Search Documents

The following pages discuss the objectives, the background, the scope and a statement of the problem of the study of methods to improve the pillar extraction practices in underground coal mines. 1. OBJECTIVES The objectives of this project were: ? to determine the principal factors contributing to high accident frequency and severity in both conventional and continuous mining operations; ? to compare and evaluate the safety aspects of the "open end" and "split and fender" systems of pillar mining; to establish basic data required to decide what constitutes an adequate pillaring plan that will optimize efficiency, recovery, and safety; ? to determine what measurements or information should be collected, (e.g. roof sag, pillar stress,) to make on-the-spot judgment of impending roof or pillar collapse; ? to make recommendations to improve existing methods or to insure proper techniques are implemented, and ? to suggest areas where additional studies or new research may be of value.

Jan 1, 1975

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International, Inc. (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period from 16 September to 1 November 1983. The testing covered herein is for coarse 2-in by a (minus 50 mm) Pittsburgh Seam coal in a 12-in (3 00 mm) pipeline, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s) and at concentrations ranging from 15 to 55 pct.

Jan 1, 1985

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period 22 November to 10 December 1982. The testing covered herein is for coarse 2-in by 0 (minus 50 mm) Pittsburgh Seam coal in a 6-in (150 mm) pipeline, at velocities ranging from 5 to 20 ft/s (1.5 to 6.1 m/s) and at concentrations ranging from 15 to 45 pct by weight.

Jan 1, 1986

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining I research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

Contract No. H0110929 was awarded by the U.S. Bureau of Mines in February, 1971, to DeTer Company, Incorporated, of Mountain Lakes, N. J. The contract provided for the modification of the contractor's Model 5000 Pressure Foam Generator to fit it for the suppression of coal dust in mines, a detailed testing program in a working coal mine, and for additional modifications and testing for the suppression of fires in coal mines. The contractual program was completed in April, 1972. The results of the dust suppression tests showed conclusively that the modified DeTer equipment effectively reduced the level of respirable dust in a working coal mine well below the present and future acceptable levels set by the Mine Health and Safety Act of 1969. The fire tests, carried out in a simulated mine entryway erected on the surface, demonstrated the ability of the DeTer equipment in suppressing fires of varying degrees of severity within an acceptably short time.

Jan 1, 1972

This report presents information developed during Bureau of Mines contract H0242016, "Mine Shaft Fire and Smoke Protection Systems" from May, 1974 through June, 1975. Purpose of the metal and nonmetal health and safety project was to evaluate mine shaft fire and smoke hazard problems, and to develop and demonstrate a low-cost, reliable mine shaft fire protection system that would protect against such hazards and would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines. Program effort proceeded through five phases, culminating in the successful in-mine fire demonstration of a prototype system. In addition to this final report, a film is available which depicts components of the system and its successful shaft fire testing at an underground mine.

Jan 1, 1975

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By Patricia R. Devine

This report expands an earlier study by Jack Faucett Associates (OFR #40-88) of the same title. Both reports are based upon an interindustry analysis from 1963 through 1982, during which time U.S. metals consumption and production did not keep pace with economic growth. The report discusses three sources of change: technological change, economic growth, and composition of final demand, as well as the relative importance of the individual components of final demand for metals. The results show investment and personal consumption to be the most metal-intensive components of final demand, and technological change to be the major cause of decline in consumption growth during the study period. Technology change is defined as alterations in production processes resulting in more or less consumption of metal per unit of output, often because of material substitutions and design changes. A trade analysis shows the significance of import growth, particularly indirect imports (metal contained in imported goods) as a factor contributing to the reduced growth rate of domestic metal production. The effect of import growth is partially offset by indirect export growth, suggesting that continued increase of all U.S. exports can have a strong effect in reducing the negative trade balance in metals.

Jan 1, 1988

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

U.S. Bureau of Mines contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment", was an investigative effort involving: ? Study of the fire problem on large mobile mining equipment ? Identification of equipment most prone to fire, to serve as a design case example ? Design of an improved fire protection system ? Demonstration of the developed system This effort was performed during the period June 1972 through May 1973, and was conducted in two phases. Phase I, June through November 1972, was devoted to identifying the fire problem and developing and evaluating design criteria. Phase II involved translating the design into hardware and demonstrating its effectiveness during actual fire tests, first on a wooden mockup of a truck, then on an operating truck at a working mine site.

Jan 1, 1973

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

By W. H. Ryback

When a fire or explosion occurs in an underground coal mine, the atmosphere guickly becomes irrespirable. Highly irritant smoke and toxic levels of carbon monoxide and dioxide are produced, and consumption of oxygen by the fire or blast can reduce its concentration below that needed to support life. Work parties entering such a hazardous atmosphere for rescue or recovery operations are required to use, as their primary respiratory protection, a fully self-contained breathing apparatus of at least two hours duration. Apparatus used in this role has primarily been of the closed circuit rebreather type, using pressurized oxygen storage and chemical removal of expired carbon dioxide. Typically, commercial self-contained breathing devices for mine rescue have been heavy, bulky, and uncomfortable to use. The McCaa apparatus, long the industry standard, represented the best art available when it was First designed in 1926. It weighs 41 Ibs., protrudes about six inches above shoulder height, and provides breathing gas at temperatures up to 120° F. More recent designs, such as the Drager BG174A and Scott Rescue-Pak, using modern light weight materials and fabrication techniques have improved on all parameters of the McCaa to some extent. It was the intent of the Bureau of Mines, acting under the authority of the Coal Mine Health and Safety Act of 1969, to fund the development of a new self-contained breathing apparatus which would incorporate the best available technology and serve as a benchmark for future commercial designs, as the Bureau-sponsored McCaa had 45 years previously.

Jan 1, 1974

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972