Search Documents

By Tevfik Güyagüler

Airborne dust is one of the important environmental problems in mines. Besides conventional dust control methods, recently, extensive studies have been carried out on the elimination of dust before it has actually been formed. Determining to what extend rock characteristics influence the amount of dust produced during different mining activities are considered as a guide for this purpose. The factors analyzed in this study were main mechanical, physical properties and petrographical constituents, namely free and combined silica. In the study regression analysis techniques were applied to investigate the effectiveness of aforementioned factors. INTRODUCTION Nearly every aspect of mining activity contributes to the air pollution caused by dust. Therefore the harmfull effect of airborne dust has been investigated many years and limit dust concentration levels were determined for various types of mine dust. To keep the dust level below limit value different dust control techniques have been applied in mines. So far, the well known techniques regarding dust control focuses on reducing the amount of airborne dust. However, recently various studies have been carried out to avoid the dust before it has actually been formed (Bhaskar and Gong, 1991). In this respect, influence of rock characteristics on dust formation is regarded as a guide for this purpose. The present contribution describes such a study in which the drilling operation is considered as the source of the dust. In this study drilling and dust sampling process were undertaken in a model gallery that simulates an underground working. The mechanical and physical properties of the rock samples were measured in rock mechanics and ore dressing laboratories. Quartz and combined silica contents of the rock samples, on the other hand, were determined in the laboratories of geological engineenring department. Rock samples used in the research were different types of coal measure rocks, namely, sandstone, shale and conglomerate. The rock characteristics studied in this work are brittleness, toughness, rock strength, hardness and hardgrove index as inherent properties; free silica, and total silica contents of rock samples as petrographical constituents. Although there have been various studies to determine the effect of rock characteristics on the dust formation, still the type and extend of effectiveness have not been understood clearly. LITERATURE REVIEW Most of the studies investigating the effect of rock properties on dust formation concluded that they are effective. In such an investigation, it has been found that inherent rock properties influence dust formation (Das, 1973). In the another study, dustiness of the air was considered as a function of the composition, hardness and moisture content (Panov, 1967). It was also accepted that in a drilling operation more fine dust is produced if the rock to be drilled is hard (Skochinsky and Kamarov, 1969). In some other investigations dust production were considered as a function of hardgrove index (Moore and Bise, 1984) or formulated in terms of brittleness, toughness and hardness (Güyagüler, 1991). The effect of the petrographical properties of coal or rock on dust formation characteristics have also been studied (Baafi, 1979) (Panov, 1967). Because of its importance, various researches were conducted the study to find out the effect of free and combined silica content of dust on dust formation. In one of the study, the relationship between quartz in the coal seam and quartz in the airborne coal dust was investigated (Ramani et al, 1988).

Jan 1, 1993

By Kamran Esmaieli

This paper investigates the behavior of ore pass walls under impact loads caused by material transiting through an ore pass. In particular it considers the influence of foliation in the rock mass surrounding an ore pass as both a triggering and accentuating cause of degradation. Based on empirical observations in several underground mines a numerical experiment was designed to understand the influence of rock mass foliation on impact-induced damage on ore pass walls. The distinct element method, and in particular the Particle Flow Code (PFC2D) was used to simulate three different rock masses surrounding an ore pass. Each simulated rock mass has similar properties but was defined by distinct dominant foliation (70o, 80o, 90o) along the foot wall. The numerical experiments investigated different scenarios whereby the walls were loaded by a projected rock fragment striking the foliated walls at a constant impact angle and velocity. The damage inflicted by the projectile rock fragment, on the foliated rock mass, was quantified using the number of impact-induced micro-cracks initiated on the ore pass wall. The results of the numerical analysis indicated that the presence of foliation resulted in greater damage zones in the surrounding rock mass. In addition, the extent of impact-induced damage to the ore pass wall increased as the angle of interception between the ore pass wall and the rock mass foliations decreases. This is in agreement with qualitative field observations.

Jun 1, 2012

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Siyuan Zhang, Lu Lin, Yanping Bao, Wei Xiao, Chaojie Zhang

In order to decrease high aluminum consumption in Interstitial-Free (IF) steel production in a steel plant, Ruhrstahl Heraeus (RH) process data from 2428 heats were analyzed by statistical methods. The results showed that the blowing oxygen quantity and oxygen activity, before the RH and before deoxidization, have positive correlations with aluminum consumption, especially the blowing oxygen quantity. Waiting time before refining also has a positive correlation with aluminum consumption when it exceeds 7 min. On the contrary, steel temperature before RH has a significant negative correlation with aluminum con sumption, when it is between 1600 and 1630 °C. According to the statistical results, the RH refining process was optimized when the steel temperature before RH was controlled between 1630 and 1645 °C, waiting time was controlled at less than 7 min, blowing oxygen quantity was controlled to less than 100 m3, and the oxygen activity before RH was controlled between 0.050–0.075%. After optimization, the reduction of aluminum consumption was remarkable. Average aluminum consumption decreased from 1.45 to 1.17 kg/t steel.

Mar 1, 2017

By P Ramsaywok

The use of saline water for mineral beneficiation in arid regions is general practice and also the case with Exxaro Namakwa Sands, situated on the west coast of South Africa. Although it is ‘cost effective’ to use sea water for mineral beneficiation, downstream process separation efficiencies may be negatively affected. This is more specific to surface dependent separation techniques such as electrostatic and high tension (HT) separation. If minimal fresh water is available then, proper washing is often neglected. Salt crystals can form on particle surfaces during the drying process before electrostatic separation.This paper describes a study that has been conducted to determine the effect of upfront salt water processing on downstream electrostatic/HT separation. The study indicated that minor quantities of salt can cause the separation efficiency to decrease substantially.

Oct 5, 2011

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By H. C. Kenny

THE annealing or softening temperature of cold-worked copper is appreciably increased by almost unbelievably small amounts of silver. As indicated by some data in this paper, the softening temperature of high-conductivity, tough-pitch copper may be increased from 200° to 350° C. by the addition of only 15 oz. per ton (0.052 per cent) of that element. Because it has this higher annealing temperature as compared with the silver-free metal, silver-bearing copper finds considerable use in industry. For example, when hard-rolled copper is used in operations that involve soldering or tinning, silver-bearing copper insures against loss of strength, whereas silver-free copper becomes "dead soft." Yet-though several investigators, beginning with Caesar and Gerner1 in 1916, have shown that small amounts of silver do definitely raise the softening temperature of copper-data are lacking on the problem: What is the specific influence of different amounts of silver on this tem-perature? It was to help in filling this gap in the knowledge of what might be termed "alloy coppers" that the data given herein were obtained. The softening of cold-worked copper depends, of course, on a number of factors, of which the composition of the material is only one. Other highly important factors are the degree to which the material is cold-worked and the time it-is held at the annealing temperature. The method of cold working and the grain size of the metal produced are also signifi-cant. All these variables were taken into account in the investigation reported here, and the influence of silver on the electrical conductivity and on the working was also considered.

Jan 1, 1934

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By Sureshan K. Moothedath

This paper provides a mechanistic representation for floc formation, growth and degradation and presents results from an experimental study of batch flocculation in which step changes were made in the impeller speed, flocculant addition, and slurry concentration. A discussion of the experimental results is included in terms of the mechanisms of floc formation and size-change.

Jan 1, 1993

By Joshua Hofman, Braden Lusk, Erin Morris

Explosions in urban environments, whether of accidental or malicious cause, often result in extensive injuries, loss of life, and property damage. The ability to predict the damage inflicted by these events is highly sought after; in order to predict damage, the behavior of blast waves within these environments must be quantified and understood. Urban constructs such as buildings and roadway intersections affect the natural propagation of a blast wave, intensifying or rarefying the wave depending on their arrangement.

Jan 1, 2012

By D. J. Jr. McAdam

PART I.-OUTLINE OF INVESTIGATION, DESCRIPTION OF METHODS AND MATERIAL Previous Investigation of the Influence of Stress on Corrosion IN 1917 Haigh1 presented evidence that under simultaneous corrosion and cyclic stress metals may fail at lower stresses than if the corrosion is prior to the cyclic stress. In 1926 the author, while investigating the cooling effect of water on the fatigue resistance of metals, found that under these conditions steel specimens fail at stresses far below the endurance limit.2 (By "endurance limit" is here meant the fatigue limit obtained with specimens as free as possible from stress concentration and corrosive influences.) This led to an investigation (at the Naval Engineering Experiment Station, Annapolis, Md.) of the influence of cyclic stress on corrosion. This investigation maybe divided into three parts. The first part was a general survey of the conditions necessary to cause complete failure under corrosion and cyclic stress of relatively high frequency. The entire process by which metals fail under these conditions was-called "corrosion-fatigue." "Corrosion-fatigue limits" for a large number of metals were determined and the relationships of these limits to chemical composition, heat treatment and physical properties were established. The conclusion was reached that corrosion-fatigue is due to the accelerating influence of cyclic stress on corrosion. Results of this part of the investigation were presented in five papers.2-6 The second part of the investigation was a preliminary study of the influence of cyclic stress on corrosion. Each experiment was conducted in two stages. The first was a corrosion stage in which the specimen was corroded under cyclic stress; the second was a fatigue stage, in which the previously corroded specimen was tested (without further corrosion) to determine its fatigue limit. The difference between this fatigue limit and the endurance limit was used as a criterion of the "damage" due to

Jan 1, 1931

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By Gregor Kücher

Lack of basic knowledge on the semi-direct recycling methods for hard metals hinders the application on an industrial scale. However, advantages like reduced expenses and lower environmental impact draw interest at future potentials. Consequently, this report aims to offer insight into the influence of varying bulky hard metal substrates during their lixiviation in acidic media with an oxidant. The statistical software Modde 11 assisted in the development of a design of experiments (DOE) for evaluation of the impact of average grain size, binder and tantalum carbide (TaC) content on the leaching characteristics. The other experimental parameters were constant. Among them were temperature, solution concentration and quantity, duration and substrate surface exposed to liquid volume. Eventually, prediction plots and factors of the computed model equation describe the effects of varying substrate qualities on leached binder metal and selectivity.

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

In this research study, the interaction of particles with substrates of different roughness magnitude was investigated. Particle surface treatment, relative humidity (RH), and surface roughness levels were controlled in order to achieve separation of different particles by applying removal forces. Three different approaches to reproducibly roughen surfaces were used. Initially, glass disks were laser engraved to create a reproducible, controlled roughness substrate. However, the laser engraving method produced surface features that were much greater in scale than the particles. These scale differences were such that the substrates produced were not of value to this research. The second option investigated to induce reproducible substrate roughness was to scratch the glass disk using sandpapers of known grain size. A third approach to establish reproducible roughness was to use fine stainless-steel wire mesh substrates. In tests with sanded glass disks, the interfacial energy of plasma-cleaned (hydrophilic) glass beads had a high variation at 40% RH, showing non-uniformity of area of contact between particles and substrates. As the RH increased, it was expected that the interfacial energy of hydrophilic particles would increase, but this behavior was not observed. In addition, comparing the interfacial energy results of hydrophilic particles with hydrophobic particles, a region with significant interfacial energy difference was not identified. In the case of the stainless-steel mesh substrate, the mesh asperities and particle dimensions were comparable. Thus, the smaller particles had more area of contact with the substrate than the larger particles. For the plasma-cleaned (hydrophilic) beads, the recovery values had an average of 92.5% recovery when the RH was between 46 and 85%. For the hydrophobic beads, the average recovery was 19.0% when the RH was between 46 and 75%. Thus, the hydrophobic characteristic of the particle influenced its lower interaction with the mesh substrate. The difference in recovery can be exploited to achieve separation of particles based upon adhesive forces.

Nov 30, 2021

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By Jacques Magnaudet, Julie Cranga, Didier Huin, Pascal Gardin

"With the aim of controlling steel grade in steelmaking reactors, IRSID and IMFT are developing a numerical description of the evolution of bubbles in the vicinity of a liquid steel/ slag interface. The objective is to identify the main parameters affecting the hydrodynamics of the various phases. The goals of the present paper are:• To describe the numerical technique developed to predict the multi phase flow including bubbles, liquid metal and slag layer.• To analyze the influence of the absolute pressure on the bursting of bubbles in a RH degasser. Validation is given by comparison with results available in the literature. The major point concerns the distinct behaviors observed whether the pressure is low or high.• To study the influence of the properties of the slag layer (thickness, viscosity and interfacial tension) on the entrainment of liquid metal in the wake of the bubble and on the nature of the projections from the bath surface.IntroductionMost of secondary steelmaking processes use gas stirring for homogenization, removal of nonmetallic inclusions or decarburization under reduced pressure. The bursting of gas bubbles at the metal or slag layer surface produces a beneficial ejection of metal droplets in the low pressure atmosphere, provided that there is no violent projection, which may have detrimental effects on the process.Our objective is to develop a numerical tool to study the phenomena occurring in the vicinity of the bath surface, in particular bubble bursting under reduced pressure and entrainment of metal in the slag layer. In this paper we report the first conclusions of our study. In the first section we describe the numerical model used to describe the three-phase flow and the expansion of the gas bubbles under the effect of the ferrostatic pressure. The second section is devoted to the study of pressure effects on bubble rise and bursting. The third section reports some computational results about the rise of a gas bubble through the interface between the two liquids."

Jan 1, 2001

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013

By Xiaobo Zhang, Panshi Xie, Xiaobo Wu, Ding Lang, Jiandong Yu, Yongping Wu, Kun Feng

In a fully mechanized top coal caving mining process, the mechanical properties of the top coal deteriorate constantly, and the stability of the support is determined by the boundary position of the top coal entering the limit equilibrium state. Top coal flaking occurs more easily along the advancing direction owing to an increase in the distance of the boundary from the wall. Moreover, the strength of the coal seam is an important factor that determines the boundary position. The equation of the top coal limit equilibrium zone boundary, used in fully mechanized top coal caving mining, was determined based on the limit equilibrium theory, continuum damage mechanics, and the Hoek–Brown rock empirical strength criterion. Using the RFPA3D and UDEC numerical analysis methods, the effect of top coal strength on the mechanical behavior during the mining process was determined; and the space–time relationship between the top coal deformation failure, damage evolution, and boundary of the limit equilibrium zone was established. The results revealed that when the coal mass entered the limit equilibrium zone, accelerated crack development, accelerated damage, and axial unloading occurred. Moreover, an increase in the coal seam strength caused the boundary of the top coal limit equilibrium zone to be closer to the wall. By comparing the numerical results with the theoretical results, the overall trend was found to be consistent, allowing the verification of the rationality and reliability of the determination equation of the boundary position of the limit equilibrium zone.

Sep 21, 2021