Search Documents

By AIME AIME

A FALL meeting that should have repercussions both in the "Transactions" and MINING AND METALLURGY was that of the Industrial Minerals Division (Nonmetallics) at Wilmington, Oct. 21-23; headquarters, Du Pont Hotel. The sixteen technical papers and two addresses were substantial and interesting. Moreover, in every instance but one, the author made the presentation, and the one exception must have been next of kin because the ensuing discussion indicated his command of the subject. The meeting schedule clicked at every turn, thanks to Dr. Gillson, chairman of the local committee, and even the four field trips adhered to the time table. The program pre-empted morning, noon, afternoon and night two general luncheons, two dinners, and an evening technical session reminding one of the Annual Meeting. Only the registration was disappointing - about 80.

Jan 1, 1943

By S. Annavarapu

"Fragment size distributions play an important part in the design and planning of block cave mining operations. Though several methods have been proposed for estimating fragment size distributions in advance of mining, the calibration of these estimating procedures to field measurements has been a challenge. The Block Size Estimator (BSE) program was developed for providing an assessment of primary fragmentation expected in a block cave mine using drill-core piece length data and joint characteristics from the exploration and geotechnical evaluation programmes. In order to validate the results from the BSE program, the drill-core piece length data and the joint characteristics in different rock types from the DOZ block cave mine in Indonesia were used to help generate fragment size distributions in different areas of the mine. The predicted fragment size distributions were compared with the fragmentation observed at the drawpoints during operation of the mine.This paper presents the details of the validation of the fragment size estimates by the BSE program using fragment size distribution data from the drawpoints at the extraction level at the DOZ block cave mine, and the challenges encountered in developing reasonable correlations between the estimated and measured fragment size distributions. IntroductionThe assessment of fragmentation is an important aspect of the design and planning of the block cave mining method, and forms an integral part of the design of the excavations at the extraction level and the selection of material handling systems for transporting the ore to the processing stations. Secondary blasting requirements can also be estimated based on the fragment size distributions developed for the block cave (Laubscher, 1994).Several methods of estimating fragment size distributions in block cave mines have been developed based on joint set parameters estimated from structural data from oriented core drilling campaigns and mapping of available excavations and outcrops. The BCF program (Esterhuizen, 1999) estimates the fragmentation using a combination of empirical, analytical, and rational methods to model the behaviour of materials during the primary and secondary fragmentation processes. The program JKFrag uses advanced tessellation of joint traces to create rock blocks and then generate fragment size distributions (Brown, 2002). Nickson, Coulson and Hussey (2000) presented the details of processing of the geotechnical data from the Mont Porphyre project, including an assessment of block sizes from the data collected on the core logging sheet. The distance between natural fractures was used to create distributions of block lengths, and a distribution of potential block sizes was estimated assuming that the blocks had equal dimensions in all directions. The results agreed closely with the results of the BCF program. Hadjigeorgiou, Grennon, and Nickson (2002) demonstrated the use of oriented borehole data to provide characteristic block size distributions for a mining project using a software package called Stereoblock, which generates a three-dimensional joint network for a given volume and calculates the volumes of blocks created by the intersections of these joints, simulated as circular planes. The distributions of joint orientation and joint spacing generated from statistical analysis of the oriented core data are used for the creation of the Stereoblock model. The diameter of the circular planes representing the joints is determined based on the mean and standard deviation of the joint trace length obtained from scan-line mapping."

May 1, 2019

By L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly. However, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics—namely, size and location—are of great importance in reducing the risk of mine fire injuries. A new, improved fire location algorithm has been developed and integrated into an atmospheric monitoring system (AMS) program by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve the detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

Reprocessing of historic gold tailings is a common activity in South Africa, while base metal tailings offer similar reprocessing potential. The historic base metal tailings of the Namib Pb–Zn mine (Erongo Region, Namibia) still contain valuable resources of Pb and Zn in carbonate-rich matter. Micro-analysis of primary ore minerals identifies some galena as argentiferous and sphalerite as the principal host of Cd. This study demonstrates that knowledge of primary ore mineralogy helps to reveal the hosts of valuable commodities (Ag, Cd) and that field-portable X-ray fluorescence tools allow precise and accurate determinations of major and minor elements like Zn and Cd in such carbonate-rich material. Although there are limitations to directly determine the contents of certain element (i.e., As, Sb, In), linear correlations allow prediction of the likely abundance of these elements. Providing that the inter-mineral and inter-element relations are understood and there is consistency in sampling and analytical methodology, portable X-ray fluorescence analysis is an effective method to evaluate the chemical characteristics of base metal tailings for a range of major and trace elements.

Sep 9, 2024

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981

By J. Budac, R. Krentz, P. Cordingley, G. Freeman, M. E. Chalkley, H. Scheie

Pressure hydrometallurgical unit operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation for fifty years. This paper traces the history of Sherritt from its origins in northern Manitoba, and the development of the first hydrometallurgical nickel-cobalt refinery in 1954, utilizing pressure hydrometallurgy, to the modern day refinery. Sherritt's involvement with pressure hydrometallurgy during the past 50 years has included the operation of the refinery, the development and licensing of technology, incorporating pressure hydrometallurgical unit operations, to more than 30 companies worldwide, the joint venture at Moa, Cuba involving both leaching and precipitation at elevated temperature and pressure, and the production of specialty metal powders. Developments in each of these areas are reviewed.

Jan 1, 2004

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By D. P. Cook, M. I. Bloch, J. A. Dantzig

"In this article, we describe a combined experimental and computational program to study the filling of automotive wheels during low pressure die casting. Experiments are performed by placing thermocouples into the mold walls of a production caster for the Ford F 113 wheel to measure the temperature profiles in the die during processing, and to infer the filling pattern. Computational models are also developed using a 36° section of the wheel pattern, taken directly from CAD data files. We use these models to simulate the filling and heat transfer processes. Comparison between experimental and computational results are presented, demonstrating the viability of this procedure.IntroductionAutomotive companies are using increasing amounts of aluminum in production vehicles: While the main driving force is improved fuel economy through weight reduction, replacing steel wheels by aluminum also offers the potential for improved vehicle performance by reducing unsprung mass. For these reasons, many new vehicles are now supplied with cast aluminum alloy wheels, and the aftermarket for these wheels continues to grow.The most common production process for these wheels is low pressure die casting. The process is subject to numerous defects, including microporosity, cold shuts, cold folds, misruns and inclusions. Scrap rates at the caster of the order of 10% are not uncommon. Many wheels also have large production runs, into the hundreds of thousands of wheels per year. Thus, the cost savings from even small reductions in scrap rate have the potential to be quite significant.Most of the defects are associated with the filling and solidification processes in the mold. The molds are air cooled, and the placement and sizing of cooling passages is currently as much art as science. The ultimate goal of this project is to improve that situation, by implementing simulation procedures that enable engineering design methods to be used in die and process specification."

Jan 1, 2000

By F. Sill

The disposal of residual material from processing and combustion of coal, from incineration of domestic refuse and sewage sludges kind to the environment is a prior task for the future. Deutsche Montan Technologie (DMT) has developed a new technique which makes possible to fill-up goaf cavities behind running caving systems in coalmining. In a mixing and pumping station on the surface high concentrated suspensions are produced from the above mentioned materials. The paste is pumped through pipes to the coalfaces and via trailing discharge pipes stretched to the fracture zone in the caved-in goaf. Since three years a special designed plant is working successfully on a coal mine of Ruhrkohie AG.

Jan 1, 1994

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By D. J. Robertson

"THE copper smelting operation of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, generates a gas flow of 350,000 c.f.m. at n.t.p. This gas stream passes to atmosphere through a 20-foot diameter by 250-foot brick stack, carrying with it an appreciable dust burden in the form of metallic oxide fumes. The flow constituents during the period 1952 and 1953 and •before gas filtration was included in the treatment scheme are shown in Table I. This paper describes the gas filtration treatment which was installed in 1957, using glass cloth media to recover this dust burden, and discusses the associated problem as its treatment for recovery of zinc and cadmium.The metallurgical details associated with the problem are illustrated by a description of the material flow sequence of the Company's hydrometallurgical zinc plant and copper smelter. In this ore processing complex, the zinc plant and copper smelter form an integrated unit within which intermediate zincrich products of each operation enter the treatment circuit of the other."

Jan 1, 1960

By Anne Kvithyld

Silicon solar cells, that convert the energy of sunlight into electric energy, are attractive sources of energy. In the production line wafers of solar cells are sliced from a multicrystaline ingot solidified unidirectionally. Recycling scrap from top and sides of such ingots is addressed. SiC and Si3N4 inclusions are a major problem. Scrap from Scan Wafer ASA is melted in a high vacuum furnace at around 1500ºC. The filters, from commercial producers, are C and SiC with 10, 20 and 30 ppi. Characterisation of inclusions before and after filtration, and in the filter itself, is performed by microscopy. Dissolution of silicon in acid and counting of the un-dissolved inclusions is also carried out. In the filter Si3N4 needles and SiC inclusions were identified. The amount of these inclusions in the filtered silicon is much less than in the input. In conclusion, filtration using SiC and C filters in vacuum system in argon atmosphere removes SiC and Si3N4 inclusions from solar cell scrap. Flow of metal through the filters is not a problem. These results are promising with scale-up to industrial application in mind.

Jan 1, 2006

By Beate Ina Jenssen

Ferric iron removal from the nickel electrolyte at Glencore Nikkelverk AS in Kristiansand, Norway, is achieved by precipitation of iron hydroxide followed by filtration, and it is desirable to improve filtration properties of the precipitated iron hydroxide in order to decrease the filtration time. The effect of increasing the residence time from the current 45 min to 75 min and temperature from 65 °C to 90 °C on the filtration properties of the precipitated iron hydroxide (akaganéite) was studied by simulating the industrial process conditions in a continuous reactor setup operating at steady state, using ferrous-containing process solution as feed material. It was possible to decrease the filter cake resistance by both increasing residence time and temperature, but temperature gave the most pronounced effect and reduced the filter cake resistance by one order of magnitude.

By J. G. Groppo

Laboratory settling and filtration testing was conducted on wet processed fly ash in order to determine the applicability of conventional dewatering techniques to reduce the moisture content prior to drying. Settling tests showed that acceptable clarity (<1.5 g/l suspended solids) could be achieved after as little as 6 minutes of settling. After settling to a consistency of 40 weight % solids, continuous laboratory vacuum filtration testing produced a cake containing below 20% moisture with throughput exceeding 150 lb/ft2/hr.

Jan 1, 1997

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013

"This paper challenges the traditional notion that mine planners need to plan production so as to incur the lowest mining cost. For a given mine configuration, a mine that increases its mining rate will incur increased mining costs. In an environment in which operations are fixated on cost reduction, a proposal that increases costs will not be readily accepted. Such a proposal requires financial justification—the increase in costs might be recuperated by the additional production. This paper evaluates the net present value (NPV) across a range of copper prices for two underground orebodies located at different depths, using a production rate of 300 kt per quarter and a scenario that introduces additional equipment and costs for 450 kt per quarter. The evaluation was based on the changes of NPV for the orebody located at a shallow depth compared with the orebody at a greater depth. Discrete event simulation combined with mixed integer programming was used for analysis. Unlike traditional sensitivity analysis, this study re-optimizes the mine plan for each commodity price at each production rate. The results show that, for the low mining rate at the final copper price, an NPV of A$1530.64 million is achieved, whereas an NPV of A$1537.59 million is achieved at a higher mining rate. Even though pushing mining rates beyond traditional limits may increase mining costs, this option may be beneficial at certain commodity prices, particularly when prices are elevated. IntroductionA traditional notion among mine planners is that mining rates should be planned in such a way as to reduce production costs. This concept generally relates to the mining rate that results in the highest machine utilization for the selected equipment. Although an existing mine may consider increasing its mining rate by adding equipment to a given mine configuration, this typically increases mining costs. In an environment in which operations are fixated on cost reduction, a proposal to increase costs may be very difficult to argue for. The value of the mine plan is well recognized as varying with the mining rate for a given orebody (Smith, 1997)"

Jan 1, 2017