Search Documents

By Fun-Den Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stabi1ity.l-3 Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe.3 Rock blocks formed by sets of parallel joints have been analyzed by Wittke.1,2 The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry. A plane of weakness is represented by its dip and strike in vector form and is reduced to the form of a linear equation. The geometry of the rock block is defined by solving the linear equations. The geometric characteristics of a rock block are based on triangles and tetrahedrons. By this treatment, the three-dimensional geometry is simplified and the number of calculations of forces and moments is reduced. Methods of finding the geometric characteristics are presented, along with equations for calculating the resultant forces and moments and the factor of safety. BASIC ASSUMPTIONS The following assumptions are used : The solid part of the rock mass is much stronger than the rock mass at the plane of weakness and the rock mass will only fail along planes of weakness.

Jan 1, 1972

By Fun-Den, Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stability. Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe. Rock blocks formed by sets of parallel joints have been analyzed by Wittke. The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry.

Jan 1, 1972

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Warren J. Bruckard, Mark I. Pownceby, Sazzad Ahmad, M. Akbar Rhamdhani

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Jan 1, 2015

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

Roof bolting has been widely used in hard rock underground mines for its many advantages. In this paper, the applicability of roof bolts to mine openings in frozen ground and effects of bolts on the stability of the openings are presented. A comprehensive finite element program ABAQUS, was used to analyze the temperature distribution, the stress field, and the displacement field around a mine opening. Openings supported by roof bolts and unsupported were analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration with a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts are less than five, the displacement within the ground can be improved only locally.

Jan 1, 1995

By J. Méndez-Nonell

The thermodynamic and chemical properties of SrSO4 and SrS in a gaseous flow of CO and CO2 at high temperature are discussed. The thermodynamic analysis of the system was made using data from the literature. The results obtained from the thermodynamic analysis were experimentally verified using the thermogravimetric technique. The experimental results suggest the formation of a complex compound between SrO and SrSO4. It was also found a change in the chemical mechanism of the process between SrSO4 and CO-CO2 and in the chemical mechanism of the process between SrS and pure CO2.

Jan 1, 1995

The additive property of dispersion variances was found experimentally by D.G. Krige using data from the gold deposits of the Witwatersrand. In this property, called ?Krige?s relationship?, the dispersion of a small unit, v, within the deposit is equal to the sum of the dispersion of v within a bigger unit, V, and the dispersion of these units, V, within the deposit, D. It is known that the variance of the grades decreases as the support increases, the so-called volume-variance relationship. To analyse volume-variance and Krige?s relationship, the methodology herein proposed combines blending piles and geostatistical simulation to simulate the in situ and the pile grade variability. Variability reduction in large piles is based on the volume-variance relationship, i.e. the larger the support, the smaller the variability (assuming perfect mix). Based on a pre-defined mining sequence to select the blocks that will form each pile for each simulated block model, the statistical fluctuation of the grades derived from real piles can be simulated. Using this methodology, one can evaluate within a certain time period the expected grade variability for various pile sizes, and also calculate the Krige?s relationship between the small blocks and the piles of different sizes. A real case study using a large Brazilian iron ore deposit illustrates the methodology and demonstrates the validity of the results.

Jan 1, 2014

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By D. M. Dabbs

A static dew point technique has been used to evaluate the solubility of arsenic in ?slag and its dependency on P02 at temperatures of 1458 and 1523K. The ferrous-ferric ion ratio of the slags ranged from 3.9 to 23.8. These values correspond to partial pressures of 02 ranging from 10-8 to 10-12 atm. The solubility of arsenic in slag was found to be independent of? P02? The data indicate that elemental arsenic exists in silicate ?slags. This result was further substantiated by mass .spectrometric analysis of doped slag specimens.

Jan 1, 1983

By J. V. Calara, J. D. Miller

The sign of the surface potential for complex non-reactive ionic solids cannot be predicted solely from consideration of the hydration energy of gaseous ions which constitute the ionic lattice. Accurate analysis of these systems must involve the hydration energy of surface ions, which requires knowledge of the crystal structure, the identification of cleavage planes, and the calculation of binding energies of surface ions. Surface binding energies for ionic solids can be determined if the Surface Madelung Constant is known. A computational technique was developed for the calculation of Madelung Constants for infinite lattices which gives excellent agreement with the values calculated by other more complicated methods reported in the literature. Extension of this technique permits the calculation of Surface Madelung Constants and binding energies of surface ions, [Aus], for semi-infinite solids. The hydration free energy of gaseous ions, [AFh], together with the calculated binding energy of surface ions, [Aus], allows calculation of the hydration energy of surface ions,[AGh], as for the case of the ionic solid, MX: [ ]

Jan 1, 1976