Search Documents

Jan 1, 1886

Jan 1, 1886

Jan 1, 1885

Summary of the morning's events with a Written Contribution to Paper No. 4 and author responses

Jan 1, 1947

Discussion of the papers with a written contribution and authors' written replies.

Jan 1, 1947

INTERNATIONAL conferences on safety in mines originated in 1912 when, in response to an invitation issued by the United States, representatives of Austria-Hungary, Belgium, France, and Germany participated in a conference held in Pittsburgh, Pa The record shows that a permanent organization was proposed to be developed through. diplomatic channels. However, the advent of war 2 years later prevented this proposal from coming to fruition. No further cooperation between the Bureau of Mines and a group having: similar interests in a foreign country took place until 1924, when formal cooperation with the Safety in Mines Research Board of Great Britain was established. Interchange of personnel and results of research under that arrangement have resulted in a number of publications in both countries and more rapid advance in knowledge than could have been obtained through the same efforts exerted independently.

Jan 1, 1950

Papers presented at a U.S. Bureau of Mines (USBM) technology transfer seminar describe the causes of violent material failure in U.S. mines, measurement techniques for monitoring events that result in violent failure, and mitigation techniques for controlling failure. Specific factors contributing to violent failure are identified on the basis of geotechnical monitoring in 16 U.S. hard-rock and coal mines and on statistical analyses of 172 coal bump events. New monitoring and analysis techniques developed as tools for assessing violent failure; geotomographic methods that provide new capabilities for the study of material failure and stress changes over large areas; and seismic methods for determining source locations, calculating energy release, and determining source mechanisms are described. Fair correlations have been established among seismic parameters, elastic stresses, face support load, and violent events. USBM studies have identified the advantages using both yielding and stable pillars for coal bump control. A computer program has been developed as an aid for selecting room-and-pillar layouts. The practical aspects of implementing a destressing program is outlined for coal mines, while the importance of mine orientation and timely support installation in controlling buckling-type failure is identified for hard-rock mines.

Jan 1, 1995

By G. H. Hope, D. Green

"Recent process advances at Lac Minerals Est Malartic Division are discussed. The Est Malartic mill treats massive sulphide, copper/gold ore from the Bousquet 2 mine, to produce a gravity gold product, a copper flotation concentrate and a gold precipitate. The mill operation has been improved by the application of Knelson concentrators to replace jigs, the application of Outukumpu high grade tank cells and optimizing the cyanide leach to minimize cyanide consumption.IntroductionThe Est Malartic mill is located near the town of Malartic in the Abitibi Region of north western Quebec. The mill has been in production since the mid- J 930's processing mainly clean, free milling gold ore. Active mining from the Est Malartic mine ceased in 1980 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that modification of the Est Malartic mill to handle this new ore source was economically more attractive than building a new facility on site. Modifications to the mill to process the high copper/gold ore from the Bousquet 2 mine began in late 1989 and the new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leach circuit continued operating on the copper flotation tailings with some minor modifications to the solution handling systems. An SO,/air cyanide destruction circuit was also added at this time."

Jan 1, 1993

By C. J. Ferron

Gold occurrence in operating plant tailings ranges from gold in solution, fine free gold, gold associated with sulphides/arsenides/tellurides and gold occluded within iron oxides or arsenates and silica gangue. This paper briefly presents various alternatives to reprocess gold tailings, with examples. These include the use of centrifugal gravity separators, CIL, magnetic separation, flotation and pressure oxidation.

Jan 1, 1993

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By T Raynlyn, S Hapugoda, V Nunna

The predominant phase in most Marra Mamba, channel iron deposits and detrital iron ore deposits is goethite. Goethite abundant iron ore fines tend to have complex mineralogical associations and fine dissemination of gangue material. These ores are typically challenging to process using conventional beneficiation methods. With declining ore grades, there is a need to develop new processing routes for low-grade goethitic ores/fines.Comparative process amenability studies were carried out using two different processing options to recover iron with low alumina and silica content from a low-grade goethite-abundant iron ore fines (-2 mm) sample from the Pilbara region of Western Australia. The first option involved dehydroxylation at 350°C and 400°C, followed by grinding dehydroxylated samples to 100 per cent passing 106 µm and magnetic separation. The second option was processing raw sample by gravity separation using a Floatex density separator. The performances of the two processes are discussed in terms of the iron grade-recovery responses, and an optimal processing route is proposed based on the findings from these tests.CITATION:Nunna, V, Hapugoda, S and Raynlyn, T, 2015. Process amenability studies on goethite-abundant iron ore fines, in Proceedings Iron Ore 2015, pp 165–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By A. L. Mular

"IntroductionThe mining industry has made slow but steady progress toward the automation of mineral processing plants over the last 35 years. The stimulus to automate is associated with important economic and hidden benefits, so that today, the latest in instrumentation and technology is being employed.This chapter assesses the status of instrumentation justified economically, defines levels of control and certain fundamentals of feedback control loops, describes typical sensors employed in concentrator circuits, summarizes control strategies employed therein, and briefly highlights trends in integrated plant control.Current Status of AutomationAs early as 1948, the mining industry began to show interest in automation, probably because of its close association with the petroleum industry. By 1958, some regulatory control had been achieved in various sections of a concentrator, particularly in crushing circuits. Successes were attributed primarily to the reliability of sensors employed in the corresponding control scheme. By 1961, computers had appeared on the scene, initially, for data logging purposes.From 1958 to 1965, very few new control strategies had been implemented. Guidelines in vogue at this time appeared to be:- Install proven automation, unless a good instrumentation department exists at the concentrator.- Do not bite off too much instrumentation at one time.- Do not purchase on price alone; instrumentation must function in the concentrator environment.- Do not purchase automatic control equipment to be fashionable.Such guidelines were employed1 because of a lack of: (a) quantitative process knowledge, (b) reliable primary sensors, (c) initiative to try something new, (d) trained personnel, and (e) understanding that older concentrators could justify automation in many situations."

Jan 1, 1989

By Reza Ghomashchi

Casting is the most economical route to transfer raw materials into readily usable components. The economics of casting would be more pronounced and better realized, if there are no or limited necessary post fabrication treatments. Therefore, there is an urge towards near or net-shaped casting as there are significant advantages over conventional casting including reduction of component weight, excellent surface finish, higher strength and integrity of the as-cast parts, closer tolerance, and the ability to produce pore-free parts by controlling the solidification shrinkage. The concept of near or net-shaped casting is currently employed for both semi-finished products such as strip-casting and finished shaped casting, as in case of high pressure die casting or squeeze casting. The full potential of this process yet to be explored and is expected to be realized within the next 10 years, especially in case of strip casting. The current article discusses different near or net-shaped casting routes currently employed for fabrication of high integrity finished products with main emphasis on aluminum-silicon alloys. In this regard, attempts will be made to identify the key parameters during fabrication and highlight the importance of process control and optimization in fabricating premium quality cast products. Keywords: Near Net Shape casting, Solidification, die casting, squeeze casting, rheocasting, thixocasting

Jan 1, 2003

By C. Larsen, R. A. Walker, A. Voth, C. Daoust

"The 3000 t/d mill at Hernia Gold Mines Inc. was commissioned in March, 1985. By Canadian standards the concentrator is highly automated, however, unlike the retrofit systems in many other plants, the Hernia process control system was installed during plant construction. This paper describes the Hernia control system beginning with system development (justification, architecture, start up, etc.), proceeding to current applications (crushing, grinding, leaching, etc.) and finally discusses some of the short term objectives for system improvement.INTRODUCTIONThe Hernia Gold Mines Inc. operation is located in the Marathon area of Northwestern Ontario. Controlled by Noranda Minerals Inc. (50.1 %), the cost of bringing the mine into production was nearly $300 million. A unique feature of the mine development was the extraordinarily short elapsed time of three years from Noranda's initial involvement to the start of milling operations. Additional background information on this project can be found in the trade literature (e.g. Tinter (1986). Scales (1987).)The Hernia concentrator is designed to process 3000 tpd of ore and commenced operation in March, 1985. Figure 1 provides a general plant flowsheet indicating the major circuits. Typical annual production statistics are included on the figure and these have been extrapolated from the available 1987 year-to-date data. Larsen and Tessier (1986) have previously described the operational aspects of the mill.In a metaphorical sense, the Hernia concentrator is like the traditional bride, ""wearing something old (e.g. the cyanide leach process), something new (e.g. a plant wide digital control system installed during construction), something borrowed (e.g. crushers from Gaspe) and something blue (e.g. the cladding on the surface buildings). While the prospect of fully undressing this bride is of considerable interest, here we choose to focus on something new. In particular, we choose to examine the process control system in some detail since Hernia is one of Canada's more highly autcmated gold mills. The control system is of interest because it has received suostantial credit for maximizing metal production and minimizing operating costs. With reference to the latter, it is worthy of note that Hem lo reports recent operating costs of less than $100 U.S./oz."

Jan 1, 1988

By N. R. Thornton

This paper discusses the rapid growth in the application of instrumentation for metallurgical process control. It covers such methods as ultrasonics, pulp density measurements, on-stream X-ray analysis and reagent control, as well as the expanding use of computer control and data acquisition.

Jan 1, 1971

By J. Fraser Forbes

"The meaning of the term ""process control"" has evolved significantly since its widespread use began in the manufacturing industries in the 1940s. Further, the scope of process control applications has drastically increased both in terms of the breadth of industries using process automation technologies and the vertical integration of these technologies within a single industry. This evolution and integration of process control technologies within the manufacturing industries has proceeded to such an extent that process automation is an integral part of modern business practices.This paper will examine the current status of process control technology from simple process regulation through process performance optimization to business planning. Each layer of the operations automation hierarchy will be discussed both in. terms of the current state-of-the-art and the directions in which these technologies are evolving. The key tools and tasks necessary for success at every level of the automation hierarchy will be introduced. Finally, the critical challenges that must be faced in accomplishing the goal of complete Computer Integrated Manufacturing (CIM) will be described.Finally, although this paper addresses issues of practical importance to any manufacturing company, the discussions will be framed in terms of the particular challenges facing and the opportunities available within the materials manufacturing industries."

Jan 1, 2000

By T E. Hayward, D H. English, S J. Smith

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007