Search Documents

By W. Smith, F. G. Rinker, D. Beggs

Early in 1965 the Surface Combustion Division of the Midland-Ross Corporation was awarded the contract to engineer and construct a taconite pelletizing plant for the National Steel pellet plant, administered by the Hanna Mining Co., near Keewatin, Minn. This plant, which will have an annual capacity of 2,400,000 long tons, will produce pellets from magnetite concentrate using a new process developed through a joint research program by Midland-Ross, Hanna Mining, and the National Steel Corp. The work that culminated in the decision to construct this plant is the result of a research program for the development of the Midland-Ross heat fast process for the production of prereduced or metallized pellets. PELLETIZING PROCESS There are many acceptable methods for producing oxide pellets from ground iron ores and concentrates, and all of these give an acceptable product for blast furnace utilization. The vertical shaft furnace, the traveling grate, and the grate-kiln have been installed in many pelletizing plants in the northern hemisphere; therefore, the acceptance of these methods and the problems associated with them are well understood. However, this research project investigated a method for improving upon these processes to produce a high quality oxide pellet at a low operating cost.

Jan 9, 1966

By Cristiän Vargas, Jaime Simpson, Gerardo Cifuentes

"This paper presents a new process for the precipitation of Sb and Bi present in copper refinery electrolytes in the presence of Pb02 (Chilean Patent No. 45,037). To establish the conditions under which the precipitating compounds form, it was necessary to evaluate the amount of PbCh consumed, antimony extraction efficiency, precipitate stability, reaction kinetics, diffraction analysis and X-ray fluorescence, separation of size, plus observation of the precipitates in the electron microscope. Preliminary tests were carried with synthetic copper refinery electrolyte, and then the final testing was done with electrolytes from Chilean refineries. This process provides a real alternative for the treatment of copper refinery electrolytes for the control of Sb and Bi in solution; it is very simple to operate and is low cost compared with competing processes.Introduction.A high quality copper cathode implies a cathode free of impurities. The electrorefining process seeks to eliminate these impurities from the copper anode (99.5% purity) by its dissolution in an acid electrolyte using chemical and electrochemical reactions. As a result of this process, a cathode (99.99% purity) is obtained. If the concentration of impurities in the electrolyte, from the dissolved anodes, begins to increase; particularly if the antimony concentration in the electrolyte increases up 500 ppm, the formation of floating slimes which are a major cause of contamination of the cathode is favoured. The most important impurities from the point of view of their effect on the quality of the cathode copper, are Ag, As, Sb, Bi, Pb, Se and Te. Silver is necessary for the control of Se and Te. To control all of these impurities, it is necessary to establish different methods or parameters of control in copper electrorefining. These parameters are anode composition, additives, purification of the electrolyte, current density, acidity, etc."

Jan 1, 2012

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982

Provide an environmentally compatible means of producing lead from galena concentrates that replaces the current high-temperature pyrometallurgical primary lead smelting process and supplies pure lead metal within present and proposed Environmental Protection Agency (FPA) and Occupational Safety and Health Administration (OSHA) lead emission standards. Approach The U.S. Bureau of Mines developed an energy efficient and pollution-free leach-electrowinning method for use in recovering pure lead metal and byproducts from lead sulfide concentrates.

Jan 1, 1989

SUDBURY ore processed by International Nickel Co. of Canada Ltd. was recovered for many years as two mill concentrates, one primarily of copper, and the other mixed pentlandite-pyrrhotite, But, Since iron content of the nickeliferous pyrrhotite concentrate was ten times its nickel value, capacity of smelting was limited by the need for slagging the excess iron. A process for recovering the iron con- tent was developed after some years of research and a $20-million plant was constructed to employ the new method. Built near Copper Cliff, Ont., the plant started operation early in 1956, scheduled for separate treatment of 365,000 tons of pyrrhotite each year. It is only the first unit of an installation which will have a capacity of more than 1 million tons per year of pyrrhotite. By early 1958, production totaled more than 200,000 long tons of 68 pct Fe pellets containing 0.003 pct P, 1.5 pct SiO2, 0.01 pct S, and 0.15 pct Ni.

Jan 8, 1958

By Stanislas Mauuary

Price pressure is a real challenge on the stainless steel market. With market globalization, increase production capacity and exorbitant raw material, the margins are squeezing for stainless strip producers. Primetals Technologies offers a wide range of advanced technological solutions to secure the margins of our customers. Our solutions, implemented with professional project management, allow an optimum coil to market time, securing then the return on investment for the investor. Among the possible lever used to optimize the production route, one drastic step can be made to cut rolling time and cost by replacing the common 20-Hi mill stand reversing process by state of art high capacity X-HI® stands in continuous rolling line. Other source of savings can be implemented by integrated several process steps together (rolling, annealing, pickling, skin passing), achieving then savings on stocks and logistics while coil processing is reduced to fraction of hour. Additional solutions can also be implemented on the new, as well as existing line, like maintenance free solid state laser welder, skin-pass and tension levelers, in-line inspection system coupled with process and quality management system.

Aug 17, 2017

Commodities statistics and otter information are available through the following t et systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack. Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

Commodities statistics and other information are available through the following three systems: Internet Access: To access the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, environmental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone 4. After completing your selection, press the start button on your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gav Internet/Gopher Server: Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gav Internet System Administrator: webmaster®usbm.gov (or contact your local System Administrator).

Jan 1, 1995

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219 3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button o your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gov Internet/Gopher Server Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gov Internet System Administrator: webmaster@usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly. subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fumeless fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By V. A. Chanturiya, T. N. Matveeva, N. K. Gromova, T. A. Ivanova

"The research is aimed at solving the problem of increasing the extraction of gold from refractory ores, which are the main source of growth in gold production in the next decades. The purpose of the research is the development and scientific substantiation of the reagent modes for flotation extracting of gold from refractory ores using eco-friendly low-cost herbal modifiers (HM), providing increase in gold recovery and quality of gold concentrates. In the course of research laboratory techniques for the preparation of experimental samples of HM were developed, which included the sequence of operations of grinding Heraclium leaves and stems grinding, 2-stages extraction at a temperature of 50-60 °C, short-term ultrasonic treatment, filtration and subsequent unification of extracts. According to the developed method, the experimental samples of HM and conducted research were tested to analyze their sorption and flotation activity related to the extraction of gold from refractory gold ores.New data on adsorption and flotation properties of Heraclium stems and leaves extracts (HSE) in selective flotation of Au-sulfide minerals were obtained using UV-spectroscopy, scanning electronic and laser microscopy and atomic force microscopy. The dimensions and shapes of adsorbed hydrophilic films of herbal reagents were identified and mechanism of formation of stable insoluble compounds on the surface of minerals in flotation was explained.Research flotation tests carried out on samples of refractory gold ore of one of Russia deposits showed the possibility of effective use of herbal modifiers to improve qualitative and quantitative indicators of enrichment compared with the standard reagent regime. New reagent modes, using herbal modifiers in an amount of 5 to 10 ml of the extract (300 - 600 g / t, respectively) improves the quality of the concentrate: gold content attains 14.7 g / t, 1.34 times higher than in the baseline experiment and provides a gain of 3.13% extraction.The developed reagent regime with herbal modifiers is the author's original design, patented (patent of the Russian Federation) and have no analogues in the world of mineral processing. (Application number 2015116125 from 04.28.2015, ""The method of flotation separation of sulfide minerals using herbal modifier"", Russia). Actual application of new plant extracts as modifiers in flotation of sulfide minerals is the possibility of replacing of highly toxic chemical compounds by environmentally safe substances of plant origin. Implementation of the developed methods of extracting gold from refractory minerals with herbal modifiers will help to improve gold recovery at 3-5% and the quality concentrate of not less than 1.2 times, leading to higher productivity and a reduction of the negative man-made effects on the environment ."

Jan 1, 2016

By A. R. Javadi

Pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite (ZnS) and galena (PbS) generate hydrogen peroxide (H2O2) when placed in water, with pyrite generating the most amount of H2O2. The order of these minerals for generating H2O2 in water is: pyrite > chalcopyrite > sphalerite > galena. In previous research, the methods of generation of H2O2 in the grinding mill were studied. In this study, data from experiments were included by using MODDE 9 software for six parameters composed of water, grinding media, particle size; adding collector to the grinding, and adding depressant and pH. Finally the optimal condition was achieved. According to the results, most of the recovery is related to the particle 75 μ size and when using processed water, adding 100% collector and without depressant and pH 10. The most recovery of lead in the case of the use of fresh water is in the case of 100% collector, without depressant, pH 10 and 150 μ particle size. Maximum recovery in fraction size 45 μ in the case of water process is 100% collector, without depressant and pH 10. Maximum depressant of pyrite will be the fraction size 75 μ, distilled water, without collector, 100 depressant. Keywords: Sulfide mineral, hydrogen peroxide, flotation, oxidation

Jan 1, 2020

By A. Javadi

"Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Bama concentrator in Iran but with the addition i) Na2S reductant and ii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid.INTRODUCTIONOur recent studies have illustrated the formation of hydrogen peroxide (H2O2) by metal-sulphides during grinding in the presence and absence of oxygen (Javadi Nooshabadi & Hanumantha Rao, 2013a; Javadi Nooshabadi & Hanumantha Rao, 2013b; Javadi Nooshabadi & Hanumantha Rao, 2013c; Javadi Nooshabadi & Hanumantha Rao, 2014). In the absence of oxygen, it was found that pyrite surface is catalytically active and able to breakdown water molecules to form OH• free radical and thereby deriving oxygen in the formation of H2O2 from water molecules. The in-situ formation of H2O2 and its influence on sulphide flotation has not been addressed yet. The presence of strong H2O2 oxidant in the pulp liquid and its selective oxidation of pyrite would be beneficial in depressing pyrite flotation. Therefore, it is important to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp as well as to study possible ways of flexibly controlling the formation of these species through known chemical means for depressing the generation of the oxidant."

Jan 1, 2018

By Robert R. Grinstead

Two new ion exchange resins have been developed, which selectively absorb copper and nickel in preference to ferric iron from dilute sulfuric acid solutions of pH 1-3. The first absorbs copper and not nickel and can be readily eluted with 1-2N sulfuric acid. This resin is well adapted to the processing of copper leach liquors, including relatively low grade liquors obtained from dump leaching. The second resin absorbs nickel as well as copper in the same pH region, but only the nickel is eluted with 1-2N sulfuric acid. Elution of the copper requires much stronger (ca. ION) acid, altho both species are readily eluted with dilute (ca. lN) ammonium hydroxide. This resin, which should be useful in processing of certain types of copper-bearing solutions, may also be suitable for treating acidic nickel leach solutions of laterites and other non-sulfide ores.

Jan 1, 1976

By L Yang, L Chen, E Hu, D Tang

Online monitoring of particles cumulative percent passing (PCPP) for a target size at hydrocyclone overflow, compared with traditional offline methods, provides PCPP feedback in real time, and is advantageous in enabling energy-efficient comminution, increasing downstream flotation efficiency, and improving upstream resource knowledge. However, existing online approaches are generally costly and bespoke, and some are sensitive to operational changes. Therefore, this study proposes a new low-cost alternative based on accelerometer measurement for online PCPP monitoring in the overflow of hydrocyclones and provides a preliminary experimental investigation under dry condition. The proposed method uses a sensing probe inserted into the overflow pipe of a hydrocyclone to receive particle impact from the incoming slurry, with accelerometers attached to the probe and mounting frame outside the pipe for particle-probe impact detection. As a preliminary investigation before studying particle-probe impact events in slurry, tests under dry condition without fluids were conducted using dry sand particles in free fall from a fixed height. Accelerometer measurements are analysed in both time and frequency domains through root-mean-square (RMS) and fast Fourier transform (FFT). Results show that accelerometer measurements are useful in estimating mass flow rates, which are correlated to the accelerometer output amplitude RMS values in time domain, in a non-linear mapping. Different particle size classes can be identified by examining the accelerometer output amplitude at a known mass flow rate. Different particle size classes feature their distinct signature frequencies (SFs) that can be examined via FFT and the SF is found to be independent of the mass flow rate. The results imply that any PCPP changes can be detected by the change in the accelerometer output amplitude as well as a shift in SF, which demonstrates the effectiveness of using accelerometers to gauge changes in PCPP. Based on the current findings in dry condition, future work will investigate particle-probe impact events in slurry.

Aug 24, 2022

By Craig J. Brown

Despite its great potential utility, ion exchange has only achieved limited application in hydrometallurgy. To a significant extent this is due to the limitations of conventional ion exchange process design as well as the properties of the ion exchange resins themselves. Over the past decade several new ion exchange resins have been introduced with properties that make them potentially very useful for various hydrometallurgical separations. In addition, a novel ion exchange process called Reciprocating Flow Ion Exchange or Recoflo, which has been employed in the metal finishing industry for the last dozen or so years for chemical recovery and effluent treatment, has been shown to offer a number of unique and significant advantages over conventional I.X. technology.

Jan 1, 1984