Search Documents

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By C. Haycocks

The problems caused by interaction in multi-horizon mining are world wide and are not limited to the coal industry. These problems will continue to increase as mining of new seams multiplies and replaces production from mined out horizons. Interaction problems are particularly evident in the Appalachian coal fields which contain many mineable, contiguously placed coal seams. Selection of the mining sequence of these seams, historically and currently, is based primarily on considerations of seam ownership, availability, and economics. Experience has shown, however, that mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. This interaction effect is often detrimental to the recovery cost and safety of mining the subsequent seams. Designing to avoid or minimize interaction effects represents a major challenge to the modern coal mining industry and therefore is the focus of this research. In an effort to evaluate past interaction effects and provide guidelines for future mine design, interactive ground control problems were categorized into four areas. These are pillar load transfer, massive interseam shearing, subsidence and pressure arching effects. To facilitate research, each of these areas was studied separately although in reality these subdivisions are arbitrary and have considerable overlap.

Jan 1, 1983

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district program. The Bureau's MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By John E. Trombly

System objectives and design criteria for an in-mine visual personnel paging system are discussed. Display technologies are evaluated and tradeoffs leading to display selection are described. The prototype dispatcher's console, battery/receiver box and visual display assemblies are functionally described. The report includes circuit descriptions, schematics, parts lists and equipment cabinet drawings for the three assemblies. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 1975

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By Norman] [Seldle

This report describes the development of a mine machinery training system from initial conception through a task and skill analysis, a training system analysis, implementation of a prototype system, and initial validation of the prototype system. The objectives of the training are to improve safety and productivity simultaneously via complete, thorough training. A task and skill analysts was executed for shuttle cars, continuous miners, cutters, loaders, face drills, tractors, and scoops. The prototype training system is for shuttle car operator training.

Jan 1, 1976

By Kenneth Wardell

Those flat lying, bedded or replacement, non-fossil fuel deposits which exist within the U.S.A., and which are amenable to longwall mining, are identified by reference to three principal factors associated with their physical/geological environments. These are their depth, extent and structural continuity. Technical feasibility is assessed in relation to the likely cutting speeds which can be achieved in the identified minerals with existing longwall shearer machines. Economic comparisons are made between traditional mining operations in those deposits for which technical feasibility is demonstrable. Continents are made concerning those technical deficiencies which appear to preclude the application of existing longwall equipment to the identified deposits and suggestions are made regarding the lines of research aimed at improving longwall technology.

Jan 1, 1978

By T. A. Lang

Concepts and equations have been developed to quantitatively determine the stability of a rock bolted coal mine roof as a structural (beam-arch) member consisting of reinforced rock units. The equations take into account: rock bolt tension, length, spacing, and orientation; size of opening, strength and physical properties of the rock; and loads from distressed rock, and were critically reviewed using sensitivity analyses and the results available from relevant previous analytical and physical model investigations. It is concluded that they can essentially be validated by using small scale physical models and the full size mine entry model at the USBM Spokane Research Center. However, a comprehensive research program, including analytical and laboratory investigations and field trials in typical mines, will be required to define and validate criteria and standards for using the equations as a basis for a rational design code for rock reinforcement installations to replace the semi-empirical rules now being used. For example, these studies have shown that the practice of installing vertical roof bolts with a uniform spacing equal to the bolt length is inherently unsafe and that the spacing should be reduced near the walls to prevent shear failure of the roof strata. The development of such a rational design code would provide enhanced safety in coal mining operations and warrants a high priority in the Bureau's ground control research program.

Jan 1, 1981

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The Objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Pedro Lilienfeld

This Final Report describes a program whose objective was to design, develop, fabricate, and test an airborne mass monitor for unattended and recording measurements of the concentration of dust in mining environments. Sensing collection are performed by beta-radiation attenuation and inertial implementation respectively. The instrument is portable, battery or line operated provides a digital printout of the mass concentration during each selection sampling period, as well as the accumulated mass of dust, and the elapsed sampling time.

Jan 1, 1974

By Martyn F. Roetter

The objectives of the work described in this report are to determine the communications requirements and need for communications, both for voice and control, on longwalls, and to make recommendations for longwall communications equipment and systems. These recommendations are designed to guide the future development of longwall communications. Information necessary for the accomplishment of this work has been gathered by a series of visits to longwall mines and discussions with longwall mine operators, as well as with suppliers of longwall communications and mining equipment and with Bureau of Mines personnel. In addition, it has proven possible, through personal interviews and literature evaluation, to gain an understanding of the experience and attitudes towards longwall communications in countries where longwall mining is far more widespread than in the U.S., namely the Federal Republic of Germany, the United Kingdom, France and Belgium.

Jan 1, 1976

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

By A. E. Kehew

Earth resistivity surveys using the Wenner electrode configuration were made in unmined areas and reclaimed spoils at three surface lignite mines in western North Dakota. The study sites were the Center, Indian Head, and Falkirk Mines. Automatic interpretation of the curves was accomplished with the method of Zohdy and Bisdorf (1975). Overburden materials become more homogeneous with respect to resistivity during the mining and reclamation process. The spoils curves show localized hetero-geneities probably related to discontinuous moisture content variations in the spoils. Consistent resistivity differences in spoils occur between mines with over-burdens of different mineralogic compositions. Groundwater chemical composition in terms of total-dissolved-solids (TDS) is inversely correlated (r=-0.61) with apparent resistivity at the 80-foot spacing from a survey centered at a piezometer screened near the base of the spoils. Better inverse correlation is probably pre-vented by high variability in TDS within the spoils groundwater. A useful predictive relationship may be the plot of mean apparent resistivity at the 80-foot spacing for ar. entire mine against mean TDS for all wells in spoils at that mine. Data from more mines are needed to test the hypothesis.

Jan 1, 1982

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By Paul S. Goodman

This report examines the feasibility of Employee Assistance Plans for the coal industry. Three issues are examined in detail. First, the prevalence of off-the-job factors such as alcoholism, drug abuse, and marital problems are examined in a sample of miners from the eastern, midwestern, and western underground coal fields. Then data were presented that examined the link between these off-the-job factors and behaviors critical to the mines such as absenteeism and turnover. Lastly, we examined the effectiveness of the major Employee Assistance Program in underground coal mining--the HELP Program. The report contains recommendations on whether coal mining companies should implement these programs and how these programs should be designed.

Jan 1, 1986

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979