Search Documents

A semi-automatic device has been constructed that can be used to check the solution strength of cyanide solutions. It consists of a wheel on which a gold-foil-bearing glass slide is mounted. The wheel moves the gold foil through the solution under test and intercepts a light beam. As the gold foil is attacked by the cyanide solution its light absorption diminishes. The successive in-crease in transmitted light intensity is recorded and gives a measure of the gold dissolution rate. Curves have been obtained to show the effect of cyanide concentration and oxygen content on dissolution rates. Details are presented of the construction of the unit, and some practical operating procedures are outlined. 0 NE of the important, although often neglected, factors in the extraction of gold by cyanidation is the actual dissolving strength of the cyanide solution. This depends in a

Jan 1, 1964

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010

By E. O. Chisholm

Synopsis The colour changes effected in a solution of dithizone by trace amounts of copper, lead, and zinc mineralization provide a sensitive field test for these metals. The method has been used with success by the United States Geological Survey to trace zinc orebodies under residual soils. The dithizone test is used here on samples of non-residual soil overlying a gold-bearing zone in which the gold is associated with disseminated sphalerite, galena, and chalco-pyrite. A gold-bearing zone was successfully traced under overburden ranging from a few inches to five feet in depth by means of this method. The method may prove useful in guiding preliminary trenching through light overburden, by outlining the extent of copper, lead, and zinc mineralization. Introduction The dithizone test affords a rapid, simple, and delicate test for the presence of zinc in soil and water and is suitable for use under field conditions. It has recently been used with success by the United States Geological Survey to outline a zinc-rich area in the residual soil over a primary zinc deposit in Tennessee. The purpose of the present study was to ascertain whether the method could be used to trace a gold-bearing zone, containing associated zinc mineralization, under shallow, non-residual, glacial overburden. The results obtained indicate that the method can be used to guide preliminary trenching in overburden up to six feet in depth. Tests made of the water near lake-shore outcrops also indicate that favourable prospecting zones may be located from the water, within five feet of the shore. It is felt that this simple field test should find a wider use in prospecting, because, under certain conditions, it can outline favourable zones and thereby reduce the amount of blind trenching necessary. The following pages describe the type of deposit tested, the method used, the .results obtained, and the difficulties encountered by a novice in the use of this chemical procedure. The author is indebted to the officials of Nor-Penn Mines, Limited, for their co-operation while the tests were being made; to the late Richard Bouska, Kenora prospector, for helpful suggestions; and to F. W. McCamus, University of Toronto undergraduate student, who ably assisted with the work.

Jan 1, 1950

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

On-stream determination of xanthate concentrations can be made by photometric measurements at 313 nm.A simple double-beam instrument was developed for this purpose. A mercury lamp is used as the light source and a composite filter of UGll glass and chromate solution is used to isolate the required spectral region. The light beam is split into two components of approximately equal intensity. One component is passed through a reference cell containing water to a photo detector; the other component is passed through the xanthate solution to a second photo detector. The reference signal controls amplifier gain to eliminate effects of lamp intensity changes and the amplified sample signal can then be used to measure xanthate concentration.Plant trials showed that provided a clear solution free of air bubbles was obtained from an on-stream filter, the instrument indicated the xanthate concentration and operated satisfactorily for long periods.

Jan 1, 1973

By L. Li

ABSTRACT Stope backfilling is a common operation in many underground mines, which requires a barricade at the base of the stope near the drift entrance to retain the backfill in place. In this paper, the distribution of pore-water pressure in barricades made of waste rock is analyzed. An analytical solution is introduced and applied to estimate the pore-water pressure along the base and full height of the barricade. Results show that the analytical solution generally accurately predicts the distribution of pore-water pressure obtained from the numerical calculations, especially in the upstream part of the barricade, where it is most critical.

Jan 1, 2013

By O. B. Bucklen

The Coal Research Bureau of the School of Mines at West Virginia University, using a modified design of a Russian flotation device, was able to obtain a clean coal product containing 7.64 percent ash with 94 percent yield and 97 percent coal recovery. This favorable performance was obtained with the semi-pilot scale flotation cell operating as a simulated three stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient "operation on high density feed slurry, and absence of moving parts.

Jan 1, 1964

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By K. D. Eigenbrod

A case history is presented of a landslide that occurred adjacent to a highway in the valley of the North Saskatchewan River, about 12 miles upstream of Edmonton, Alberta. The slide took place in the late fall of 1965 following excavations associated with highway improvements that deepened the slope and cut it back to 20º. The slide occurred in the Upper Cretaceous Edmonton Formation. Till covers the bedrock at the location. The bedrock consists of interbedded mudstone, claystone, and sandstone with layers of bentonite and coal. The field investigation consisted of a series of pits at the toe of the slide and seven boreholes around it. Undisturbed samples were taken with a Pitcher Sampler and piezometers were installed at various depths in the section. The slide had taken place on a horizontal bentonitic clay layer and it crossed softened mudstone in the back slope. Three piezometric levels were detected but no water pressures were found along the horizontal portion of the slip surface because it was in contact with a free-draining coal layer. Borehole evidence revealed that the bentonitic clay layer was sheared in place beyond the confines of the slide zone. Although this slide was a first-time occurrence, it was part of a much larger slide block that moved presumably when the valley was being formed. Laboratory tests were carried out to determine the shear strength parameters of the bentonitic clay and the back slope material. These parameters together with the observed water pressure distribution in the slide area gave a factor of safety of 1.01 in a non-circular limiting equilibrium analysis. The case history is particularly instructive in indicating the care that must be taken to obtain representative information for stability analysis when geological and groundwater conditions are non-uniform. The origin of the sheared clay is discussed.

Jan 1, 1972

By W. E. Gaby

THE form of dip chart here presented for the use of the profession was devised by the author when he was confronted with a particularly heavy job of geological section making and. did not have any of the usual tables or charts at hand. This was at the property of the Teziutlan Copper Co. in Puebla, Mexico, where the orebodies are much faulted and lie conformably with a slightly inclined and. much folded schist. Because of the low dip and the folding of the orebodies, the engineering, and geological data respecting them were best represented on vertical cross-sections quite closely spaced. A less finished form of the chart was published in the Mining & Scientific Press of Aug. 6, 1921, with an explanation of its use. I have checked the new drawing for accuracy against the calculated table given, and constructed an explanatory diagram beneath. As some geologists are accustomed to using the table, I have included it, since no advantage is obtained by mere interpolations from the chart to get the required angle, except as it gives a mental picture of this angle. The chart gives a more rapid and much easier solution when cases multiply so that it becomes desirable to eliminate the tedious manipulations of a separate protractor. In fact, using the parallel ruler as des-cribed, it is not even necessary to make note of the angle sought. It is brought out graphically, leaving the mind free to note the correlations. The chart itself may be made more convenient by reproduction on celluloid with a slot running on the zero line of the protractor.

Jan 9, 1922

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By D. B. Buddecke

Powell Bend Mine, located in Bastrop County, Texas, is owned by the Lower Colorado River Authority (LCRA). The mine is operated under contract by the Powell Bend Mining Company (PBHC), an affiliate of Pittsburg and Midway Coal Mining Co., and produces 210,000 tons of 6500 BTU/LB lignite per year for LCRA's Fayette Power Project near La Grange, Texas. PBHC operates the surface strip mine one shift per day, five days per week with a total of nine employees; six operations/maintenance and three office/supervision. The mine's productivity in 1988 averaged 100.3 tons per manshift using an l8-cubic yard dragline to uncover the lignite. Delivered cost to LCRA, F.O.B. mine, is $6.11 per ton, which includes water control and final reclamation.

Jan 1, 1990

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012

By Ker-Chang Hsieh

Four three-phase equilibria and one two-phase equilibrium in the FeNi- S-0 quaternary system in the vicinity of 1023 K and Pso2 = 1 atm were studied using the following emf cell 2 Pt,o2 (air)Zr02 .CaO/Pso2 = 1 atm, mixture of phases, Au The four three-phase equilibria are sp + (Fe,Ni )S + Ni 3s2, sp + Ni 3s2 + NiO, sp + NiO + N1S04 and Fe2 o3 + sp + (Fe,NOS04 -Y:he two-phase equilibrium is sp + (Fe,Ni)S. The two-.phase equilibrium was measured by using mixtures containing a major portion of one phase and a minor portion of the other. The results are presented in terms of oxygen potential as a function of YNi = nNi/(nN1+nFe) at constant temperature and pso2 = 1 atm. The stability diagram was also calculated using appropriate thermodynamic models for all the pertinent phases. The calculated diagram is in accord with the measured ones.

Jan 1, 1985