is possible with results of other approaches used in other Spraberry floods or in waterfloods generally under different conditions. However, an attempt is made to quantify these experiences as much as possible in the space available to permit other engineers to select those parts applicable to eheir problems. Background The Spraberry, discovered in Feb., 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members—a 10- to 15-ft sand near the top and a 10- to 15-ft sand near the base, having permeabilities of 1 md or less and porosities of 8 to 15 percent. Extensive interconnected vertical fractures permitted recovery of oil on 160-acre spacing from this fractional-millidarcy sandstone, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 percent of oil in place, with most wells declining to oil production of a few barrels per day when reservoir pressures are still in the range of 400 to 1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low production rates at these relatively high reservoir pressures. In 1952 Brownscombe and Dyes proposed that displacement of oil by capillary imbibition of water from the fractures into the matrix rock might significantly increase oil recovery from the Spraberry, overcoming otherwise serious channelling of water through the fractures." A pilot test conducted by the Atlantic Refining Co. during 1952 through 1955 indicated technical feasibility of the process; but low oil production rates averaging I5 to 20 bbl/well/D failed to create significant interest in large-scale waterflooding at that time." Humble Oil & Refining Co. conducted a highly successful 80-acre pilot test during 1955 through 1958 with

Jan 1, 1969

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By N. Mungan

Formation damage, i.e.. reduclion in permeability, has been generally attribuled to clay minerals which expand or disperse upon contact with water that is less saline than the connate water. Luboratory, studies show that penneahility reduction can also occur in formalions containing only nonexpandable clays such as illite or kaolinite, and can be caused also by changes in pH. Furthermore, pH changes can damage even formations that are essentially free of clays. It is suggested that permeability reduction is due to the small passages being blocked by particles, which may be dispersed clays, cemenlion material or other fine parricles. These particles are dislodged by dispersion of clays due to changes in salinity or by dissolution of calcareous cement by acids, or of silicaceous cement by alkaline solutions. In working with reservoir cores, it was found that extracted cores damaged more easily and extensively than nonextracted cores. The extent of damage depended also on tenlperatltre. INTRODUCTION Permeability is an important property of porous media and has been the subject of many studies by engineers and geologists. Many of these studies are conccrned with formation damage, i.e., reduction in permeability, resulting from exposure of oil-producing formations to water substantially less saline than the connate water. This effect causes understandable concern since during drilling, completion and production phases formations are often exposed to fresh water. The damage resulting from contact with relatively fresh water has been attributed to expansion and dispersion oF clay minerals. During laboratory investigation of the use of NaOH as a wettability reversal agent to increase oil recovery from oil-wet reservoirs, several cores used in the displacement studies suffered loss in permeability. Despite the traditional usage of NaOH for conditioning aqueous mud systems, the role of the caustic filtrate in wellbore damage seems to have been overlooked. Browning2 as recently reported on the effects of NaOH in dispersing clay minerals but he was concerned only with complications that may arise in drilling massive shale beds. The following study was made to examine the role of pH and salinity changes in core damage. Where cores from reservoirs were used, tests were performed with extracted and nonextracted cores both at room and reser- voir temperatures, since it was felt that the test environment and core condition may affect the results. Because of its limited coverage and exploratory nature, this study is not intended to provide answers to field formation damage problems. It is hoped that it will encourage research into new aspects of the permeability reduction problems, particularly those allied to new recovery and production processes. PROCEDURE In all permeability tests, fluids were pumped through the cores at a constant volumetric rate. Only deaerated fluids and reagent grade chemicals were used. The fluids were passed through two ultrafine filters before injection to remove any entrained particles. The cores, with the exception of the unconsolidated cores, were mounted in Hassler holders. Water was used to transmit pressure to the sleeve. The inlet endpiece had two entry ports which permitted scavenging one fluid with another to avoid any mixing in the small holdup volume. The cores were flushed with CO2 gas, evacuated for 5 to 6 hours and saturated with the first liquid at a pressure of 1,000 psi for 24 hours to eliminate any free gas from the cores. Pressure differences up to 20 psi were measured by transducers, calibrated in inches of water and continuously recorded. For greater pressure drops, gauges were used. All reservoir cores were cleaned with a light refined mineral oil, then with heptane, and finally dried with CO2. Compatibility tests showed that no precipitates formed when mineral oil and the crudes were mixed. Some cores were extracted in Dean-Stark-type solvent extractors using xylene and trichloroethane and dried in a vacuum oven at 450F. Each test consisted of a sequence of water, test solution, and again water flow. RESULTS AND DISCUSSION STUDIES IN BEREA CORES Salinity Contrast Berea cores 2-in. in diameter and 12-in. long were cut from sandstone quarried in Cleveland, Ohio. The clay minerals were identified by X-ray diffraction to be chlorite, kaolinite, illite and incerlayered illite. Flow of fresh water or 30,000 ppm brinc does not cause any permeability reduction (Fig. 1). However, after injection of brine the core is readily damaged by fresh water. Damage starts almost instantly as the fresh water injection is begun, and at a cumulative injection of 1.2 PV fresh water, the permeability has dropped from 190 to 0.9 md. Upon continued injection, the effluent contains clay minerals dislodged from the core. The final core per-

Jan 1, 1966

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By J. S. Rinehart, W. C. Maurer

The mechanics of impact crater formation in rock, particularly sandstone, has been sutdied, the velocity range being approximately that normally associated with oilwell gun perforators. The bullets were small steel spheres having diameters of 3/16, 9/32 and 7/16 in; impact velocities ranged from 300 to 7,000 ft/sec. The craters have two distinct parts — a cylindrical hole (or burrow) with a diameter the same as that of the impacting sphere, and a wide-angle cup comprising most of the volume of the crater. The burrow is fornred as material in front of the projectile is crushed and pushed aside, forming a cylindrical hole surrounded by a high-density zone. The clip forms as fractures are initiated in front of the projectile and propagate along logarithmic spirals, approximaling maximum shear trajectories, to the free surface of the rock. A most significant observation (made for the first time) was that, below the base of the cup in one type of sandstone, there are a group of similar fractures, not extending to the surface, which are spaced uniformly a few millimeters apart. Each fracture follows roughly the contour of the base of the cup and appears to require a certain threshold impulse to initiate it. These fractures comprise a relatively high fraction of the total, newly exposed surface area. The volume of the material removed by crushing varies as the first power of the impact velocity and the volume removed by fracturing, as the second power of the impact velocity. Penetration varies linearly with the impact velocity and is inversely proportional to the specific acoustic resistance of the target material, the proportionality constant being dependent upon the shape of the projectile. INTRODUCTION Yield of oil from a producing well is frequently enhanced by firing bullets and shaped charges through the well casing into the oil-bearing rock, forming craters and fractures from which oil can flow more readily. The purpose of this investigation has been to develop a better understanding of the mechanics of impact crater formation in rock, particularly sandstone, the velocity range being approximately that normally associated with oilwell gun perforators. FORCES OPERATIVE DURING IMPACT When a projectile moving at considerable velocity strikes a- massive target such as oil-bearing sandstone, intense and complex transient stress situations develop within both the projectile and the rock or sandstone against which it is striking. Usually the struck rock fails, the missile or projectile penetrating into the rock to some depth where it comes to rest or is forcibly ejected from its burrow by expansion of a plug of target material compressed in front of it. When the impact velocity is very high, the projectile itself may fail, breaking apart or becoming distorted; this situation is not considered here, the discussion being limited to nondeforming projectiles. Many experimental studies'.' have been carried out to determine the nature of the mechanics of crater formation and the salient features of the forces coming into play, some of the earliest studies being the French Army experiments performed at Metz between 1835 and 1845.' The stratagem in most instances has been to make a post-mortem examination of the crater, measuring volume and depth of penetration and deducing force relationships from these observations rather than performing the more difficult (usually almost impossible) feat of measuring stresses during penetration. In many materials, the force acting during penetration of the projectile is found to be the sum of two components—(1) a constant force, independent of the velocity, representing some inherent strength of the target material; and (2) a component, proportional to the square of the velocity, representing inertial forces. For such materials, the average force per unit area acting on the projectile at any instant while it is in motion and being decelerated may be written F/A = a + bv2 . . . (1) where v is the velocity of the projectile at that instant, A is the cross-sectional area of the penetrating projectile taken normal to its trajectory, and a and b are constants which are dependent upon the target material and the shape of the projectile. It follows that the total penetration s is given by .........(2) where v, is the velocity of the projectile when it just strikes the target. Values of a and b for spherical projectiles impacting in a loose sand-gravel mixture and compacted earth were obtained in the Metz experiments. For sand-gravel, a and b are 620 psi and 0.0115 (psi) (ft/sec)', respectively; and for compacted earthworks, a and b are 432 psi and 0.0008 (psi) (ft/sec)'. Figs 1 and 2

By A. Lubinski, J. L. Logan, W. S. Althouse

A4ost gas twells and flowing oil wells are completed and treated through a string of tubing and a packer. Changes in temperature and in pressure inside or outside the tubing will: (I) if free motion of the tubing inside the packer is permitted, increase or decrease the length of the rubing; or (2) if free motion is prevented, induce forces in the tubing and on the packer. If pressure inside the tubing is greater than outside, the tubing may buckle helically even in the presence of a packer-to-tubing tension. The tubing will always buckle, and much more severely, if free motion is permitted. The buckling may be prevented by pulling the tubing in sufficient tension. The prediction of these forces and tubing movement has here to fore been based upon calculations that did not inciude helical buckling. This paper preseitts means with which these length or force changes can be calculated while taking into account the effect of helical buckling. To avoid damaging formations, failure of remedial operations, or damage to the tubing or packer, application is made to practical problems involving calculations of the required length of seals, amount of sluckoff or tension, and prevention of permanent corkscrewing. INTRODUCTION Leakage of a packer may result in costly failures of such operations as squeeze cementing, hydraulic fracturing, etc. To avoid such failures, the authors are often asked questions pertaining to the length of necessary seals, the amount of necessary slackoff, etc. Published work' does not take into account helical buckling of tubing. Investigation of helical buckling was prompted by the fact that allowance must be made for this phenomenon in order to provide relevant answers. In the past, theoretical work on helical buckling was confined to conditions for which such buckling does not The mathematical treatment of behavior in a buckled condition, given in the Appendix, is novel. Assumptions upon which this investigation is based are listed and discussed in a special section. The following are a few of the many kinds of problems which may be solved with this paper. 1. Consider a packer in which tubing may move. Such movement will occur after pressures and temperature are changed. The paper provides means for: (a) calculating the amount of such movement and, therefore. the required length of seals; and (b) calculating the necessary amount of initial slackoff, for which there is no danger of unsealing the packer, if the length of seals is given. Such calculations, as well as those which follow, tully take into account the fact that part of the movement ib due to elastic helical buckling of the lower part of the string. This buckling may occur even in tubing under tension. Insufficient initial slackoff for a given length of seals, or insufficient length of seals for a given slackoff, may result in costly failures. A field case of such a failure will be given further in this paper. 2. In the case in which tubing cannot move in the packer, changes of pressure and temperature result in tubing-to-packer forces and forces in the tubing above the packer, both of which may be calculated. This knowledge is important because, if these forces are too large, the) could damage the packer or the tubing. 3. For wells in which wireline tools are to be run through the tubing, the paper provides means to keep the tubing from buckling, thereby permitting free passage of tools. 4. In deep wells, mainly in the presence of large casing, tubing may become "corkscrewed", i.e., take a permanent helical set. A field case is described further in the text. Using this paper, one may calculate in advance conditions under which permanent corkscrewing would occur, and then take preventive steps. HELICAL BUCKLING Consider a string of tubing, freely suspended in the absence of any fluid inside casing, as shown in Fig. I(a). Now consider an upward force F applied at the lower end of this tubing. This force compresses the string; and if the compression is large enough (which is always the case in actual problems), the lower portion of the string will buckle into a helix, as shown in Fig. 1 (b). The lower end of the tubing is subjected to a compression F. This compression decreases with the distance from the bottom and becomes nil (neither compression nor ten-

By A. Romero-Juarez

This paper is concerned with the effect of propping-agent concentration on flow capacity of a fracture in the case in which there is embedment of the propping agent. Previous published studies have shown definitely that there is a relationship between fracture flow capacity and prop ping-agent concentration, and it has been shown that the theoretical results are confirmed by laboratory experiments. The problem of directly finding sand concentration for maximum flow capacity of a sand-propped fracture is solved, and formulas and charts are given to obtain this concentration under various conditions of effective overburden pressure, medium sand-grain diameter and rock properties. It is shown that, for the same effective overburden pressure and the same rock characteristics, optimum sand concentration in pounds per gallon does not depend on medium sand diameter. For conditions met in bydraulic fracturing operations, it is found that sand concentration in grains per square inch for maximum flow capacity varies within a wide range of values; this indicates the convenience of using data of fracturing pressure and rock characteristics for calculating sand concentration in order to achieve the best results in fracture treatments. INTRODUCTION It has been pointed out in the published literature1 that one important factor controls the success of a hydraulic fracturing operation — the propping of the fracture. The main effect of the propping agent is to hold the fracture open by means of the reaction forces that oppose the pressure due to the overburden. It is assumed in this paper that the propping agent is sand, that the grains are spherical and uniform in size, and that this sand is distributed in a monolayer in the fracture. The existence of a sand concentration value for maximum fracture flow capacity has been recognized since the publication of one of the first studies on the subject.2 In the reference cited, flow capacity was assumed to be proportional to the cube of the fracture volume per square inch not filled by sand. The obtained experimental curves relating to flow capacity and sand concentration had the same appearance as the curves obtained with the afore-mentioned assumption. Recent work3 has shown that fracture permeability, in the case of a monolayer, can be calculated accurately by means of a modified Kozeny-Cacman equation; thus, it can be shown that fracture pqmeability is a function of free volume in the fracture and of the rock and sand wet surfaces. The flow capacity of a fracture is dependent on the permeability of the fracture and on the fracture width. If all excessive quantity of sand is present in the fracture, its width may be large but its permeability i:; low due to the greater flow resistance; too few grains of sand per square inch are present in the fracture, sand embedment in the rock is greater and the width becomes small enough to appreciably decrease the rate of flow. To determine optimum conditions of flow, therefore, it is necessary to know the dependence of fracture width on density or concentration of propping agent. This relation is given in a study4 in which the approach to embedment is similar to the one made in a penetration hardness test of metal. With the equacions presented by Darin and Huitt,3 the number of sand grains per square inch that results in maxirnum fracture capacity can be determined graphically by plotting fracture capacity vs sand concentration. Since the relationship between fracture capacity and sand concentration may be considered known, one is led to formulate the analytical problem of directly determining sand concentration for maximum fracture flow capacity, in order to study the effect of the various quantities that come into the process. The solution of this problem appears to be interesting both from the viewpoint of fluid mechanics and from the practical viewpoint of oil production in hydraulic fracturing treatments. EQUATION FOR FRACTURE FLOW CAPACITY It can be shown3 that the fracture flow capacity of a monolayer is given by the following expression,

By P. B. Baxendell, R. Thomas

Work on the calculation of vertical two-phase flow gradients by Cia. Shell de Venezuela has been based mainly on the "energy-loss" method proposed by Poett-mann and Carpenter in 1952. The "energy-loss-factor" correlation proposed by Poettmann and Carpenter was based on relatively low-rate flow data. This correlation proved inapplicable to high-rate flow conditions. In an attempt to establish a satisfactory correlation for high rates, a series of experiments was carried out at rates up to 5,000 BID in Cia. Shell de Venezuela's La Paz field in Venezuela, using tubing strings fitted with electronic surface-recording pressure elements. As a result of these experiments a correlation between energy-loss factor and mass flow rate was established which is believed to be applicable to a wide range of conduit sizes and crude types at high flow rates (e.g., above 900 BID for 27/8-in. OD tubing). It is anticipated that the resulting gradient calculations will have an accuracy of the order of % 5 per cent. At lower flow rates the energy-loss factor cannot be considered as constant for any mass rate of flow, but varies with the free gas in place and the mixture velocity. No satisfactory correlating parameter was obtained. As a practical compromise for low flow rates, a modification of the curve proposed by Poettmann and Carpenter was used. In practice this was found to give gradient accuracies of approxirnately ± 10 per cent clown to flow rates as low as 300 B/D in 27/8-in. tubing. INTRODUCTION Production operations in Cia. Shell de Venezuela's light- and medium-crude fields are principally concerned with high-rate flowing or gas-lift wells. Under these conditions the analysis of well performance, the selection of production strings and the design of gas-lift installations are vitally dependent on an accurate knowledge of the pressure gradients involved in vertical two-phase flow. Initially, attempts were made to establish the gradients empirically as done by Gilbert,' but the results were not reliable due to scarcity of data over a full range of rates and gas-oil ratios. Several methods of calculation based on energy-balance considerations were attempted, but the computations were cumbersome and the results cliscouraging. In 1952 a paper was published by Poettmann and Carpenter' which proposed a new approach. Their method was also based on an energy-balance equation. but it was original in that no attempt was made to evaluate the various components making up the total energy losses. Instead, they proposed a form of analysis which assumed that all the significant energy losses for mutiphase flow could be correlated in a form similar to that of the Fanning equation for frictional 1osses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The basic method was applied in Venezuela to the problem of annular flow gradients in the La Paz and Mara fields" This involved establishing a new energy-loss-factor correlation to cover high flow rates and, also, some adaptation of the method to permit mechanized calculation using punch-card machines. The final result was 1 set of gradient curves for La Paz and Mara conditions which proved to be surprisingly accurate. With the encouraging results of the annular flow calculations, several attempts were made to obtain a corresponding set of curves for tubing flow. Here, unfortunately, little progress could be made. The original correlation of Poettmann and Carpenter was based on rather 1imited data derived from low-rate observations in 23/8- and 27/8-in. OD tubing. It did not cover the higher range of production rates, and extrapolation proved unsuccessful. A new correlation covering high flow rates was required, but this proved to be extremely difficult to establish since tubing flow pressure measurements at high rates did not exist—due to the difficulty of running pressure bombs against high-velocity flow. The necessity for reliable tubing flow data increased with the development of the new concessions in Lake Maracaibo, where high-rate tubing flow from depths of 10,500 ft became routine. Thus. it was decided to set up a full-scale test to establish a reliable energy-loss factor for tubing flow conditions. A La. Paz field light-oil producer with a potential of approximately 12,000 B/D on annular flow was chosen. To obtain full pressure gradients, a special tubing string was installed which was equipped with electronic surface-recording pressure measuring devices,

Utah Development Company operates a mine at Blackwater with a present annual production of 4 000 000 tonnes of coking coal. Mineable seams outcropping on the company's lease are part of the Permian Mammoth Rangal Coal Measures. Current operations are based pre- dominantly on the Main Lower seam. Coal quality variations occur along the seam strike, in the direction of seam dip, within the seam plies and in isolated anomalous areas. Raw coal of non-specification quality is washed to reduce ash and sulphur and to improve the free swelling index. Raw coal meeting specification quality is sent directly to product, by-passing the washplant. Careful attention to mining, coal preparation and product blending is necessary to ensure that the combined product meets specifications.

Jan 1, 1974

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By Kendall E. Born

Production of crude oil in Tennessee during 1941 was slightly more than 15,000 bbl., about the same as in the preceding year. Two thirds of the total was from the Mississippi limestone pools in Scott and Morgan Counties. About a dozen small scattered wells in Clay, Pickett, and Fentress Counties, pumped irregularly, produced approximately 5000 bbl. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production by counties is shown in Table I. Drilling activities in the state fell to the lowest stage since 1933. Twenty-seven wells were spudded in during 1941, of which six were drilling or only temporarily suspended on Dec. 37, 1941. Of the 22 completions, four were gas wells of undetermined quantity, but are classed as commercial, and 17 were dry or near-dry holes. One well encountered oil, but it has not been tested. The total footage drilled during the year was 29,916 ft.; the average depth of wells was 1359 ft. The more important wildcats are listed in Table 2; the distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 3480 ft. in northwestern Anderson County, in the highly disturbed Appalachian area, a region long considered the most unfavorable in the state for the accumulation of oil and gas. Another test is now drilling below 2000 ft. in this general area. Cumberland Plateau.—There were two completions in the Cumberland Plateau area. One test, drilled in northwestern Scott County in an area of former Mississippi limestone production,' encountered a considerable amount of free oil at 850 ft., about the same horizon as in the old abandoned wells. No pumping tests have been made to date. A well at Oneida, Scott County, found gas at 1579 ft. in a sandy limestone of lower Mississippian age. The volume was reported doubled by a shot, although no open-flow measurement is available. Eastern Highland Rim.—Six completions on the eastern Highland Rim resulted in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area tested the upper part of the Knox dolomite group, one of which encountered some free oil in a sandy dolomite at 1670 to 1681 ft. A test high on a well-defined structure in Clay County found a considerable amount

Jan 1, 1942

By Kendall E. Born

Production of crude oil in Tennessee during 1941 was slightly more than 15,000 bbl., about the same as in the preceding year. Two thirds of the total was from the Mississippi limestone pools in Scott and Morgan Counties. About a dozen small scattered wells in Clay, Pickett, and Fentress Counties, pumped irregularly, produced approximately 5000 bbl. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production by counties is shown in Table I. Drilling activities in the state fell to the lowest stage since 1933. Twenty-seven wells were spudded in during 1941, of which six were drilling or only temporarily suspended on Dec. 37, 1941. Of the 22 completions, four were gas wells of undetermined quantity, but are classed as commercial, and 17 were dry or near-dry holes. One well encountered oil, but it has not been tested. The total footage drilled during the year was 29,916 ft.; the average depth of wells was 1359 ft. The more important wildcats are listed in Table 2; the distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 3480 ft. in northwestern Anderson County, in the highly disturbed Appalachian area, a region long considered the most unfavorable in the state for the accumulation of oil and gas. Another test is now drilling below 2000 ft. in this general area. Cumberland Plateau.—There were two completions in the Cumberland Plateau area. One test, drilled in northwestern Scott County in an area of former Mississippi limestone production,' encountered a considerable amount of free oil at 850 ft., about the same horizon as in the old abandoned wells. No pumping tests have been made to date. A well at Oneida, Scott County, found gas at 1579 ft. in a sandy limestone of lower Mississippian age. The volume was reported doubled by a shot, although no open-flow measurement is available. Eastern Highland Rim.—Six completions on the eastern Highland Rim resulted in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area tested the upper part of the Knox dolomite group, one of which encountered some free oil in a sandy dolomite at 1670 to 1681 ft. A test high on a well-defined structure in Clay County found a considerable amount

Jan 1, 1942

By W. B. Heroy

The rapid development of transportation routes on the African continent in recent years has greatly stimulated the demand for motor fuels and this in turn has led to more extensive exploration of such limited portions of the continent as seem to give promise of commercial oil production. In 1930, however, only two countries were classed as producers of petroleum and only one, Egypt, attained any importance. Egypt The petroleum production of Egypt is derived from the Gemsah and Hurghada fields on the west coast of the Red Sea and the Abu Durba, on its eastern shore in the Sinai peninsula. The Gemsah field, which began to produce commercially in 1912, has now practically ceased production, owing to the invasion of salt water. The Hurghada field has been producing since October, 1914. It now has about 60 producing wells. During 1929, a deeper sand with flowing produition was discovered in the eastern part of the field, producing oil of lighter gravity and free from water. The Abu Durba field was discovered by the exploration work of the Egyptian Government in 1918, oil having been found at a depth of 172 ft. This field has now 15 producing wells but a very small production. The production of these Egyptian fields over the last five years, is as follows: Metric Tons Metric Tons 1926......................... 172,881 1929....................... 271,520 1927......................... 184,557 1930....................... 277,146 1928......................... 269,324 This oil was all produced by the Anglo-Egyptian Oilfields Ltd., a constituent corporation of the Royal Dutch Shell group. During the year 1930 the Egyptian Government was engaged in geophysical prospecting of reserved areas along the Red Sea coast. Other Countries Soma1iland.—A geological survey of Somaliland was undertaken by the Somaliland Petroleum Co., Ltd., a subsidiary of the Royal Dutch

Jan 1, 1931

By Eric J. Bradshaw

For several hundred years the petroleum industry has flourished in Burma and at the close of the eighteenth century there were over five hundred producing wells in the Yenangyaung field. These were laboriously dug by hand and were exceedingly primitive, yet even today a small part of India's total production is obtained from hand-dug wells. The Indian Empire, the cradle of the oil industry, today produces but an unimpressive fraction of the world's supply of petroleum, not because the size of her contribution has diminished, but because it has remained more or less stationary while other countries have far outstripped her during the prodigious increase in the world's production of petroleum in recent years. Though for the past 10 years the total production in India has been remarkably constant, it has become increasingly difficult to maintain this output and at any rate from the older fields a slow decline may be anticipated unless new productive horizons are discovered. Production figures for the 10 years 192&1929 (the last year for which figures are available) are given by fields in Table 1. Crudes of Burma and Assam The bulk of India's production comes from the Yenangyaung and Singu fields, from which the crudes are very similar, the only important difference being that the oil from the Singu-Yenangyat structure contains a higher percentage of lighter fractions. The Burma crudes resemble that of the Panhandle of Texas and have a high content of solid paraffin, though strictly speaking the oil is of mixed base with a low content of asphaltum. With the exception of the negligible production from Sabe, the Burma crudes do not require dehydration; the sulfur content is very low and is innocuous. A small amount of naphthenic acids occurs in the kerosene and intermediate oil fractions while the lubricating fraction is practically free from acid. The ash content is low and the average A.P.I. gravity of mixtures of Yenangyaung and Singu oil is 36.4. Burma crudes require only light refinery treatment and practically dl the fractions are merchantable. Part of the gasoline supply is stripped

Jan 1, 1931