Search Documents

By M. R. Geer, H. F. Yancey

Four coals were treated in the Humphreys spiral concentrator, and the products were examined by float-and-sink and screen-sizing tests to determine fundamental performance characteristics. The efficiency of the separation between coal and impurity was shown to be influenced greatly by particle size.

Jan 1, 1950

By Whitman E. Brown

The installation in 1948 of a Humphrey spiral concentrator section at the Hill-Trumbull plant of The Cleveland-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus 1/8 in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 44 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus 1/8 in. size. After desliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant.

Jan 1, 1949

By James A. Robertson

"In the Blind River area Proterozoic clastic and sedimentary rocks and minor volcanic rocks (The Huronian Supergroup) uncomformably overlie and trangress northwards over dominantly granitic Archean terrane (2500 + Ma) and are intruded by Nipissing Diabase (2ll5 Ma). Later deformation and metamorphic events are recognized. The developing depositional basin was controlled by the incipient Great Lakes Tectonic Zone marginal to the Algoman Craton.The Matinenda Formation (basal Huronian) comprises northwards-derived fluvial arkose, quartzite, and pyritic, uraniferous oligomictic conglomerate which contained in 1981 some two-thirds of Canada's uranium resources. Production to December 1981 from Elliot Lake totalled 98.3 thousand tonnes U for an average recovered grade of 0.1% U with an additional 671 tonnes U recovered by leaching at Agnew Lake. The remaining resources are at lower grades. Some thorium and yttrium have been produced. Minor amounts of gold reflect the paucity in the source area. Gold is better-developed in the Huronian north of Sudbury reflecting the local source area.The conglomerate beds lie in southeasterly-striking zones controlled by basement topography down sedimentation from uraniferous Archean granite. Uraninite textures, the distribution of monazite, and local enrichment by reworking indicate a syngenetic, probably placer, origin of the mineralization. ""Brannerite"" has formed by solution of uranium from the margins of the uraninite grains and redeposition on the original titaniferous minerals. Penecontemporaneous volcanics may have been a source for sulphur in some of the pyrite and of trace amounts of Co, Ni and Au. Some pyrite may be detrital, some may be authigenic and some introduced.Drab coloured rocks, uranium and sulphide mineralization, the presence of hydrocarbon (thucholite) and a post-Archean regolith formed under reducing conditions have been cited as evidence of an early Precambrian reducing environment extended to the atmosphere. Sedimentary features indicating fast-flowing water and possibly a cold climate imply that the uraninite would be exposed to whatever oxygen was present in the atmosphere under conditions which would inhibit complete solution. In the upper Huronian, red beds and in the Lorrain Formation a monazite - iron oxide assemblage and copper mineralization indicate more oxidizing conditions. . Similar uranium deposits occur at Agnew Lake and in the basal Huronian north of Sudbury there are minor uranium and gold values.Provenance, lack of complete oxidation, transportation and depositional processes, redistribution during diagenesis and possibly low grade metamorphism, and the lack of post-depositional destructive processes are the dominant factors in the formation and preservation of the ores. The modified placer theory of genesis is well entrenched and an exploration model for such deposits throughout the world is well-documented.Research continues on mineralogy and textures of the ores, detailed sedimentology of the ores and their host rocks, with particular emphasis on: provenance area, the influence of early Precambrian mineralization patterns on the mineralization present in the Huronian both in space and in time, fluvial sedimentation and diagenesis. Expansion and reopening of the mines of the Elliot Lake camp should facilitate further studies."

Jan 1, 1986

HW Process Technologies, Inc. (HWPT) has developed a patented membrane-based ion fractionation system, which specifically separates copper from gold and silver species in a cyanide matrix. This Engineered Membrane Separation (EMS?) system was pilot demonstrated on the 82,000 liters of pregnant leach solution' (PLS) generated from tailings, via thin layer leaching, at a mine site in Durango State, Mexico. The EMS? recovered ~90% of the gold-silver cyano-complex to a 90% volume permeate (based upon an EMS? feed stream of 100% volume) while rejecting -90% of the copper cyano-complex to a \0% (by volume) concentrate. The EMS? technology combines pore-size specific electro-statically charged membranes with engineered materials of construction and application-specific operational design that reject multi-valent, ionically charged species to the concentrate and transmit mono-valent species through the membrane to the permeate. The 850 ppm Cu PLS contained approximately 0.8 gil free NaCN with, the copper cyano-omplex principally in the CU(CN)3 and CU(CN)4 forms. The gold grade of the PLS was -2 ppm Au. The ~LS calcium concentration at -700 ppm Ca was reduced to ISO ppm.Ca (± 50 ppm) by sodium cycle ion exchange pre-treatrnent prior to EMS? processing.

Jan 1, 1998

By Shanlu Yang

In this study, laser-GTAW hybrid welding was used to the lap joint of galvanized dual-phase (DP) 980 steel in a gap-free configuration. The effects of welding parameters such as the laser power, the distance between the laser beam and the electrode torch, the arc current on the quality of hybrid welds were fully studied. The reason for the formation of different weld defects arises from the development of the highly-pressurized zinc vapor at the interface of two metal sheets. Experimental results demonstrated that the elongated molten pool introduced by the GTAW can suppress the formation of spatters to some extent. However, the hybrid laser-arc welding process still suffers from a large amount of spatters that degrade the weld quality. Furthermore, it was found that the weld quality was enhanced with the increase in the laser beam-arc distance and welding current.

Jan 1, 2009

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021

By Michel Carreau

Renewable assets have large upfront capital costs but minimal operating expenses over their lifetimes. In some instances, deals can be structured so that direct capital investment is feasible, with paybacks typically within 5-7 years. In others, the burden of renewable CAPEX must be removed in order to create an attractive alternative to fossil-fuel-fired generation. Hatch has designed and oversees the construction of a renewable installation, which is financed, owned and operated by a special-purpose entity. Renewable energy is then delivered to the mining company via a customized power purchase agreement at a price that is lower than the levelized cost of fossil fuels. In this way, the mining company removes the burden of the renewable energy CAPEX from its balance sheet, thus freeing up capital, decreasing risk, and making the predictable, lower cost of renewable power more attractive than the variable cost of fossil fuels. This paper presents the above business model and success stories of hybrid power at remote sites (wind and solar coupled with diesel engine).

Aug 1, 2013

By Maryam Motamed, Jeremy Stone, Leigh Anne Zhang

Controlling and predicting ground movements are essential to the design of shoring systems. The Courthouse Commons tunnel in San Diego, California, included a 56-foot-deep temporary shaft as a launching point for tunneling using the Sequential Excavation Method (SEM). The rectangular shaft was unique in that it was surcharged on one wall by an 11-story building and employed a hybrid support of excavation design. An array of geotechnical instrumentation was used to monitor lateral and vertical movements at the ground surface. This paper compares the measured ground movement with the predicted ground movement from various excavation stages

Dec 1, 2022

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By D. L. Millar

The hydraulic air compressor (HAC) is driven only by water, held up by a dam, to create relatively low head (typically 10-20 metres), such that the developed hydropower is used to cause flow in openings deeper underground. Air is entrained in the water at the inlet to the sub-surface openings (an air to water volume ratio of 1:1 is reported to be optimal) and is compressed as it is carried along by the deepening water flow. At depth, and with lower water velocities arising from larger cross sectional area tunnels, air bubbles separate out of the water flow and are collected in a receiver space above the flowing water. Water, free of air, then passes back up a return shaft (up-pipe) and rejoins the river or stream flow. In principle, an HAC can produce any pressure and flow rate required, given large enough shafts and enough water supply with head sufficient to overcome frictional resistance in the sub-surface tunnels. Practically, as air solubility in water increases with pressure, HAC installations with depths greater than 100 metres may lead to higher rates of compressed air loss, without special separation measures. A modern HAC application for mine refrigeration and cooling is presented.

Aug 1, 2013

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

By Nigel Fung, J. D. Humphrey, R. H. Oats, J. H. Ingle

Production dozing of cast material is a cost effective method of improving dragline or mobile equipment overburden removal. Yet dozer productivity is reduced during the part of the process that requires the dozers to cut material away from the highwall. One solution is to use a hydraulic excavator to remove this material and throw it into a windrow for the dozers. By freeing up the dozers for more productive work the overall system productivity increases 25% and cost per yard is reduced by up to 10%. Dozer fleet sizing can be determined to match a specific production schedule or can be sized to balance with an excavator’s production.

Jan 1, 2004

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021