Search Documents

By E. H. Sellards

ON Oct. 9, 1929, a sink formed in the Sour Lake salt dome oil field in Texas, and on Oct. 12 a second smaller sink formed at the north margin of the first. The purpose of this paper is to give such observations as it has been possible to make on the earth movement incident to this subsidence. Sour Lake salt dome is typical of the salt domes of the Gulf Coastal Plain of Texas. Structurally the dome is a plug of salt which rises to within 900 ft. or less of the surface. Above the salt is a cap rock consisting of anhydrite with more or less calcium carbonate. The salt plug, as contoured on the cap rock, is circular in outline with, however, some appreciable irregularities. Overlying the cap rock are relatively uncompacted sediments consisting of sand, clay and gumbo.. At the crest of the dome these deposits are no more than 700 or 800 ft. thick. However, the sides of the dome are steep, and the sediments thicken rapidly away from the crest. The sink formed about 1500 ft. northeast of the crest of the dome where the sediments overlying the cap rock are from 1000 to 1200 ft. thick. The cavity permitting the subsidence was quite certainly either in the cap rock or in the salt below the cap rock, so that the sink was formed by the caving of as much as 1000 or 1200 ft. of earth.

Jan 1, 1930

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

This paper presents a rationale for selecting appropriate support elements which combine to form a support system to maintain stability in mines subjected to both strainburst and the shaking that occurs from fault slip. The overall approach was developed during the 'case for safety' study undertaken to allow the then Beaconsfield Gold mine (now Tasmania mine) to resume development and production after the 25 April 2006 ground-fall and fatality that received worldwide publicity. Issues of the sometimes competing requirements of support element performance during dynamic loading are discussed and the need for support flexibility is contrasted with the usual high support element stiffness required when these are used to reinforce rock masses. An example is presented to show the steps and technical details required to design each component of a support system to counter the de-stabilising effects of seismicity.

Nov 25, 2010

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By J. Patrick Powers

In tunneling through water-bearing formations, the expense of controlling the water can have a major impact on overall project cost. The author has seen the cost of an eight-foot, finished sewer tunnel rise from under $500 per foot to over $1,000 when a water problem, anticipated as modest, became severe. There is need for greater professionalism in the approach to groundwater control. The days of the forked stick should be behind us. The basic technology exists. Its application is not yet widespread. This paper discusses predrainage; that is, the lowering of water in advance of tunnel excavation. Both free air and compressed air tunnels are considered. Examples from recent tunnel projects are described. SPECIAL NATURE OF TUNNEL DEWATERING Tunneling is unlike other excavations below the water table in a number of significant ways. The tunnel excavation is always on the critical path; if production slows or stops, there is no other work for the heading crews, no other work to carry the cost of service crews and job overhead. The dewatering commitment must be made well in advance. Construction of wells, and pumping down take time. After the heading reaches a trouble area, time is not available

Jan 1, 1997

By J Sigda, T Jones, D Staggs, J Ewing, C Cheng, J Pickens, S Paulka

Mine-derived solutes from Energy Resources of Australia’s (ERA’s) Ranger uranium mine have been closely monitored for decades. Ranger is surrounded by the Northern Territory’s Kakadu National Park and is upstream of Ramsar convention wetlands. Modelling of groundwater flow and solute egress from mine wastes to surface waters has helped ERA successfully assess closure options and secure intermediate regulatory approvals during the site closure process. Potential environmental impacts were assessed using groundwater modelling in support of three ERA applications involving disposal of tailings-derived mine waste. Model results were an important part of the basis for obtaining regulatory approval. Three case studies are presented describing the three applications and how the groundwater modelling supported approval of the applications. For case study #1, INTERA supported ERA in addressing stakeholder concerns in 2017 regarding two aspects of tailings deposition in Pit 3. The first was the potential for flow of tailings fluid into the surrounding formations during tailings deposition. The second was the difference in post-closure magnesium (Mg) loading to surface water for two tailings deposition scenarios. INTERA developed a two-dimensional (2D) model that showed excess tailings pore pressures would not cause outflow and solute egress from the pit during deposition. INTERA’s three-dimensional (3D) models demonstrated that post-closure Mg loading to creeks for both tailings scenarios differed marginally and would be a small fraction of natural creek Mg loads. The modelling results helped avoid delays in completing tailings deposition driven by stakeholders’ environmental concerns. Case study #2 consisted of supporting ERA’s 2019 request for approval to change the tailings deposition method and final tailings level in Pit 3. INTERA’s model results for the permitted and proposed deposition methods showed minimal differences in post-closure Mg loading to creeks. The model results helped ERA obtain the needed approval for the tailings deposition method and water and tailings levels in Pit 3. For case study #3, INTERA modelled the comparative impacts from leaving the entire contaminant plume from the temporary tailings storage facility (TSF) in situ or excavating a portion of the contaminated material from beneath the TSF floor and placing it in Pit 3. The modelling results supported an approved TSF contaminated material application important for ERA to stay on schedule and minimise both closure costs and environmental impacts.

Jul 1, 2021

By John D. Nelson

Foundation underpinning is a common component of remediation schemes for distressed foundations on expansive soils. For many applications in expansive soil, micropiles have distinct advantages over other techniques. This paper will concentrate on the design and construction of micropiles in expansive soil. It discusses the nature of building distress and the relationship between foundation movement and soil heave. It presents methods for determining the factors that are required for the design of micropiles. Such factors include calculation of expected free-field heave, depth of soil wetting, and prediction of pier movement. A finite element program developed by the authors and others to determine pier heave and internal forces is presented. The input parameters that are required for pier analysis are discussed, and the nature of the output and the sensitivity of the results to the output are described. A case example illustrates the advantages of micropiles over other methods.

Aug 1, 2013

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC), as agent for Phillips Petroleum Company, Sohio Shale Oil Company, and Sun Shale Oil Company, is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub, located in northeastern Utah and known as the White River Shale Project (WRSP). The Ralph M. Parsons Company (Parsons) has been retained as the design engineer/constructor for the project. This paper covers the successful pregrouting of the Bird's Nest Aquifer in conjunction with the sinking of a 9.2-m (30-ft)-diameter shaft and driving of a 3.89-m by 5.64-m (18.5-ft by 12.75-ft) decline. The Bird's Nest Aquifer derives its name from the ellipsidal solution cavities caused by leaching of random-size nacholite nodules. The sodium bicarbonate nodules occur as persistent bands within a matrix of siltstone and marlstone. The team, made up of the owner, engineer/contractor, and subcontractor successfully grouted the shaft down to an inflow of less than 0.06 lps (1 gmp) and the decline down to less than 0.12 lps (2 gpm) by injecting a total of 213.190 kg (470,000 lb) of Celtite Terraseal, 113,400 kg (250,000 lb) of limestone dust, and 41,730 kg (92,000 lb) of cement into the formation.

Jan 1, 1985

By Oliver Bololes

UNDER the able leadership of Samuel H. Dolbear, the Committee on Nonmetallic Minerals furnished a program of sixteen papers comprising three sessions. An outstanding accomplishment in technology presented at the first session by Benjamin L. Miller and C. H. Breerwood is the application of flotation to the purification of limestone used in cement manufacture. In place of selective quarrying to provide high-grade raw material, the quarry-run stone is pulverized and treated in froth flotation cells for removal of free silica and mica. Some advantages are cheaper quarrying, more complete utilization of quarry rock, avoidance of purchasing high calcium stone, lower fuel cost and improvement in the finished cement. Paul M. Tyler presented the general subject of milling methods as applied to nonmetal lies. He pointed out the importance of some of the more recent refinements in ore dressing, and urged the need of a wider appreciation of their possibilities. The gypsum industry of Canada was described by L. H. Cole. Crystal growth during the setting process was illustrated by moving pictures. The Coastal Plain and interior salt

Jan 1, 1935

By C. I. Richman

The E h potential during of a iron reducing bacteria such as Aquaspirillum Magnetotacticum (A.M.) can be predicted by a growth model. It also reflects the adsorption of Fe+2 Cu+2 and Mn +2 ions, that can be incorporated into magnetic material called magnetosomes. The Ferric ion concentration during controlled growth of Thiobacillus Ferrooxidans (T.F.) is a function of the bacteria population curve, while A. M. ferrous ion concentration is a function of the integral of the population curve. Charting of the redox potential of T.F. during batch oxidation of refractory ores such as pyrite and pyrrhotite can be helpful to establishing onset and rate the bulk bio-oxidation rate. The onset of biooxidation is marked by an increase in Fe +3 ions that can be correlated with increased growth due to adsorbed electrons.

Jan 1, 1998

By T. W. Guy

DURING recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years-at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures.

Jan 1, 1931

By Cecil H. Desch

THE progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, deter- mining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(l)f and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By James L. Oleson, Hunter R. Propsom, Kevan J. R. Ford, Robert D. Henderson, Bob Musgrove

"Kinross’ Fort Knox Gold mine, near Fairbanks, Alaska has successfully implemented two major metallurgical continuous improvement projects resulting in growth of gold production and an extension of mine life. In 2009, Fort Knox produced 263,153 oz of gold at a cash operating cost of $543/oz. In 2010, approximately 63% of the gold will be produced from the CIP circuit, 15% of the gold from the gravity circuit and 22% of the gold from the heap leach.In 2009, a 44,000 ton per day run-of-mine valley fill heap leach facility was constructed and commissioned as a cost effective treatment option for low grade ores to supplement the higher grade mill. The heap leach facility will produce approximately 100,000 ounces of gold per year under severe winter conditions. Heap leach gold recovery, based on test work shows 30% after a 55-day leach cycle, with long term ultimate gold recovery targeted at 65%. The paper presents the heap leach design concepts and production data.Additionally in 2009, installation of a Knelson gravity concentrator unit (XD70) was completed. This together with an Acacia intense leach reactor (AILR) has increased overall mill gold recovery from 79.3% to 80.7%. A manual shaking table gold recovery operation has been replaced by batch intensive cyanidation of the high grade Knelson concentrates. Increased removal of coarse gold and difficult-to-leach gold species from the grinding circuit, via the gravity circuit, has improved gold leach recovery in the conventional whole-ore tank leach CIP circuit. The paper presents plant operating data, showing the improvements over the old flowsheet.Focus on the metallurgical properties of the high grade and low grade end components of the Fort Knox ore has resulted in significant improvement to gold recovery."

Jan 1, 2011

By Blandford C. Burgess

Mica is an orchid among minerals. It is formed in pegmatites, one of the most bizarre of igneous formations, and is exceeded by few other minerals in the perfection it may attain as to size, color, and cleavage. First used for window glazing, as an ornament and article of trade, it has become one of the most essential insulators of electricity, heat, and shock. Most internal combustion engines use mica condensers or capacitors and such machines of war as planes, tanks, and submarines are immobile without it. The original manuscript of this guide was written in April 1943 at the peak of war emergency. It was not used be- cause shortly thereafter a decision was made to buy on a one price basis eliminating differentials for both quality and size. This is now presented with the thought that from the standpoint of preparedness we can only consider an- other war imminent and every effort should he made to set up in usable form the experience gained during the Second World War. Colonial Mica Corp. was set up by Metals Reserve Co. as a wholly owned government agency to encourage production of domestic mica and to purchase it. It soon became the exclusive buying agency for such mica. The writer as Southern Manager called on all the private agencies buying mica to assist in formulating buying policies, methods, and prices.

Jan 1, 1949

With the rapidly growing use of hydraulics in mining equipment, maintenance personnel should be familiar with the various components in hydraulic systems. Hydraulic systems do wear out - the fluids they transport are hot and turbulent, the equipment they power often imposes tremendous pressure pulsations and bending stresses, and the working environment is harsh. Therefore, even though hydraulic hoses are made of remarkably trouble-free components, they do need to be replaced periodically. There must be coupling methods that allow hoses to be replaced without disturbing other components. Couplings must also provide a variety of leak-resistant connections between hoses and other components in the hydraulic circuitry. Threaded Connection and Seals Hydraulic coupling thread ends and sealing arrangements are standardized, with many types available. Their outward appearance varies, but coupling configurations are recognizable by examining threads and seals and comparing them to the examples provided here. Iron Pipe Thread There are two kinds of iron pipe threads normally used in mining equipment circuitry - National Pipe Tapered Thread for Fuels (NPTF) and National Pipe Straight Thread Mechanical Joint (NPSM). The NPTF seal is the engagement of the coupling threads, called thread interference. When tightened, the tapered thread of the male fitting binds into that tapered thread of the female fitting to form a relatively leakproof seal (Fig. 1). In the NPSM seal, there is a 30° angle seat machined into the end of the male NPTF fitting. This seat engages with a mating 30° angle cone on the inside of the female fitting. Female NPSM fittings have straight threads, as opposed to the tapered threads of the NPTF fittings. However, most NPTF solid male fittings also have a 30° angle seat enabling them to be used with NPSM female fittings (Fig. 2). JIC and SAE Fittings Joint Industry Conference (JIC) and Society of Automotive Engineers (SAE) seals are formed by joining two mating, conical metal surfaces. The coupling threads are used to bring and hold these surfaces together to form a leak-resistant seal. A JIC connection is a solid male threaded end, with a 37° machined male nose, mating with a 37° female flare seat. When connected, the mating surfaces are held together by the threads, but the threads do not form the seal. The female seat is created by flaring a tube end or machining the interior surface of a stem to 37°. A female JIC has a swivel nut, allowing the sealing surfaces to be joined together without twisting a hose or twisting the seats against each other (Fig. 3). JIC couplings are frequently used on low, medium, or high pressure hydraulic circuits on mining equipment and machinery. The SAE connection is similar in appearance and sealing characteristics to the JIC system, except the angle of the machined male nose and female flare seat is 45° (Fig. 4). "O" Ring Fittings Seals for "O" ring fittings are formed by compressing an "O" ring against an exposed machined surface on a mounting block or hydraulic component part. The "O" ring must be compatible with the type of hydraulic fluid used (Fig. 5). An "O" ring boss connection is made of a male straight thread

Jan 10, 1983

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004