Search Documents

By R Carreau

The results of a detailed acid rock drainage (ARD) prediction program were used to revise the waste rock segregation criteria at the Restigouche open pit mine. Waste rock at the site was predominately derived from altered volcanic rocks that hosted a massive sulfide lead/zinc orebody. The program assessed the five years of drainage chemistry from both the potentially acid generating and the non-acid generating waste rock storage facilities in addition to laboratory-based kinetic test results. Material-specific leaching characteristics including relative metal-release rates and neutralisation potential depletion rates were determined from 12 laboratory-based kinetic tests. Solid-phase analyses indicated that, although pyrite was typically the most abundant sulfide mineral in the waste rock, its abundance varied significantly as documented by total sulfur contents ranging from 4.0 per cent. Kinetic test results were used to establish revised waste rock segregation criteria based on total sulfur content and neutralisation potential. The revised criteria maintain that waste material with a total sulfur content 4.0 per cent as potentially acid generating. When present in sufficient quantities, ankerite provided an effective source of neutralisation potential for the range of observed sulfide oxidation rates. Kinetic testing documented that up to 6 kg CaCO3/t was ineffective at neutralising acidity in samples that contained >4 per cent S. The carbonate molar ratio measured from the humidity cells was adjusted to reflect the stoichiometry of the ankerite and applied as an NP/AP criteria for waste rock containing 0.1 <S per cent <4.0.

Jan 1, 2003

By H Barrie, L Ameglio

"Current methods for acid rock drainage (ARD) mitigation revolve around insulation of the waste from oxygen in the atmosphere with water and dry (soils and liners) covers. Both are of limited effectiveness and present significant drawbacks. Furthermore, while they reduce oxygen influx, they reduce but do not prevent ARD.The inert gas mixture (IGM) technology has been designed to overcome the deficiencies of gas transfer into tailings and waste rock materials across the surface and instead block oxidation by controlling the transfer of oxygen from the atmosphere. Inert gas is injected into the mine waste at low flow rates and the positive but low flow purges the oxygen that tends to diffuse into the sulfide waste across the surface. The positive flow of IGM compensates for inward oxygen diffusion and creates a pressure drop across the cover layer preventing inward diffusion of oxygen and, hence, acid generation.The IGM processes are evaluated in this paper: theoretically, with a review of the theory of ARD and the current state of knowledge about the performance of notably dry covers as atmospheric oxygen barriers via models to predict the performance of the IGM technique practically, with a bench-scaled experiment.The results demonstrate the effectiveness of IGM to prevent oxidation of sulfide minerals and ARD in waste rock. The laboratory experiments further identified key variables to be used to monitor performance and control efficiency of IGM, which is now awaiting field-scale application.The IGM technology is a patented process by Terraquest Technologies Ltd (Canada) in USA, Canada and Australia. The IGM technology can be cost-effectively manufactured on-site with commercially available compressors and gas filtration membranes. It is predicted that low-cost covers can then be utilised with IGM, which in turn lowers the overall capital costs of ARD mitigation.CITATION:Ameglio, L and Barrie, H, 2015. Acid rock drainage prevention using inert gas mixture technology, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Paul Pajunen, Michael Sheedy

"Acid separation using short bed ion exchange is a now well established technology in copper refinery tankhouses. Refinery bleed streams from liberator cells are treated by short bed systems to produce an acid-free byproduct stream that contains the bleed metals and valuable nickel salts. Removing the acid eliminates the need for a black acid evaporator and reduces the amount of sodium carbonate required in nickel selective precipitation processes. The recovered sulfuric acid can be recycled to the tankhouse. This same technology is routinely used to treat other acids such as hydrochloric, nitric, and hydrofluoric. In the case of hydrochloric acid, the process can selectively separate chloro-anionic complexes such as Zn, Pb, and Cu, which are then eluted with water. The acid recovery technology can also be closely coupled with ion exchange processes in order to minimize regenerant acid consumption. In many hydrometallurgical applications resin regeneration often requires an acid dosage multiple times the stoichiometric minimum. Coupling an acid recovery bed with the IX column allows recovery and recycle of the free acid in the spent regenerant, thus reducing the overall acid consumption to just slightly more than stoichiometric.Short Bed Ion ExchangeThe short bed ion exchange process has been extensively used in the metal finishing industries since the early 1970s [1,2]. Short bed systems have also been sold to primary metals producers for the separation of sulfuric acid from copper refinery bleed streams [3] and for the recovery of nickel and cobalt from plant effluent streams. This unique technology optimizes the ion exchange process and offers a number of significant advantages over conventional ion exchange. The principal features and benefits of this technology are presented below."

Jan 1, 2012

By M. Gomo, L. S. Mokhahlane

"Underground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for electricity generation. Residue products from UCG have the potential to leach into surrounding groundwaters. The geochemistry and leaching dynamics of these products are explored in this study. The products include char, ash, and the heat-affected zone in the surrounding rocks. Core samples from the pilot plant at Majuba are the first ever to be recovered from a UCG cavity in Africa, and they give key insights into the geochemistry of the gasification zone. Mineralogical and chemical analyses were performed on the samples, and acid-base accounting (ABA) was used to predict the acid-producing capacity of the gasification zone, particularly for char samples. Some of the char contained pyrite, although not all samples were acid-producing as determined by the ABA analysis. The ABA results showed that some of the unburned coal has moderate levels of sulphur, which could be the driving medium for acidic conditions. The ABA analysis indicated that water in contact with the gasification zone would eventually have a pH lower than 7, which could lead to acid rock drainage. These results form part of a preliminary investigation into the geochemistry of the reaction zone, post gasification. IntroductionUnderground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for industrial purposes, including electricity generation. The gasification process leads to the formation of a cavity composed of char, rubble, and void space (Bhutto, Bazmi, and Zahedi, 2013). Residue products from UCG have the potential to leach into groundwater. These products include char (devolatilized coal), which can generate acid rock drainage (ARD). ARD is caused by the oxidation of sulphide minerals, which acidifies the leachate, thus increasing the solubility of some environmentally toxic metals (As, Cd, Hg, Pb, Zn, etc.) (Bouzahzah et al., 2015).The main source of ARD is oxidation of sulphide-bearing minerals due to interactions with oxygen, water, and microorganisms (Simate and Ndlovu, 2014; Kefeni, Msagati, and Mamba, 2017; Bouzahzah et al., 2015). Although ARD occurs naturally, it can be enhanced by mining activities that escalate exposure of sulphide minerals to water, air, and bacteria (Simate and Ndlovu, 2014). At the Majuba pilot plant, the unburned coal remaining in the cavity has been in contact with groundwater since the gasifier was shut down in 2013. It is possible that in a commercial UCG plant, most of the coal will be consumed and no unburnt coal will be left in the cavity. Most of the sulphur will be converted to H2S during the gasification process and transported with the syngas to surface, where it can be removed and captured as elemental sulphur."

Oct 1, 2018

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By R. J. Pugh

In addition to directly analyzing the surfaces of minerals using high vacuum instrumentation methods, some important surface properties of mineral fillers can be determined indirectly by using reactive chemical probe molecules. This technique enables the strength and the number of the surface reactive sites to evaluation and this type of information is useful in predicting interfacial behaviour of minerals. One method of classifying these surface sites is by using Lewis acid/base theory and this type of approach could enable one to predict the adsorption of functional groups in dispersants, thickeners, pigments, etc. Also the adhesion of polymer matrices to the filler surface may be improved.

Jan 1, 1992

By J Millard, K Sexsmith

BHP Billiton Diamonds Inc (BHPB) has been mining kimberlite from several pipes at the Ekati Diamond MineTM located 300 km north of Yellowknife since 1997. Processing of kimberlite produces coarse kimberlite rejects (CKR, 0.5 to 8 mm) and fine tailings (less than 0.5 mm). The CKR are trucked to the Coarse Kimberlite Reject Storage Area (CKRSA) located within the drainage area of the tailings impoundment (Long Lake Containment Facility û LLCF). The coarse rejects are wet when dumped and are expected to freeze as a result of annual average site temperatures of about -10¦C. Seasonal thawing occurs along the exposed edges of the pile. Monitoring of the CKR indicates they have consistently low sulfur concentrations (0.4 per cent) accompanied by high acid neutralisation potentials (78 to 337 kg CaCO3/t). Carbonate concentrations vary from 0.9 per cent to 3.4 per cent. The CKR are therefore not potentially acid generating based on conventional laboratory testing. Monitoring of stagnant pools on the tundra downgradient of the CKRSA has shown that water originating from the pile resembles acid rock drainage (ARD). Water pHs can be less than 4, and sulfate concentrations are typically in the thousands of milligrams per litre. Conventional flowing toe seeps are pH neutral but also have elevated sulfate concentrations. Investigations conducted in the summer of 2002 revealed no evidence of in situ acid generation. Pore water chemistry is probably controlled by oxidation of fine-grained pyrite, neutralisation of acidity by calcium and magnesium carbonates and silicates, and freeze concentration of pore water. The acidity observed in tundra pools downgradient of the CKRSA appears to be a result of leaching and mobilisation of iron under reducing conditions at the CKR-soil contact. Downstream of the CKRSA, reduced iron oxidises and is hydrolysed on contact with the atmosphere causing pH depression. BHPB is applying the findings of this study by constructing facilities containing kimberlite on granite pads. These in turn are placed on frozen ground so that the foundations remain frozen and limits contact of wastes with the acidic soils.

Jan 1, 2003

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania). The results were confirmed by means of beneficiation tests on various types of ores, from the Kukes (Kalimash), from Bulquiza area and from the Rizo deposit (Greece). It has been demonstrated that when Na-K Oleate is used as collector chromite, olivine and serpentine can be separated at pH = 2.5 and/or 5.5 employing EDTA (EthyleneDiamineTetraAcetate) on previously deslimed material. This approach ensures flotation concentrates with a Cr2O3 content about 50%, at a recovery in excess of 65%.

Jan 1, 2003

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

By H. V. Fairbanks

It is estimated that millions of tons of coal fines are unsaleable each year due to difficulty of drying them economically with conventional mechanical dewatering and thermal drying equipment. The difficulty is due to the fact that coal of small particle size presents a large surface area with polar groups which have a great affinity for water. In order to remove this water thermally, a high temperature is necessary which oxidizes the surface of the coal. This substantially reduces the heating value of the coal. If drying could be satisfactorily carried out at a lower temperature, much more of the heating value of the coal fines could be retained. It was conjectured that acoustic energy applied during the drying process might prove to be of value since acoustic energy has the property of producing cavitation at a liquid-solid interface when the intensity is sufficiently great. This cavitation process produces water at room temperature which can be carried away from the solid surface by a flow of relatively cool air. Hence, moisture removal is made possible at a lower temperature.

Jan 1, 1966

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

Oxidative alkali roasting of chromite is the state-of-the-art process for manufacturing chromium-containing chemicals, which involves dealing with serious environmental problems arising from handling Cr6+-containing wastes generated in this process. In this article a new method for the extraction of Cr2O3 from chromite ores is explained, based on the carbothermic reduction of concentrates in the presence of alkali investigated in the temperature range of 950–1050 °C. Under these conditions, the iron oxides present in the ore body are reduced to metallic iron and the resulting separation of chromium occurs by forming sodium chromite (NaCrO2). The reduced samples are magnetically separated for the recovery of an iron-rich fraction, and a non-magnetic fraction containing NaCrO2, MgO and other impurities. The further treatment of the non-magnetic fraction by leaching yields a Cr2O3-rich product of approximately 85% purity, with remaining alumina, alkali and magnesia. The main advantage of the process is that, under reducing atmosphere and subsequent leaching conditions, the oxidation of Cr3+ to Cr6+ is completely avoided; thereby decreasing the risk of land, air and water pollution.

Mar 1, 2017

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By Rina Kim

The addition of lead to a gold leaching reactor can effectively accelerate or retard the gold cyanidation reaction. This study explored the effect of lead on the gold dissolution kinetics using cyclic voltammetry (CV) experiments. It was illustrated that the gold leaching kinetics in the cyanide solution enhanced with the addition of lead salt in the low overpotential region (–0.35 V vs. Ag/AgCl). The similar behavior was observed in the presence of ore containing 0.25% galena. In contrast, the gold oxidation kinetics retarded at –0.35 V (vs. Ag/AgCl) in the presence of silicate and lead-bearing mineral under certain conditions. Likewise, the lead addition was not functional for the high sulfur ore. This was attributed to the oxidation of the sulfides to the elemental sulfur, which subsequently formed a passivating layer on the gold surface. The results were evidently affirmed by the electrochemical tests and X-ray photoelectron spectroscopy (XPS) analysis.

By K. N. Subramanian, H. Kanduth

"It is well known that chalcopyrite can be dissociated into simple sulphides by heating with elemental sulphur at about 475°C:CuFeS2 + S -> CuS + FeS2Experimental work was undertaken to determine whether this ""activation"" could be used to advantage in the selective leaching of copper from chalcopyrite concentrate.A method of treating copper concentrate with molten sulphur was developed and the activated product was leached in dilute sulphuric acid using oxygen, ferric iron or manganese dioxide as the oxidant. The object was to obtain a solution suitable for electrowinning with minimal purification, but it was impossible to obtain rapid extraction of copper without simultaneously dissolving a large proportion of iron. This was attributed to the fact that some of the copper was present as a low iron-copper sulphide (idaite) and that the pyrite formed during the ""activation"" step was more easily oxidized than natural pyrite."

Jan 1, 1973

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016