Search Documents

By R. S. Silo

A new process for leaching oxidized copper ore (CuO) is presented. Its principle advantage is that it requires low cost raw materials. For large operations the only materials used are sodium chloride (NaCl) and calcium carbonate (CaCO3). In those operations of medium size, sulfur, which is abundant in the North of Chile, is used. However the process may also be applied to small copper plants provided low cost sulfuric acid is available as a substitute for sulfur. That is, it may be applied to those small capacity plants where large additional installations for the regeneration of the leaching solution are not needed. The method is comprised of six stages, namely: Crushing, Leaching, Washing of the Solution, Precipitation, Regeneration of the Leaching Solution, and Fusion. A flow diagram for this process in a large or medium-sized plant is given. LEACHING This process requires hydrochloric acid as the leaching solution for treating copper ores. This is easily produced from sulfuric acid and sodium chloride as follows: A small excess of NaCl is advisable to avoid the presence of free sulfuric acid. The experiments reported here were performed with 36 grams of HC1 per liter of solution to obtain a free acidity equivalent to 50 gpl of H2SO4 (the usual leaching solution concentration). Hydrochloric acid leaching may be done by either of the usual methods; i.e. percolation or agitation. The method selected depends on the characteristics of the ore. No matter which method is chosen, low pressure air can be used either as an air lift for circulation of the solution, or for agitation of the pulp with "Pachuca" tanks. In either case, there are no problems with respect to oxidation. Leaching by agitation produces good recovery; but at times, the problem of high consumption of leaching solution or the overproduction of grinding slimes which interfere with contact between phases negates this advantage. The percolation method was used in this study. Percolation took place in four 15-liter containers, 11 1/2 in. diam. by 12 in. height, having hemispheric bottoms. Each container was fitted with a wooden bottom having 1/4 in- holes. The air lift was a 3/4 in. plastic tube 10 in. high. Air at 6 psi was supplied from a rotating laboratory compressor. 10 kg of ore were charged to the container and counter-current leaching was used. The leaching solutions were fed through the center pipe in order to use the ascending solutions to reject the air in the charge. The solution circulated through the air lift in order to facilitate the movement according to the increase in density produced by the reaction between the phases present. Specific observations made in this report cannot be generalized because the leaching characteristics are dependent on the nature of the ore used, the method of leaching, and the production of primary or secondary slimes while crushing or leaching.

Jan 1, 1967

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.' Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method' was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.' Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By Claudio Guarnaschelli

Alteration of the electronic distribution of mineral surfaces by light irradiation has been used to modify the adsorption characteristics of flotation reagents. Energy of a few electron volts is suficient to cause the necessary transitions that either enhance or retard the adsorption phenomenon. The adsorption characteristics of potassium ethyl xanthate on galena and marmatite are presented as functions of the energy of illumination, type of semiconductor, and surface oxidation. In dilute solutions, the adsorption differences are readily detected by controlled kinetic measurements. The correlation between the electronic distribution and the adsorption and desorption phenomena at the solid surface is gaining more attention and acceptance. These interrelations have found a practical application in mineral processing since all of the sulfide minerals display semiconducting properties. By varying the ratio of free electron to electron vacancies, the separation of ilmenite from rutilel and zircon from pyrochlore" has been executed successfully. Plaksin et al.' indicate three possible ways of utilizing the semiconductor properties of a mineral. The first one involves the control of the oxidation-reduction potential of the liquid phase, the second one consists of allowing selected additives to diffuse through the mineral surface, while the third one entails a change in the adsorption and chemical activity of minerals by irradiating their surface. The aim of the present work is to consider the effect of irradiation on the adsorption-desorption characteristics of natural minerals. Since the effect of irradiation is to change the electronic distribution at the surface:

Jan 1, 1971

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By M. E. Wadsworth, A. S. Peck

Infrared spectra disclose that oleic acid will not adsorb on the surface of pure beryl unless the mineral is first activated with HF. The adsorption of oleic acid on HF activated beryl is attributed to the hydrogen bonding of oleic acid monomers to F-surface bridging sites. These sites are formed as a result of the reaction of HF with chemisorbed water or surface hydroxyl. Characteristic infrared spectra of physically adsorbed oleic acid are correlated with flotation at different pH at temperatures of 25°C and 75°C for colloidal and -60-mesh particles. The usual mode of occurrence of the beryllium mineral beryl, Be3A12Si6O18, is in granite pegmatites as pale green, white, or yellow crystals. A dark green gem variety, emerald, may be found in the wall rock of pegmatite veins or in mica schist. The most important beryl deposits in the United States are in the Black Hills District of South Dakota, and several mountain ranges of central and west-central Utah contain potential commercial sources of this mineral. Several papers have been published concerning the flotation of beryl with different conditioning reagents. Kennedy and O'Meara1 reported on the essential use of HF in the flotation of beryl from different ores. The use of calcium hypochlorite to separate HF activated beryl from feldspar after flotation with an amine collector was made by Runke.2 A report on the activation of beryl with different cations using sodium oleate collector was presented by Viswa-nathan and co-workers.3 Flotation of beryl with sulfonate collector and different activating salts was employed by Fuerstenau and Bhappu.4 The role of the surface charge or zeta potential in the flotation of beryl with different collectors and salts was also extensively investigated.5"7 Previous infrared investigations by the authors8 disclosed that the orthosilicate beryllium mineral, phenacite, reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. Thus, chemisorption is the effective mode of adsorption in the phenacite-oleate acid flotation system. In contrast, neither chemisorption or physical adsorption of oleic acid occur on the surface of pure beryl as evidenced in this study. Efforts were subsequently made to determine the mechanism of activation and collector adsorption for HF pretreated beryl. EXPERIMENTAL PROCEDURES Large, white, terminated crystals of beryl were obtained from Madagascar through Ward's Co., Monterey, Calif. The crystals were broken into -60-mesh fragments in a porcelain mortar. Part of this prepared material was ground to a powder with a Fisher Grinder using an agate mortar and pestle. The powder was transferred to a graduated cylinder and mixed with 500 ml of distilled water. After 5 min, the colloidal suspension was separated from the settled particles by decantation and used as a stock for infrared test determinations. Adsorption tests were performed by first transferring 20 ml of colloidal suspension to 50 ml glass centrifuge tubes. The solids were then centrifuged out and the liquid was discarded. Then, the solids were pretreated with one molar HC1 or one molar HF. After 15 min, the solids were again centrifuged out. The mineral solids were washed free of residual acid by repeated centrifuging and water washing operations. Then, 20 ml of distilled water was added to the solids, and the resultant suspension was used for test purposes. In the preparation of mineral for flotation tests, 1.5 g of -60-mesh beryl was deslimed by removing the colloidal fraction by three successive water washes and decantations. Then, the coarse particles were pretreated with either one molar HCl or one molar HF for 15 min. The mineral was next washed free of acid with distilled water, and 20 ml of distilled water was added to the beryl prior to collector conditioning. The conditioning of mineral with collector was performed in 50 ml centrifuge tubes to which either NaOH or HC1 was added for pH modification. One drop (6.0 mg) of U.S.P. reagent grade oleic acid or 2 ml of 0.01 molar sodium oleate was added to the pulp and stirred at about 1500 rpm for 3 min at a

Jan 1, 1968

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-'. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines ' has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a 'molecular fingerprint' of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward's Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-' was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-'. The ratio obtained by dividing absorbance at 1623 cm-' by absorbance at 1868 cm-' was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By L. W. Pommier, F. B. Brien

The Rheological properties of pulps are non-Newtonian in character and more than one viscosity parameter is necessary to describe their behavior, therefore, the single term 'apparent viscosity' which has been used in the past may be misleading. The study reported in this paper uses a dimensional analysis based on the Ostwald-de Waele shear stress-rate of shear model for non-Newtonian liquids to develop velocity and resistance equations for falling spheres. An electronic monitoring apparatus was assembled for determining the velocity of metallic bodies as they fall through opaque liquids and suspensions. By means of this apparatus the behavior of the viscosity parameters of the Ostwald-de Waele model and the applicability of the proposed equations were examined for a number of non-Newtonian liquids. The validity of the equations for these liquids was confirmed. Preliminary data collected using solid-liquid suspensions established the validity of the form of the basic equations for these systems. The differential movement of solid particles through solid-liquid pulps and suspensions is very important LO many branches of engineering, such as minerals processing, soil mechanics, ceramic slip processing, oil well drilling-mud technology, materials-handling in pipelines, and many others. There is a dearth of fundamental knowledge on the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The resistance offered by Newtonian liquids to the movement of free settling spheres is well described for laminar and turbulent conditions by Stokes' and Newton's Laws, respectively. However, problems are encountered when attempts are made to extrapolate these simple relationships into solid liquid suspensions. The rheological properties of pulps are such that they are non-Newtonian in character;'" that is, the applied shearing stress and resulting rate-of-shear are related by non-linear functions, and thus, in the simplest case two viscosity parameters are necessary to describe their rheological properties. For this reason the single term 'apparent viscosity' which has been commonly used to explain the flow resistance of suspensions and non-Newtonian liquids may be misleading. It is realized that a rigorous analysis of the rnechanisms of momentum transport of liquid-solid systems is complex indeed. There are many variables that affect the rheological properties of the systems such as density, size, shape, and surface energy of the suspended solid and density and viscosity of suspending liquid, as well as the solid to liquid ratio. However, it was felt that a useful contribution to the knowledge of the behavior of suspensions could be made by examining the systems in terms of the basic fundamentals of nowNewtonian flow. This has led to the development, by means of dimensional analysis, of velocity and resistance equations, using two viscosity parameters to describe the velocity of penetrating bodies and the flow resistance encountered by these bodies, as they pass through non-Newtonian systems. THEORY In order to examine the effects of the rheological properties of solid-liquid suspensions on the movement of immersed bodies it is appropriate to start with non-Newtonian liquids and develop equations, analogous to those of Stokes and Newton, for laminar and turbulent flow respectively, from which quantitative information may be obtained. Further investigation would then be directed at the complex suspension systems, and the effects of the many variables on the velocity and resistance equations. Liquids are classified on a basis of viscosity which may be defined as the relationship between applied shear stress and resulting rate of shear?-'* Pure single phase liquids composed of small light molecules behave as Newtonian liquids, having a single viscosity parameter since the shearing stress and rate-of-shear are related by a linear function. Bingham plastics are similar but have a yield stress. Of particular importance in our investigation are dilatant (shear thickening) and pseudoplastic (shear thinning) non-Newtonian liquids, with and without yield values.

Jan 1, 1968

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated' that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication' in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By J. M. Steininger

The mechanism of flotation of sphalerite with sulthydryl compounds of different acidities has been interpreted in terms of chemisorption of unionized collector molecules on hydroxylated zinc surface sites. At a constant collector concentration of 1.5 x 10 -4 M, the upper pH limit of flotation has been found to be directly and closely related to the negative logarithm of the collector acidity constant, pKa The experimental results indicate that flotation is prevented when about 95% of the collector is ionized. At low pH, collector adsorption decreases because of the reduction in number of hydroxylated zinc surface sites. These two effects explain why sphalerite does not float with the more acidic sulfhydryl compounds. Typical anionic collectors for sulfide minerals are short chain xanthates or dithiophosphates which are nearly completely ionized in the generally alka- line flotation circuits.1,2 Flotation mechanisms have therefore been usually interpreted in terms of ionic collector adsorption and competition with ionic depressants of the same sign as the collector. A few attempts have been made, however, to consider adsorption of neutral collector molecules. Contact angle measurements obtained by Wark and cox3 have been interpreted by Cook and Nixon4 as representing adsorption of the free acid molecules on sulfide minerals such as pyrite, galena, chalcopyrite, and sphalerite. Cook and Nixon tried to show that the free acid concentration of the collector was substantially constant along the curves relating collector addition and minimum pH for bubble adherence. However, in a review of the subject,5 Sutherland presented new data on the flotation of pyrite with mercaptobenzothiazole which did not support the hypothesis of constant concentration of either collector ions or collector free molecules. He further showed that, with the assumption of constant occupation of surface sites, both theories lead to relations between pH and collector addition having similar mathematical expressions. In fact, with the more likely assumption of variable occupation of surface sites which results in more complex relationships, it appears impossible to

Jan 1, 1968

By F. X. Tartaron

The comparison of actual energy of comminution with theoretical surface energy presents a wide gap. On the other hand, Solid State Theory presents a viewpoint that places actual energy of breakage in understandable relationship with the theoretical strength of materials. Therefore the physical background of comminution theory favors Kick's Law. A11 discussions of comminution theory appear farfetched when comparison is made of the actual energy of crushing with the energy input called for by thermodynamic theory. Quoting Taggart:' "The work required to crush halite was of the general order of 0.10 kg cm per sq cm of new surface produced (based on air percolation) whereas the theoretical energy of this new surface, based on thermodynamic calculation by a number of investigators is 1 x 10'4 kg cm per sq cm or the work expended was 1000 times the new surface energy — an indicated crushing efficiency of 0.10 pct." It is frustrating to probe into comminution theory with the prospect that the energy one is measuring is 99.9 pct waste energy. Do the laws of comminution deal with energy consumed by mineral breakage or with waste heat energy? There seems to be something wrong. Solid State Theory may provide the answer. The following statement is particularly apt to the situation: "The fundamental fact about metals and indeed all materials, is that they are much weaker than they should be. By this, we mean that if the stress required to cause a given plane of atoms to slip past a neighboring plane is calculated from basic atomic and Solid State Theory, the resulting number is some 1000 times too large to be accounted for by errors in approximations or assumptions. We know now that this is due to dislocations, and we even have a fair understanding of the details of the process by which dislocations make a crystal weak. An intriguing possibility which suggests itself, results from the discovery of very minute metallic crystals which are apparently free of dislocations and which have a strength approaching the ideal value for a perfect crystal." Here we have an extraordinary reversal of the situation. The actual energy for breakage is only one-thousandth the theoretical instead of 1000 times as given by Taggart. But the theoretical energy presented by Solid State Theory is the binding energy between atoms (or ions) in a crystal lattice. This is the kind of energy envisaged by Kick's law. The surface energy or the other hand corresponds to Rittinger's law. Comparison of theoretical with actual, on the basis of surface or on the basis of Rittinger's law, seems to present an absurdity; yet Rittinger's law is confirmed by an impressive array of experimental evidence. Comparison of theoretical and actual on the basis of Solid State Theory or, in other words, on the basis of Kick's law seems reasonable; yet there is not a scrap of evidence to verify Kick's law. The situation appears paradoxical, but the developments in the next section of this paper show that the paradox is a hint to a strange turn of events. ENERGY-WEIGHT FRACTION FUNCTION charles3 has presented a final equation showing the relation of energy consumed in comminution to size of product n{-1) a-n + 1 E is energy, C is proportionality constant, a and n are constants and k is the coarsest size in the ground product (size modulus). In the course of study of a large amount of experimental evidence, Charles discovered that in the general case, a-n + 1 approximated zero. For some reason, a and n differed only by unity. But if a—n + 1 = 0 within experimental error, then it is obvious that Eq. 1 states that it requires an infinite amount of energy to grind any sample to any size. This is a case where nature gives an absurd answer to a man-made mathematical equation, hence something is wrong with the equation. An adjustment must be made to fit the equation with experience. TO reveal the nature of the adjustment, the differential equation preceding the second integration in Charles' group of equations is given When Charles integrated the quantity xa-n it was almost impossible for him to realize that he was dealing with a special case of integration and that

Jan 1, 1962

By J. H. Polhems, R. B. Brackin, D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill. The Mascot ore is a lead-free, honey-colored sphalerite in dolomitic limestone, with lesser amounts of chert and some pyrite. A mineralogical analysis is given in Table I. After 10 years of successful operation with galena medium and treatment of nearly 10,000,000 tons of ore, a decision to convert to ferrosilicon was made early in 1948 because of the increasing price of galena and consequent high operating costs. The conversion was made on Nov. 6, 1948, and the results obtained since that time have shown remarkable improvement over those made with galena. The Table I. Mineralogical Analysis of Mill Feed, Pct Calcium carbonate 49.5 Magnesium carbonate 35.2 Iron oxide and aluminum oxide 1.5 Zinc sulphide 4.5 Insoluble 9.3 100.0 Table II. Comparative Data, Galena and Ferrosilicon Ferro- Diner-Gelenaa siliconb ence Operating costs per ton milled, ct. 21.21 9.12 12.09 Medium consumption per ton milled, lb 0.80c 0.15 0.65 Reagent consumption per ton milled, lb 0.45 0.02 0.43 Tailing assay, pct Zn 0.310 0.297 0.013 Concentrate. oct Zn 12.08 10.33 1.75 Heavy medla ieparatlon recovery. pct 89.38 90.22 0.84 Mill feed rate, tons per hr 153 166 13 Heavy mesa separation feed rate. tons per hr 100 10 0 Tons milled per heavy media separation man shift 350 620 270 Mill feed to coarse tailings, pct 51.0 56.7 5.7 Lost mill time, pct 5.6 5.0 0.6 Power consumption, kw-hr per ton 2.06 1.92 0.14 a 1947. " First 6 months of 1950. c Net consumption after deducting credit for reclaimed waste galena. Consumption of new galena was 1.320 lb per ton milled. For entire life of galena operation, a credit of 40 pct of the value of the new galena added was realized from the sale of waste galena. comparisons given in this report cover the first 6 months of 1950 as representing the ferrosilicon operation, and the year 1947 as representing the galena operation. This was the last full year in which galena was used exclusively and is representative of the best work done during the 10 years of operation with this medium. After only 2 years' operating experience, with ferrosilicon and treatment of 1,807,585 tons many advantages have been revealed and are summarized in Table 11. Development Prior to the introduction of the heavy media process, all the mill feed was crushed through 5/8 in. and treated by jigging. A finished tailing assaying 0.66 pct Zn was made on rougher bull jigs, and cleaner jig tailings were ground for treatment by flotation. The first test work on the sink-and-float method of mineral beneficiation was carried out at Mascot in 1935, using a 3-ft cone and galena medium for batch tests. The following year a 6-ft cone was installed for pilot-plant work. This unit became a part of the mill circuit on March 1, 1936, and handled a gradually increasing tonnage in the next 2 years as the process developed to the point where it could treat all the + 3/8-in. material in the mill feed. Coarse jigging was then discontinued on March 1, 1939, and all coarse tailings have been made by the heavy media separation plant since that time. Feed Preparation: The original feed preparation plant consisted of a drag washer followed by two 4x10-ft Allis-Chalmers washing screens. A surge bin and two additional 5x12-ft AC washing screens were added in 1943. Use of primary and secondary washing screens was found essential to provide the cleanest possible feed for the cone and thereby avoid excessive contamination of the galena medium. Improved washing was obtained by replacing the drag washer with a 7x20-ft Allis-Chalmers scrubber, shown in Fig. 2, which has been in service since May 1944. Throughout the life of the galena operation, delivery of extremely muddy ore to the mill overloaded the medium cleaning system, and it frequently was necessary to cut off the feed and clean the medium for several hours until its normal viscosity had been re-established. The cleaning circuit

Jan 1, 1952

By J. Mizrahi, A. M. Baniel, A. Mitzmager, S. Star

This article gives an account of the latest developments in the use of TBE for sink-float separation of silicate minerals. A number of minerals for which the process has been tested and found suitable are reviewed. Specific examples are discussed in relation to the particular problems of sink-float separation and recovery of TBE as compared with non-silicate minerals. The economic aspects are outlined. Silica and silicates comprise the most common and abundant group of minerals, and since they are present in variable amounts in most ores, they constitute an appropriate subject for the review and discussion of the recent developments in the use of TBE for mineral concentration. The silicates considered as a group have an extremely wide range of chemical and physical properties. Some of these properties, which are common to all minerals, are of importance to concentration by TBE and are discussed in some detail in this paper, as well as the development of methods and apparatus for concentration and recovery of TBE and several examples of concentration of silicates. PROPERTIES OF MINERALS WITH RESPECT TO CONCENTRATION BY TBE The properties considered as most important to concentration by TBE are specific gravity, structure, surface and shape. The specific gravity of a mineral is a fundamental property and is constant between very close limits for the same species of different sources if particles are pure and free from cavities or cracks. In many species, however, solid inclusions and changes in chemical composition due to replacement of elements cause variations in the specific gravity. The plagio-clase series of feldspars between albite and anorthite illustrate this point (specific gravity from 2.60 to 2.77). Fig. 1 shows the specific gravity distribution of some of the common silicate minerals.' The highest specific gravity is about 4.7 (zircon) and the lowest is 2.0 (sepiolite), with most of them ranging between 2.6 and 3.5. Although most of the silicates given in Fig. 1 are found as constituents of rocks, those generally considered as rock making minerals are comparatively few. They include quartz, feldspars, nephelite, sodalite, leucite, mica, pyroxenes, amphiboles, chrysolite, kaolin, talc and serpentine. These minerals may appear in igneous rocks as coarse crystals in granites, syenites and diorites or as very fine grained dispersions in basalt and felsite. When the latter rocks occur in an ore, their specific gravities depend on the minerals present and structure. The same is true for the sedimentary and metamorphic rocks (sandstones, shales, gneiss, slate, schists). A comparison of specific gravities for the minerals listed in Fig. 1 with that of TBE (see Table I) shows that the important rock-forming minerals, with the exception of pyroxenes, amphiboles and chrysolite (olivine), lie in the specific gravity range of less than 2.96 and can therefore be separated by TBE. The ore structure is important both in determining the apparent specific gravity and the efficiency of TBE recovery. The structure can be compact (as in

Jan 1, 1963

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By H. A. Hoffman

Competition from an all-flotation plant, with demonstrated economies and efficiencies, plus a change in smelting contract and introduction of improved cyclones lead to conversion from gravity-flotation. Detailed descriptions are given of equipment installed and procedures used at St. Joseph Lead's Federal mill. Future plans include further quality control by instrumentation in all aspects of the mill operation. Also planned are improvements in materials handling systems. Competitive conditions will continue to dictate improvements and changes in the mill flowsheet. The advent of all-flotation mills in the Lead Belt was introduced by the Indian Creek mill in late 1953. This modern and efficient plant then became a pattern for the other mills in this area to re-evaluate their circuits in an effort to develop flowsheets that would improve operating conditions and metallurgy. The Indian Creek mill demonstrated that all-flotation would require considerably less operating and maintenance labor than the combination of tabling and flotation that was common in the Lead Belt at that time. Two significant changes occurred in recent years to allow all-flotation to be seriously considered in other Lead Belt mills. One was a change in the smelting contract which did not require gravity concentrate. Another was the development of cyclones which provided classification of the flotation feed in a very small space. Since the Federal mill was the largest concentrating plant in the Lead Belt it was felt that the greatest savings could be made by investigating the all-flotation possibilities at this mill. Interest was stimulated by the milling and ore dressing Depts. to determine if this mill would be converted without undue cost, provided the metallurgy could be improved. Accordingly, laboratory tests were initiated to learn what metallurgical benefit could be derived. Numerous tests were run which indicated that grinding to all-flotation would improve the tailing by as much as 0.02 pct Pb. This was quite significant when multiplied by the tonnage of ore treated. Projecting the added cost of power for extra grinding and flotation, and the additional flotation reagents required, plus additional new equipment that would have to be purchased, it would still add up to a considerable saving. The all-flotation mill would reduce man power by some 30 pct, and make a metallurgical improvement. Operating costs could be reduced bv 2$ per ton. The metallurgical improvement would amount to 4$ per ton, for a total of 6$ per ton of ore milled. An estimate of the cost of the conversion was set at $250,000. With the savings as estimated this could be paid off in about two years. On paper it therefore seemed attractive enough to justify a mill test. MILL TESTING One section of the Federal mill was made available for use as a separate test circuit. Cyclones and density controllers were borrowed from the Viburnum and Indian Creek mills. Denver flotation cells were obtained from the Desloge mill that was then shut down. Two 10-cell groups of Fagergren flotation machines, consisting of eight roughers and two cleaners in each bank, were segregated from the remainder of the plant. The 9x12-ft rod mill was continued as a primary grinding mill. The two 6%x12-ft mills on this section were converted from rods to balls, and the speed increased to 22.0 rpm. Cyclones were installed to close the circuit of these ball mills. The ground pulp from each of the ball mills was fed separately to its own bank of flotation cells so that two completely separated test circuits could be run in parallel. This test circuit operated on a three-shift basis from Dec. 22, 1959 to Mar. 21, 1960. The first few weeks were occupied in developing conditions for proper metallurgy and trouble-free operations. Results were rather erratic but as the ore dressing laboratory and the mill operators became more familiar with conditions they were able to obtain expected results, which could be duplicated day after day. The last five weeks of testing indicated the best results and are tabulated in Table I. During the first two weeks a Denver unit cell was used on No. 1 flotation circuit. Even though it recovered almost one half of

Jan 1, 1962

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,' a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.'," Properties of Ferromagnetic Materials:'7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.' His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961