Search Documents

By R. B. Snow

THIS paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents-lime (CaO), tricalcium silicate (3CaO•SiO2), dicalcium silicate (2CaO-SiO2), monticellite (CaO•MgO-SiO2), or forsterite (2MgO•SiO2), with especial emphasis on the mineral merwinite (3CaO-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, "FeO," MnO and SiO2, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as aluminates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + MgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO2 is more than 2 to r. When sufficient lime is available it combines with the silica to form dicalcium silicate (2CaO•SiO2), which contains little, if any, MgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2CaO•SiO2) it combines with MgO to form either merwinite (3CaO•MgO.2SiO2) or monticellite (CaO-MgO•SiO2); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and MnO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as CaO-MnO•SiO2 and CaO-FeO-SiO2 are found only in slags in which the lime-silica ratio is less than 2 and are not observed in specimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of opaque or colored constituents. The indices of retraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3CaO•MgO.2SiO2) from its optical properties is usually difficult in the presence of dicalcium silicate (2CaO•SiO2). CaO, MgO, 3CaO•SiO2 and 2CaO•SiO2 in open-hearth slags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1947

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By Peter M. DiGiacomo

In situ leaching technology requires information about how injected fluids flow in the rock in relation to the localization of the valuable minerals to be leached. In oxidative leaching of sulfide copper ores, flow channels can be determined by the observation of residual iron oxides. In contrast oxide copper ores do not leave a detectable residue after leaching. Method is developed that allows a selective labeling of the leach residue with fluorescent compounds. The fluorescent zones can be detected in corings after the leaching operation.

Jan 1, 1981

By Mike de Wit

Of the approximately 6,500 kimberlites known to date, less than 3% are diamondiferous and less than half of those are economically viable. Admittedly, this is a global figure and varies from area to area much depending on geological, logistical, and political circumstances. The number of diamond-bearing kimberlites is an important geobarometer, and an age-frequency profile has been compiled in order to identify diamond metallogenic epochs and provinces. Four primary diamond clusters have been recognized: Siberia (332-370Ma), Kaapvaal South(114-144Ma), Kaapvaal Southwest(84-95Ma), and Slave (52-55Ma). In addition, three secondary clusters are the Kaapvaal Central (S06-S38Ma), the Man Craton (139-lS3Ma) and the Kasai Craton (120-130Ma). The Kaapvaal is the only area where kimberlites with diamonds were discovered between 1870 and 1925, except for the Prairie Creek discovery in North America in 1906 and Colossus in Zimbabwe in 1907. Between 1906 and 1940 no major diamondiferous kimberlites were discovered, but many of Africa's alluvial deposits were found and exploited in that period. Advances in scientific prospecting in the 1940's rapidly accelerated the discovery rate that peaked in the 1990's; 39 diamondiferous occurrences were found in the 1980's, of which 8 became mines and 5 are in feasibility, and nearly 450ha of kimberlite was added to the global resource base. Despite the accelerated exploration expenditure, the last decade (e.g. 2000-2009) has been the leanest since the 1940's. The most important reason for this decline in exploration success is that any undiscovered deposits are largely buried by younger cover. Understanding complex and geophysical noisy basement geology, as well as decomposition of path-finder minerals are major challenges to further exploration success. Major investments in basic geological expertise and field research will have to be made in order to secure future diamond resources. Integrated geophysical studies, geochemistry diamond forensics, and improved imaging of Earth's upper mantle are perhaps foremost in this requirement, but the costs of these activities are such that government support will be required if countries are to sustain their diamond mining industry.

Jan 1, 2010

By L. I. Kiss, A. Larouche, V. Dassylva-Raymond

Control of the quenching capacity of the cooling water is of primary importance for maintaining the quality and recovery rate of ingots produced by direct chill casting. Industrially, this can be done using a cylindrical metallic probe undergoing rapid quenching by direct immersion in a reservoir filled with casting water. Such a test rig originally developed at Alcan Arvida Research and development Centre was modified and used to assess the role of key parameters affecting the boiling heat transfer. During the tests, the probe of the instrument undergoes the effects of different heat transfer mechanisms. An experimental study was performed in order to clarify the details of the probe-water heat transfer during rapid quenching. The heat flux along the surface was determined by mathematical modeling using the measured temperature signals, while the corresponding heat transfer regimes like stable and unstable film boiling, nucleate boiling and natural convection were identified by the analysis of high-speed video recordings. Aluminium

Jan 1, 2006

By Dan W. Bench

PCBs are hazardous not only to human health and the environment but also to the mining industry because of potential worker exposure and improper disposal liabilities. In this sense, the paper point out the identification, management, and proper disposal of pcb-containing electrical equipment used in mines. Also it point out alternatives to PCB dielectrics, storage, and disposal. The use of PCBs in mines has been documented during U.S. Environmental Protection Agency Region 8 mine inspections and it used as dielectrics in transformers, capacitors, and fluorescent light ballasts are common throughout industry worldwide.

Sep 14, 2009

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy These microorganisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation. These extreme thermophiles are Archae, characterised by a different cell envelope structure perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathways.The active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity.In this paper, we report on studies carried out to quantify the ability of the extreme thermophile Sulfolobus to withstand the hydrodynamic stress environment generated at high pulp densities in the slurry bioreactor. Both a pyrite system (as a model system) and a chalcopyrite system (as an application) were studied. In laboratory reactor systems, the nature of biological responses to stress induced at high pulp density have been identified in terms of ability of the microbes to grow, their metabolic activity and rate of leaching and cell integrity. Critical operating conditions within the laboratory reactor are identified and the mechanism mediating reduced performance considered."

Jan 1, 2003

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR&apos;s Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

This study applies a machine-learning technique known as multiclass logistic regression on a 10-year injury dataset from the U.S. Mine Safety and Health Administration (MSHA) to determine miners’ susceptibility to injury and to help identify significant risk factors associated with different classes of injury. The analysis identifies specific risk factors that influence a mineworker’s susceptibility to a given class of injury: nonfatal with no days lost or restricted activity; nonfatal with days lost and/or days of restricted work activity; and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal versus noncoal), experience on the current job (years), shift start time, employment type (operator versus contractor), mining district and type of accident. The results of the analysis indicate that a miner’s experience on the job (the number of years worked in a current job) is a significant risk to injury occurrence, even for those with decades of total mining experience.

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By Joklik, G. F.

Most publicity about the copper industry nowadays is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and potential shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today&apos;s rapidly changing technology. Copper differs from other widely traded commodities in that its real cost of production has progressively increased since World War 11. The reasons for the increase are identifiable by analyzing operations in one of the world&apos;s large producing centres, the copper province of Arizona. Another respect in which copper differs from some other commodities is that increases in demand occur less automatically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry&apos;s current inability to generate and attract needed investment capital is attributable to these differences between copper and other commodities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on circumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of producing and manufacturing facilities in industrialized nations like the U.S.; and consumer-oriented research and marketing by the copper producers.

Jan 1, 1978

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project&apos;s major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

By J. S. WARWICK, E. J. Browning

Ignitions continue to occur underground, sometimes leading to major explosions. There has been considerable effort in the UK, and more widely in the European Community, to formulate the best ventilation practices and other means of minimising these incidents. Practices and procedures to prevent ignitions are discussed in the light of the risks from current mining methods.

Jan 1, 1993

By Milton Manrique

The thermal decomposition of ilmenite concentrates in a non-transferred arc; thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and particle size was studied. Products were characterized by XRD, SEM, TEM and ICP techniques. Free energy minimization plots were used to predict the thermodynamic behavior of the system under different operating conditions. The results of this investigation showed a significant segregation process where titanium-rich products are collected in the reactor, while iron-rich products are collected in the quenching box and filter. The average size of the product is in the sub- micron range. Titanium nitride was formed and condensed in the reactor zone when using an argon-nitrogen mixture as the plasma gas.

Jan 1, 1998

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994