Search Documents

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

By R. M. Brick, R. G. Treuting

DESPITE the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- [ ] ance and distribution of slip lines,[$] the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about ½ in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. I and 2). Restressing the crystal caused additional markings to appear at an initially lower [ ] stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C., the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggenberger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1941

By Yonghua Li, Fanling Meng, Weitao Zheng, Xiaodong Wang

The NiTi thin films were deposited onto copper substrates by magnetron sputtering. Tensile tests were carried out on CSS-44100 electron universal test-machine. X-ray diffraction profile Fourier analysis method has been used to study the mechanical properties of deformation NiTi thin films. The surface micrographs of the NiTi thin film were obtained using scanning electron microscopy (SEM). It has been found that the dislocation density and the deformation storage energy density increased with elongation increased. Microhardness was calculated from the dislocation data. The results showed that the microhardness values were not in a good agreement between calculated values and measured values. The oxide layer on the surface of NiTi thin film affects the measured values of microhardness. The Vickers hardness measured values are larger than the calculated values. The experimental results showed that a series of parallel cracks grew in a concerted fashion across the thin film and the cracks were equally spaced.

Jan 1, 2015

By S. Seetharaman

The present paper presents. the concept of micro-models and illustrates the application of the same in the simulations metallurgical processes. Development of micromodels requires access to accurate thermodynamic, thermophysicaland kinetic information for the relevant systems with suitable models to extrapolate the data as functions of temperature and composition. Experimental measurements and modelling of the thermodynamic properties, sulphide capacities and viscosities of oxide melts carried out in the department are presented. The incorporation of these models in process models, with special reference to ladle refining of steel is illustrated. Typical example of micro-modelling of solid-gas reactions is also presented.

Jan 1, 1999

By Lj. D. Andric

By the micronization-milling of the material, the size and the structure of its particles are changed and it comes to the increasing of the potential energy of the system as well as to the chem-ical activity of the material what is the result of an increased free surface and of the concentration of the grate defects, that is of the internal energy of the system. All these changes that are reached, show that new characteristics of treated materials are got by micronization process. Controlling the process of the micronization and by purpose directing of the new characteristics of the activated materials, we can have the positive effects and use them in more technologies. Talc is important nonmetallic mineral raw material that is widely used as either the basic raw material, or as filler. This has stimulated its technological investigation, as well as the investigation of its physical-chemical characteristics. In this paper are shown experimentally reached results of the physical-chemical characteristics of the talc during the process of the micronization in high energetic mill. In this paper, the optimum conditions of miconization of talc in high-energy-speed rotary mill and its influence micronization on a degree of Fe2O3recovery by hydrometallurgical methodes, are presented. The X-ray analysis of the obtained products showed that high quality talc with low content of can be obtained by these physical-chemical processes In this paper, the principles and application or fine and ultra-fine grinding high-energy attriton mill with small balls, enabling fast, efficient grinding, low energy consumption, short grinding time and easy handling will be described.

Jan 1, 2014

By A. Vilinska

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineral-solution interface. Recent developments in biotechnology have not only aided hydrometallurgical leaching operations but also shown great promise in mineral beneficiation processes. The adhesion of bacteria on minerals alters the surface properties relevant to flotation and flocculation of minerals. The biomodification of mineral surfaces occurs through the attachment of microbial cells, oxidation reactions and adsorption or chemical reaction with the metabolite products. Several types of heterotrophic and chemolithotrophic bacteria have been successfully applied in flotation and flocculation processes for the last two decades. Al-though the potential of microorganisms in minerals beneficiation has been realised by several re-searchers from their laboratory investigations, the studies were mostly confined to pure mineral systems and there is hardly any sincere effort to apply the methodologies on ores. This paper presents a brief summary of the literature in bioflotation and bioflocculation, and attempts to outline new dimensions of research for a practicable application of this technology in mineral industry.

Jan 1, 2014

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral's Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about 10 minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag-carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By Gary L. Mowrey

Visible and sometimes audible indications of excessive underground rock pressure such as pillar fracturing, squeezes on chocks, and "roof talk" are familiar to mining engineers. Such signs often precede rock failure on a larger scale and therefore may be used as a warning. Nevertheless, these subjective observations do not provide an adequate means of evaluating the existing rock pressure conditions in a mine. One method which appears to be extremely promising in determining the stability of geologic structures in general is that of monitoring their associated micro seismic activity. Mining engineers generally agree that during the process of rock deformation and failure small-scale seismic ("microseismic") vibrations are produced in the rock itself. These transient vibrations propagate through the rock structure and may be detected at a considerable distance from the failed rock by employing suitable electronic monitoring equipment. Hardy (1) has presented a detailed review of microseismic research in the mining, petroleum, and geoscience areas, and it is apparent that relatively little application of micro seismic techniques have been made in coal mines. This is especially true in North America since here most coal mines are fairly shallow and consequently are not generally subjected to excessive stresses. Furthermore, strict Federal and State mining laws limit the use of electrical equipment in coal mines complicating the use of the necessary monitoring facilities. In terms of both mine safety and economics, monitoring microseismic activity appears to be invaluable in the detection and location of over-stressed pillars and unstable roof conditions caused by development and production work. In 1970 The Pennsylvania State University Rock Mechanics Laboratory became involved in a research project, sponsored by the U.S. Bureau of Mines, to investigate the feasibility of using microseismic techniques to detect and to locate potential regions of instability around a longwall coal-mine operation [Hardy and t10wrey (2); Mowrey (3)]. In this study geophones (velocity gages) located in an array of shallow boreholes drilled from the surface above the active area of the longwall were employed to detect microseismic activity, and a mobile micro-seismic monitoring facility was used to condition and record this data for later analysis. This project is unique in that measurements were made from near-surface geophones rather than geophones installed on the mine itself. Two advantages are apparent, namely that (1) there are no electrical limitations on the monitoring system and that (2) mining operations can continue normally because there is no monitoring equipment or cables in the mine.

Jan 1, 1978

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Vera Lúcia Othéro de Brito

Literature has shown that spinel Co-Mn ferrite have potential application in magneto-mechanical sensors, due to its relatively high magnetoelastic sensitivity. In this work, Co-Mn ferrite was processed by means of the ceramic method, using Fe2O3, MnO and Co3O4 as raw materials. Samples were liquid-phase sintered, using Bi2O3 additive as liquid-phase former. X-ray fluorescence analysis was carried out in the raw materials in order to evaluate their impurity content. Atomic absorption spectrometry analysis was used for quantifying the Co/Mn/Fe proportion in the ferrite. The microstructure of the sintered sample was analyzed by means of Scanning Electron Microscopy. The magnetization and magnetostrictive behavior of the ferrite were evaluated, obtaining curves for magnetic hysteresis, magnetostriction and magnetoelastic sensitivity. The impurity inclusions and the Bi-rich particles formed from the liquid phase were characterized. The sintered ferrite had a total magnetostriction of -126ppm, which is lower than the values reported in literature for a Co-Mn ferrite of similar composition. It was verified that sintering was carried out within a critical temperature range, in which the decomposition of Mn ferrites may occur when sintering in air. This decomposition affects the magnetic properties of the material, and it may be avoided by using controlled sintering atmospheres.

Aug 8, 2018

By Ananda Moreira Vaz Ourique de Avila

Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells (SOFC) interconnects, replacing the ceramic materials. However, at high temperatures, on the order of 700-850 0C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the SOFC. Thus, the knowledge on kinetics of oxidation/corrosion of these steels and their relationship with the microstructural transformations are of great importance. In this study, samples of ferritic stainless steels AISI 430, AISI 441 and Crofer22APU® were tested for oxidation at high temperature (800 0C) for long periods of time (up to 3,600 hours) and mass gains were monitored allowing the determination of the oxidation behaviors of these steels. Additionally, the microstructural characteristics of the samples before aging (corrosion-oxidation test) and after various oxidation times were evaluated by optical (OM) and scanning electron microscopy (SEM), as well as by micro chemical elemental analysis (EDS) and X-ray diffraction (XRD) phase analysis. Electrical characterization allowed determination of electrical area-specific resistances (ASR) characteristics of the systems studied, thus relating the electrical and oxidative behaviors of steels evaluated.

Aug 7, 2018

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006